Question about 1999 Chevrolet Corvette

2 Answers

Left turn signal

Bulb burnt out how do i get to it. I have removed the headlight bezel as suggested but can not locate where bulb is

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I've changed mine a few times .......If you have removed the headlight thats good just reach in to the front of the bumper. You should be able to reach the wire to the turn signal. Just twist and pull on the hard plastic that goes into the light case. Reverse procedures to install.

Hope this helps!

Posted on Nov 16, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Through corvette forum website they give instructions to do it through the headlights.

Posted on Nov 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change headlamp bulbs


Changing the headlight bulb is a little bitdifficult for those not familiar with the vehicle. Both the high and low beamsare encased in a sealed unit, which also contains the turn signal, parkinglights, and side reflector. To change a single headlight, the entire headlightcompartment must be removed from the car. Once you understand how to remove thesealed headlight unit from the car, replacing the bulb is relatively simple.Follow the steps below on how to change the headlamp bulb in this car. Removal 1. Open the hood of the Jeep and locate thelong, headlamp jackscrew. The screw is located almost directly above theheadlight unit and can be removed using a 7-mm socket wrench. This will allowyou to remove the bezel from the grill opening panel. Remove the three screwsattached to the retaining ring to the headlight console. The screws are locatedon the bottom front and side of the unit. In some models the screws have beenreplaced with ball-stud alignment posts, enabling you to remove the headlightunit by simply wiggling it loose. 3. Disconnect the headlamp bulb wireharness connector located at the front of the headlight unit. This is locateddirectly above and between the parking and turning bulbs. 4. Separate the sealed headlight unit fromthe vehicle; disconnect and replace the old bulb. The high beam is locatedtoward the center of the car. The low beam is the bulb on the outermost edge ofthe unit. This is how to Install 1. Reconnect the headlamp bulb's wireharness-connector. Then Replace the headlight unit in the headlight canister. Positionthe retaining ring back in its original position and install the three screwsagain. If you wiggled the unit out, ensure that it is replaced firmly. 2. Install the headlamp bezel by replacingthe 7-mm jackscrew on the inside of the hood. Make sure all connections aretight before starting the car and inspecting the replacement.

Jan 14, 2011 | 2000 Jeep Grand Cherokee

1 Answer

How do you replace xeon headlight low beam bulb


Inspect/Replace There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.
f19-22.jpg Comparing the old and ther replacement headlamps. To Replace:
  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).

Nov 05, 2010 | 2005 Volvo S80

2 Answers

How do I replace a left hand side low beam light on a Subaru Tribeca 2008


Inspect/Replace There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.
f19-22.jpg Comparing the old and ther replacement headlamps. To Replace:
  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).

Oct 28, 2010 | 2008 Subaru B9 Tribeca

1 Answer

Removing and reinstalling a new headlight assembly in a 95 jeep grand cheerokee


LIGHTING Headlights REMOVAL & INSTALLATION Cherokee, Wagoneer and Comanche Models Fig. 1: Remove the top corner headlight bezel mounting screw 91076p12.jpg
Fig. 2: To access the turn signal bulb or headlight bezel mounting screws, remove the 2 turn signal housing retaining screws 91076p13.jpg
Fig. 3: After removing the turn signal housing from the headlight bezel, remove the 2 bezel mounting screws . . . 91076p27.jpg
Fig. 4: . . . then carefully pull the headlight bezel away from the headlight assembly 91076p11.jpg
Fig. 5: Remove the 4 headlight assembly retaining ring screws . . . 91076p07.jpg
Fig. 6: . . . then pull the retaining ring off of the headlight assembly 91076p06.jpg
Fig. 7: Pull the headlight assembly away from the vehicle just far enough to disengage the electrical connector from behind the headlight 91076p28.jpg
  1. Remove the headlamp bezel and retaining ring attaching screws. Remove the bezel and retaining ring.
  2. Pull the headlight out, disconnect the wire harness and remove the headlight from the vehicle.
  3. Install the headlight in the reverse order of removal.
Grand Cherokee and Grand Wagoneer Models
  1. Open the hood, reach into the engine compartment and locate the lock ring supporting the bulb assembly.
  2. Rotate the lock ring 1?8 turn counterclockwise and pull the bulb straight out from the housing. To install:
  3. Install a new bulb and position the bulb assembly in the lamp housing.
  4. Rotate the lock ring 1?8 turn clockwise to secure.
----
The Grand Cherokee will have an assembly that is fastened with bolts and screws to the body.
Get the new assembly and compare to the old one to see where to unfasten the bolts and other fasteners to aid in removing quickly.

Oct 08, 2010 | 1995 Jeep Grand Cherokee

2 Answers

How do you change a front turn signal bulb on a x type jaguar


In the back of the low bulb unit, is a round cover, turn it to remove it, then you have access to the bulbs, you´ll need patience large and thin fingers. I suggest you to buy the bulb first and a good quality one, because you´ll need to work on this with a cold engine.

Aug 11, 2010 | 2002 Jaguar X-Type

1 Answer

How do I replace the passenger side corner light and front side turn signal light?


Front Turn Signal & Parking Lights


7ccc73e.gif
Remove the 2 parking light housing retaining screws ...


9898a80.gif
... then pull the housing away from the vehicle far enough to remove the bulb socket from behind the housing. Turn the socket counterclockwise and pull


a323ae9.gif
Push the bulb in the socket gently and turn clockwise, then pull the bulb out of the socket. Note the offset retaining ears on each side of the bulb


  1. Remove the screws from the lens and separate the lens from the headlight bezel.
  2. Remove the headlight bezel.
  3. Remove the screws from the turn signal housing and pull it out.
  4. Turn the bulb socket counterclockwise 1/3 turn and remove it.
  5. Installation is the reverse of removal.


Side Marker Lights
  1. Remove the screws from the marker lens and separate the lens from the headlight bezel.
  2. Pull the bulb from its socket in the back of the lens.
  3. Installation is the reverse of removal.

Feb 14, 2010 | 1997 Jeep Grand Cherokee

2 Answers

How do i get to the front turn signal bulb 1997 Jeep grand cherokee?


Front Turn Signal & Parking Lights

6bad7be.gif
Remove the 2 parking light housing retaining screws ...

36b7e3d.gif
... then pull the housing away from the vehicle far enough to remove the bulb socket from behind the housing. Turn the socket counterclockwise and pull

5206de4.gif
Push the bulb in the socket gently and turn clockwise, then pull the bulb out of the socket. Note the offset retaining ears on each side of the bulb

  1. Remove the screws from the lens and separate the lens from the headlight bezel.
  2. Remove the headlight bezel.
  3. Remove the screws from the turn signal housing and pull it out.
  4. Turn the bulb socket counterclockwise 1/3 turn and remove it.
  5. Installation is the reverse of removal.

Oct 12, 2009 | 2002 Jeep Grand Cherokee

1 Answer

99 calvalier front left turn signal bulb burnt. how do you get to the bulb to replace it?


Remove the upper air intake splash shield.
Remove the headlight retainer nuts (2)
Remove the headlight/blinker assembly
Carefull the blinker has a retainer post with a rubber retainer on the fender
Remove bulb

Jun 21, 2009 | 2001 Chevrolet Cavalier

2 Answers

How do I change the lowbeam headlight on my 2003 Chev Trail Blaze


hi..Should be a Halogen bulb High-low beam combo maybe.
As you are looking down at the back of the headlight assembly
gently push down on the clip that holds the wiring harness to the
bulb. Now rotate the bulb counter clock wise (left) and then remove
it. Reverse process to install.
check it out..
thank u..
rate me..

Mar 10, 2009 | 2006 Chevrolet Trailblazer Ext

2 Answers

Changing the headlight in a '02 Mazda tribute


The bulb is actually very easy and straight forward to replace.

If you are replacing one bulb, I suggest doing both at the same time and a twin pack is less than buying two packs seperately.
  • Removal
  1. Holding the connector on the sides squeeze and pull back away from you.
  2. Once the connector is removed, gently pull the rubber boot back.
  3. This will revail a snap type of clip. NOTE bottom of clip does come off. Push each top side of the clips towards you to relase them.
  4. Once the tops of the clip are undone let the clip swing down.
  5. slide the bulb out of the lens.
Caution DO NOT TOUCH THE NEW BULB WITH YOUR BARE HANDS. THE BODY OILS ON YOUR HANDS CAN CAUSE THE BULB TO GET HOT SPOTS AND BURN OUT QUICKLY.
  • Install
  1. To install the new bulb ensure the three keys are properly aligned with the lens when installed.
  2. Install buld into lens.
  3. Place clip over bulb.
  4. Place boot over bulbs making sure it is fully engaged into lens.
  5. Push connector back onto bulb.
  6. Check lights to make sure everything works.



Nov 05, 2008 | 2003 Mazda Mazda6

Not finding what you are looking for?
1999 Chevrolet Corvette Logo

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...