Question about 1991 Jeep Wrangler

1 Answer


Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert that has over 500 points.

  • Expert
  • 475 Answers

If this is a high mileage vehicle, you could need a clutch.
Make sure your clutch master is full and there is no air in the system first.

Posted on Nov 05, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2004 ford focus 2.0liter. clutch pedaL GOES TO FLOOR. brake master full of fluid.I clutch master or clutch slave cylinder bad?

a plastic master cyl !

master cyl is bypassing internally

slave cylinder is inside the gearbox bell housing
if its leaking .....gearbox out




Nov 11, 2016 | 2004 Ford Focus

1 Answer

Clutch drops

Yes you could have a bad slave cylinder or a leak on the system

Nov 25, 2013 | 2006 Ford Ranger 4.0

1 Answer

94 Chevy 2500 Clutch Engagement?

You probably have a hydraulic clutch. A hydraulic clutch has both a master and a slave cylinder. The slave cylinder engages/disengages the clutch plate. You might be low on clutch fluid in the master cylinder, or the system may need to bled similar to bleeding brakes. Worst case is you need a new clutch, pressure plate, and throwout bearing. They should all be replaced when doing a clutch job.

Aug 23, 2012 | Cars & Trucks

1 Answer

Clutch engages higher the warmer it gets in my 2002 altima v6 5 spd

pressure plate could be bad they make new broke stuff every day

Oct 17, 2017 | 2002 Nissan Altima

2 Answers

I lost all pressure in my clutch so I replaced the clutch/slave cylinder etc on my 2001 saturn wagon. worked fine for a 2 months. Now all of a sudden I have some pressure in the clutch but it seems out of...

Two possibilties. If you haven't yet replaced the clutch master cylinder there might not be enough pressure to fully engage the clutch. If the master cylinder is full of fluid and has been operating properly until now it could be that you only need to adjust the linkage at the slave cylinder to give a little more throw to the pressure plate. Always try the easiest things first. Good Luck!

Mar 13, 2011 | 2001 Saturn SC

2 Answers

Clutch pedal does not engage clutch

You may have an issue with the slave cylinder. when the slave cylinder is shot or damaged it does not engage the throw out bearing which in turn engages the pressure plate to the clutch plate.

Jan 28, 2011 | 1989 Ford F 150

1 Answer

A new clutch, slave cylinder, and clutch master cylinder were all installed but when i push the clutch pedal down it still doesnt engage the clutch all the way, it acts like it is getting a little pressure...

Have you checked that the slave cylinder is attached firmly where it's supposed to be? Have you refilled the bowl of the master cylinder with braking fluid? And finally have you bled the circuit thoroughly after that?

Aug 01, 2010 | 1994 Eagle Talon

1 Answer

2000 kia sportage clutch works sometimes

The master cylinder only gets low if there is a leak. Your slave cylinder or the master cylinder is leaking. Look under dash were the petal pushed the master cylinder to see if fluid is coming out. Then look at the slave cylinder under the car. It is bolted to the right side of the transmission bell housing. May have to pull rubber boot back on it to check for fluid leakage.

Jan 16, 2010 | 2000 Kia Sephia

2 Answers

No clutch pressure

have u checked the slave cylinder? should be inderneath the drivers side door

Oct 12, 2008 | 1999 BMW 323 Series

Not finding what you are looking for?
1991 Jeep Wrangler Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides