Question about 2002 Land Rover Freelander

1 Answer

Don`t start I was trying to get to the Thermostat housing assembly in my car.I disconnect the negative cable from the battery and some electrical component fom the fuel injector , I din`t get to the thermostat becouse it was difficult, I connet everything back together and now my car doesn`t start, can you help me to find out what is the problem

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 89 Answers

What engine is fitted ?

Posted on Nov 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for location of thermostat housing to change thermostat


zjlimited_617.jpg

Fig. 5: View of the thermostat and related components - 2.4L engine (click for zoom)


3.1L and 3.3L Engines
  1. Disconnect the negative battery cable.
  2. Drain the cooling system to a level below the thermostat housing.
  3. Remove the air cleaner assembly.
  4. Disconnect the surge tank line from the thermostat housing.
  5. Remove thermostat housing-to-intake manifold attaching bolt and nut, then remove the housing.
  6. Remove the thermostat.

Hope this helps.

Feb 03, 2011 | 1997 Buick Skylark

1 Answer

I need to know where the thermostat goes on 2002 jeep liberty 6cy?


just left of the crankshaft pulley

a56facc.gif
  1. Disconnect negative battery cable at battery.
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Remove splash shield.
  5. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  6. Remove thermostat housing mounting bolts, thermostat housing and thermostat .
To install:
  1. Clean mating areas of timing chain cover and thermostat housing.
  2. Install thermostat (spring side down) into recessed machined groove on housing assembly. Make sure rubber seal locating tab is positioned in the corresponding notch in the housing.
  3. Position thermostat housing on timing chain cover.
  4. Install two housing-to-timing chain cover bolts. Tighten bolts to 105 inch lbs. (12 Nm) torque.
  5. Install lower radiator hose on thermostat housing.
  6. Install splash shield.
  7. Lower vehicle.
  8. Fill cooling system.
  9. Connect negative battery cable to battery.
  10. Start and warm the engine. Check for leaks.

Oct 04, 2010 | Jeep Liberty Cars & Trucks

1 Answer

Car starting to run hot at times, notice that the temp gage will go up to hot when the air or heat is on. Thinking that it could be the thermostat. Where is the thermostat located in order to replace it.


Thermostat is under the air cleaner outlet. also see my tips at http://www.fixya.com/cars/r5929960-s_thermostat for more ideas on possible causes of overheating.


2.5L & 3.0L Engines

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:

    Negative battery cable Fuse 38 from the engine compartment fuse box Air cleaner outlet pipe Thermostat housing and thermostat
  4. To install, reverse removal procedure. Tighten thermostat housing bolts to 13 ft. lbs. (18 Nm).


4.0L & 4.2L Engines


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:

    Negative battery cable Air cleaner outlet pipe Engine cover retaining bracket Thermostat housing front cover assembly Thermostat
  4. To install, reverse removal procedure.

Sep 28, 2010 | 2001 Jaguar S-Type

1 Answer

What do i need to take off in order to put the thermostate on a Ford Focus 2007?


Hello! Here is procedure to replace the thermostat on your vehicle.....Guru.....Saailer


  1. Thermostat and housing are an assembly
  2. Disconnect battery negative cable from battery and properly isolate to prevent accidental reconnection.

  3. Drain the cooling system.
  4. Raise vehicle.
  5. Remove or disconnect the following:

    Accessory drive belt shield Accessory drive belt Two power steering hose bracket retaining nuts and position the hose and brackets aside. Cooling fan motor and shroud 3 A/C compressor bolts and position the compressor aside Hoses from the thermostat housing
  6. Remove the bolts, the thermostat housing and the thermostat as an assembly.

To install:

NOTE Lubricate the thermostat housing O-ring with clean engine coolant.
  1. Install or connect the following:

    New thermostat/housing assembly and tighten the bolts to 89 inch lbs. (10 Nm) Hoses to the thermostat housing A/C compressor bracket and compressor and tighten the bolts to 18 ft. lbs. (25 Nm) Cooling fan motor and shroud Power steering hose, bracket and tighten the nuts to 89 inch lbs. (10 Nm)
  2. Fill and bleed the cooling system.
  3. Reconnect the negative battery cable.


retailerIdd874f148debugOnfalsecustomerId117788472vehicleId3089401

Sep 11, 2010 | Ford Focus Cars & Trucks

1 Answer

How do I replace the thermostat


REMOVAL AND INSTALLATION
3.1L Engine
  1. Disconnect the negative battery cable.
  2. Partially drain the cooling system into a suitable container, to a level below the thermostat.
  3. Disconnect the radiator hose from the thermostat housing.
  4. Unfasten the thermostat housing bolts.
  5. Remove the housing. Note the installed position of the thermostat, then remove the thermostat and gasket.
  6. Thoroughly clean the gasket mating surfaces.
See Figure 2
54655f1.jpg


Fig. 2: Exploded view of the thermostat and housing assembly

To install:
  1. Position the new thermostat in the manifold.
The pellet MUST go towards the engine.
  1. Install a new gasket, using sealer as necessary.
  2. Install the housing and secure with the retaining bolts. Tighten the bolts to 25 Nm (18 ft. lbs.)
  3. Reconnect the radiator hose to the housing.
  4. Replace the coolant. Check for leaks.
  5. Connect the negative battery cable.

Hope helps (remember arted this).

Aug 12, 2010 | 1999 Pontiac Montana

2 Answers

Where is the thermostat located


77f1c56.jpg

Fig. The location of the thermostat and its housing on the 3.7L engine

  1. Disconnect negative battery cable at battery.
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Remove splash shield.
  5. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  6. Remove thermostat housing mounting bolts, thermostat housing and thermostat .
To install:
  1. Clean mating areas of timing chain cover and thermostat housing.
  2. Install thermostat (spring side down) into recessed machined groove on housing assembly. Make sure rubber seal locating tab is positioned in the corresponding notch in the housing.
  3. Position thermostat housing on timing chain cover.
  4. Install two housing-to-timing chain cover bolts. Tighten bolts to 105 inch lbs. (12 Nm) torque.
  5. Install lower radiator hose on thermostat housing.
  6. Install splash shield.
  7. Lower vehicle.
  8. Fill cooling system.
  9. Connect negative battery cable to battery.
  10. Start and warm the engine. Check for leaks.

Hope helps (remember rated and comment this).

Aug 06, 2010 | 2002 Jeep Liberty

1 Answer

CHANGE THERSTAT ON 2002 JEEP LIBERTY


3.7L Engine - Thermostat
  1. Disconnect negative battery cable at battery.
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Remove splash shield.
  5. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  6. Remove thermostat housing mounting bolts, thermostat housing and thermostat .

    a105ca1.jpg
    Fig. The location of the thermostat and its housing on the 3.7L engine (click for zoom)
To install:
  1. Clean mating areas of timing chain cover and thermostat housing.
  2. Install thermostat (spring side down) into recessed machined groove on housing assembly. Make sure rubber seal locating tab is positioned in the corresponding notch in the housing.
  3. Position thermostat housing on timing chain cover.
  4. Install two housing-to-timing chain cover bolts. Tighten bolts to 105 inch lbs. (12 Nm) torque.
  5. Install lower radiator hose on thermostat housing.
  6. Install splash shield.
  7. Lower vehicle.
  8. Fill cooling system.
  9. Connect negative battery cable to battery.
  10. Start and warm the engine. Check for leaks.

Hope helps (remember rated this).

Aug 04, 2010 | Jeep Liberty Cars & Trucks

1 Answer

How to replace a thermostat 1996 mazda mellinia


Thermostat - REMOVAL & INSTALLATION

CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
1.5L, 1.6L, 1.8L (except K8) and 2.2L Engines
  1. Disconnect the negative battery cable. Drain the radiator to below the level of the thermostat.
  2. If necessary, remove the air cleaner assembly.
  3. If necessary, disconnect the coolant temperature switch at the thermostat housing.
  1. Remove the upper radiator hose.
  2. Remove the mounting nuts, thermostat housing, thermostat and gasket.
Do not pry the housing off.


To install:
  1. Clean the thermostat housing and the cylinder head mating surfaces.
  2. Insert the thermostat into the rear cylinder head housing with the jiggle pin at the top. The spring side of the thermostat should face the housing.
  3. Position a new gasket onto the studs with the seal print side facing the rear cylinder housing.
  4. Install the thermostat housing and 2 nuts. Tighten the nuts to 14-22 ft. lbs. (19-5 Nm).
  5. Install the upper radiator hose.
  6. If detached, connect the coolant temperature switch.
  7. If removed, install the air cleaner housing.
  8. Fill the cooling system. Connect the negative battery cable, start the engine and check for leaks. Check the coolant level and add coolant, as necessary.


2.0L Engine
See Figures 3, 4, 5, 6, 7, 8, 9 and 10
  1. Disconnect the negative battery cable.
  2. Drain the engine coolant from the radiator to below the level of the thermostat.
  1. Disconnect the lower radiator hose from the engine.
  2. Remove the housing bolts, thermostat housing, thermostat and gasket.
Do not pry the housing off.


To install:
  1. Clean the thermostat housing and the cylinder head mating surfaces.
  2. Make sure that the thermostat jiggle pin is aligned with the gasket projection.
  3. Install the thermostat to the housing. Align the gasket projection with the opening in the housing. The spring side of the thermostat should face into the housing.
  4. Install the thermostat housing cover and tighten both bolts to 14-19 ft. lbs. (19-25 Nm).
  5. Fill the cooling system. Connect the negative battery cable, start the engine and check for leaks. Check the coolant level and add coolant, as necessary.

Hope helps (remember rated this).

Jul 08, 2010 | 1996 Mazda Millenia

1 Answer

How to change the Tstat on 1999 olds silhouette


3.1L Engines
  1. Disconnect the negative battery cable.
  2. Partially drain the cooling system into a suitable container, to a level below the thermostat.
  3. Disconnect the radiator hose from the thermostat housing.
  4. Unfasten the thermostat housing bolts.
  5. Remove the housing. Note the installed position of the thermostat, then remove the thermostat and gasket.
  6. Thoroughly clean the gasket mating surfaces.
69138cc.gif
Exploded view of the thermostat and housing assembly

To install:
  1. Position the new thermostat in the manifold.
    NOTE The pellet MUST go towards the engine.

  2. Install a new gasket, using sealer as necessary.
  3. Install the housing and secure with the retaining bolts. Tighten the bolts to 25 Nm (18 ft. lbs.)
  4. Reconnect the radiator hose to the housing.
  5. Replace the coolant. Check for leaks.
  6. Connect the negative battery cable.

Nov 30, 2009 | 1999 Oldsmobile Silhouette

1 Answer

Replacement of thermostat


This is for 3.1L....if this is not what you have, please let me know the size of the motor!

3.1L Engines
  1. Disconnect the negative battery cable.
  2. Drain the cooling system, into a suitable container, to a level below the thermostat housing.
  3. Remove the air cleaner assembly.
  4. Remove thermostat housing-to-intake manifold attaching bolt and nut, then remove the housing.
db74cbc.gif
Remove the two housing-to-intake manifold bolts and remove the housing

  1. Remove the thermostat.
To install:
  1. Clean all gasket surfaces completely.
  2. Insert the thermostat in the intake manifold.
  3. Attach the thermostat housing to the intake manifold.
  4. Install the mounting bolt and nut. Tighten to 18 ft. lbs. (25 Nm)
  5. Install the air cleaner assembly.
  6. Connect the surge tank line to thermostat housing.
  7. Refill the cooling system.
  8. Connect the negative battery cable, remove the radiator cap, then start the engine. Allow the engine to run with radiator cap removed, until the upper radiator hose becomes hot (thermostat open). With the engine idling, add coolant to the radiator until the level is up to the bottom of the filler neck.
  9. Install the radiator cap, making sure the arrows line up with the overflow tube.

Nov 19, 2009 | 2000 Chevrolet Impala

Not finding what you are looking for?
2002 Land Rover Freelander Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64034 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...