Question about 1991 Acura Legend

1 Answer

FRONT MOTOR MOUNTS

I NEED TO KNOW HOW TO INSTALL NEW ONES.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 132 Answers

With motor in car undo mounting bolts place jack under motor gently jack up until mounts can be moved out of way replace mounts drop jack install nuts and washers simple

Posted on Nov 09, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front motor mount needs replacement


front motor mount is the mount at the front of the engine not the front of the car

Jul 12, 2015 | 2005 Chrysler Pacifica AWD

1 Answer

Where is the motor months for a 93can Dakota n how do fix it


They'll be at the bottom of your engine, one on each side and possible one at one end. One piece will bolt to the side of the engine block, and one piece will bolt to the truck's frame. Between the two pieces will be a rubber vibration damper.

If you need to replace one or more motor mounts, you'll need to jack up the front of the truck enough to comfortably get under it, and support the truck with something that CANNOT fail. If the truck falls off the jack, it WILL KILL YOU DEAD. I like to put two or more spare tires/wheels under the vehicle with me - they take the impact if a jack fails, allowing me to survive.

You'll also need to jack up the engine slightly. Not much, just slightly... more to take the weight off the motor mounts than for anything else.

Work ONE motor mount at a time. DO NOT try to do more than one at a time - it's hellish to let an engine float around in there with no motor mounts while you try to get all those bolts to line up again.

After jacking up the engine slightly, unbolt one motor mount from the engine block. You may need any of several different types of wrenches to do this. Also unbolt the same motor mount from the truck frame. Now you can remove the motor mount altogether, letting the engine hang there between the remaining motor mount(s) and the jack. If you hadn't jacked up the engine, now it would have fallen when you took out the motor mount, and it'd have been EXTREMELY difficult to get it back into position so you could reinstall the new mount.

Installation is the reverse of removal. Bolt it (LOOSELY) to the frame, then to the block. You may need to do some prying to get the last bolts to line up with their holes. After all the bolts are installed loosely, THEN you can tighten them all down. If you tighten some before you install the others, the others may be impossible to line up with their holes.

Finish one, move on to the next.

Jul 30, 2014 | Cars & Trucks

1 Answer

I need to know where they are locatedhow to install ****** & motor mounts on a 1996 buick century


the transmission mount is on the top of the transmission on the drivers side next to the battery,and one motor mount is under the motor on the passenger side next to the harmonic balancer. and the is either one or two mounts on top of the radiator to the front vavle cover

Nov 05, 2012 | 1996 Buick Century

1 Answer

01 kia rio motor mount


your uncles car is a front wheel drive engine whether an auto transaxle or manual transaxle, the motor rubber mounting support is on the side of your engine and transmission near the shock absorbers normally attached to the front collision mounting frame

Mar 02, 2010 | 2001 Kia Rio

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

1 Answer

Need motor mounts for 2004 Chrysler Pacifica


I'm thinking it has 1 motor mount and 2 dog bones. The mounts usually cost around $30 each and the dog bones $20-25 depending on the material their made of. You can replace these yourself, one at a time. The engine has to be jacked up just enough to take the weight off when you remove the mount. After you have it remove, install you new one/ones and tighten. After removing jack, torque the bolts to spec. Same thing is done with the dog bones. It a type of Motor mount that prevents the engine from leaning weight. These are usually located, one front/top engine area and one on bottom engine area.

Jan 13, 2010 | 1995 Mercury Sable

1 Answer

Passenger side front motor mount on 95 ford taurus. how do i replace it? 3.8


There should be only one front mount,there is a 18mm nut on the top of your motor mount below your a/c pump,and there is a 18mm nut on the mount up inside your frame,just remove these 2 nuts(place a jack with a piece of 2x4 on it so you dont destroy your oil pan)jack up the engine enough to remove the mount only,reinstall new mount make sure you install correctly,and facing correct way,remove jack and enjoy the ride

Nov 04, 2009 | 1995 Ford Taurus

3 Answers

Where can i get motor mounts.early 91 specific Saturn SL1


any parts store sells aftermarket ones fairly cheap.....Lee

Oct 31, 2009 | 1991 Saturn SL1

1 Answer

How to repair front electrial window 0n 2003 durago


need to know whats wrong... motor not running, it is running and not moving window etc? the window regulator/motor is sold and serviced as one peice. dealer about 160, local auto parts sell this aftermarket too for 99 bucks, i own one of these lol. it comes with the cables motor and al assembled just install it. only thing is the aftermarket ones are an updated design that requires you to drill a few new holes indoor cage to mount. not hard, even comes with a template. good luck and i hope ive answered you question if not let me know

Sep 03, 2009 | 2003 Dodge Durango

2 Answers

Motor mount, front right, solid or hydraulic?


Hello wrygrl...The OEM (orginal equipment) passenger side motor mount for the 1988 olds ninety-eight was a hydraulic type. After market "solid" type mounts are available for replacement...either type will work. Shop around and get some price quotes, i believe westar makes a solid type mount that sells for around 22 bucks.
Hope this answers your question. Have a safe and happy memorial day weekend.

May 21, 2009 | 1988 Oldsmobile Ninety Eight

Not finding what you are looking for?
1991 Acura Legend Logo

Related Topics:

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...