Question about 2005 Chrysler PT Cruiser

1 Answer

Trouble codes codes po139 ,p0344, p0340

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,035 Answers

Trouble Code: P0139
O2 (B1 S2) Slow Response
Trouble Code Conditions:Engine started; vehicle driven at 20-55 mph with the throttle open for 2 minutes; ECT at more than 158ºF (70C); catalytic converter temperature is more than 1112F (600C); and EVAP purge is active. O2 Sensor signal voltage switches less than 16 times from lean to rich within 20 seconds during monitoring, or will compare the state of change between the front and rear O2 Sensors and if the differences are greater than a calibrated amount, the DTC will set. 3 good trips are required to turn off the MIL.
Possible Causes:

  • Exhaust leak
  • O2 element is contaminated, deteriorated or it has failed
  • O2 signal circuit or return circuit has failed

Trouble Code: P0344
Camshaft Position Sensor Circuit Intermittent
Trouble Code Conditions:Engine cranking or running; system voltage over 10.5v. The PCM detected an intermittent loss of the CMP Sensor signal during the period of 2.5 complete engine revolutions. The failure counter must reach 20 before this code matures and a code is set.
Possible Causes:
  • Wiring harness fault
  • 5v supply circuit open or shorted to ground
  • Tone wheel/pulse ring is damaged or corroded
  • CMP Sensor has failed
  • CMP Sensor signal circuit is open, shorted to ground or battery voltage or 5v supply
  • CMP Sensor ground circuit is open
  • PCM has failed
  • Trouble Code: P0340
    No Camshaft Position Sensor Circuit Failure
    Trouble Code Conditions:Engine cranking or running, system voltage over 10v. The PCM detected CKP pulses without detecting any CMP Sensor pulses for 5 seconds or 2.5 engine revolutions.
    Possible Causes:
  • CMP Sensor connector is damaged, open or it is shorted
  • CMP Sensor signal circuit is open or shorted to ground or to battery voltage or 5v supply circuit
  • CMP Sensor 5v supply circuit is open or shorted to ground or to battery voltage
  • CMP Sensor ground circuit is open
  • CMP Sensor is damaged or has failed
  • CKP Sensor is damaged or has failed
  • PCM has failed
Good luck....

Posted on Nov 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0340 code and p0344 on 3.7 dodge Dakota


First check the easy thing. Have your battery tested. Sensors very sensitive to failing battery. If the battery tests fine then you will need to change the Cam sensor probably a $30 part. On your truck remove the air filter housing & the cam sensor should be easily accessible at the front of the cyl head. Hope this works for you. Based on your P codes it should.

Mar 25, 2014 | 2004 Dodge Dakota

1 Answer

Stalling wont idle


  • egr valve
  • egr sensor
  • cam shaft sensor
  • barometric pressure sensor (map sensor)
vacuum leak somewhere, out of time, broken timing belt or missing teeth.

Dec 12, 2013 | Cars & Trucks

1 Answer

Neon Code P0344


I believe that the splice for the cam sensor is about 8 inches back in the harness. Power to the cam supplies several sensors. I have fixed a few that the splice was bad, There is very little room to work in to get to the splice, but it's not impossible to fix.

Jul 13, 2013 | 2004 Dodge Neon

1 Answer

P0016 what is that n how u fix it


P0016 Crankshaft Position - Camshaft Position Correlation
P0135 O2 Sensor Heater Circuit
P0138 O2 Sensor Circuit High Voltage
P0340 Camshaft Position Sensor "A" Circuit
P0344 Camshaft Position Sensor "A" Circuit Intermittent
P0508 Idle Air Control System Circuit Low
P0522 Engine Oil Pressure Sensor/Switch Low Voltage
_____________--
JMA TRS-5000 Cloning Machine

Jun 03, 2013 | Cars & Trucks

1 Answer

Need to know what dodge codes P0325, P0344 & P0340 mean


0325 knock sensor
0344 cam position sensor intermittent
0340 cam position sensor failure

I would replace the cam position sensor from the codes you provided. The knock sensor
would most likely be related to the sensor failure.

Jun 28, 2011 | Dodge Neon Cars & Trucks

2 Answers

I am having a p0340 and a p0344 code coming on and the check engine light is on. The car is maknig a jerking sensation when driving.Also, the car is not accelerating like it use to and the driving...


P0340 Camshaft Position (CMP) Sensor Circuit
P0344 Camshaft Position Sensor Circuit Intermittent


You'll need to replace the Camshaft Position Sensor and might as well replace the crankshaft sensor as well. With these codes and the symptoms you describe this should clear the problem for you. Also check the wiring harness around both sensors to make sure there are no issues. Maje sure no insulation is cut or missing along the entire run of the associated wiring.

Aug 24, 2010 | 2003 Chrysler PT Cruiser

1 Answer

I have a 2004 Chrysler 300M and am getting fault codes P0344 & P0340. Any ideas of the issue and if the fix is something a can do?


Those 2 codes are for the cam sensor. Replace the cam sensor and that should fix your issue.

Mar 19, 2009 | 2004 Chrysler 300M

1 Answer

Trouble codes P0420 P1681 P0344 P0340 P0420


No I/P Cluster CCD/J1850 Message No CCD/J1850 messages received from the cluster
Received control module

Jul 15, 2008 | Chrysler Concorde Cars & Trucks

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

1,771 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...