Question about Mitsubishi Montero Sport

3 Answers

Shift solenoid C malfunction - Montero Sport Mitsubishi Cars & Trucks

Posted by on

  • 1 more comment 
  • gtkermit Nov 22, 2008

    my son was driving his 01 sport and the transmission did some crazy things, jumping, jerking, etc. then the check engine light came on and wouldn't shift out of first gear. Fluid was fine, later it drove fine.When we checked the code it said shift solenoid malfunction- check for bad circuit, or connection, or you have a bad solenoid.



    any suggestions?

  • luischav3z Dec 03, 2008

    mine stucks on third and also gave out the code of solenoid C

  • e_fontenot1
    e_fontenot1 Aug 01, 2012

    Replace the shift solenoid. I had same problem when dealer neglected to mention the trans. fluid was low at time of purchase. Luckily it didn't give out until I got about a mile and a half from home. Hope this helps.

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have had the same problem, found out it is the wiring harness off the transmission. When it gets wet, it would cause the transmission to shift hard. After it dried out it would be fine. Mitsubishi has a TSB out on this. You have to remove the wiring harness and check all of the wires, its best to strip them back to make sure that you have no corrosion. Heat shrink them and reattatch. Seams like a error on Mistusbishi design. The bracket that holds the harness it what caused the cut in the wire then the short when it gets wet. Take it to your dealer to have it checked out.

Posted on Dec 18, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 2 Answers

Took it to a transmission shop. They said they thought mechanically transmission was fine but couldn't fix problem. Took it to Mitsubishi Dealer told me I needed a new transmission- $6,000...I don't think so. Had it towed to a trusted transmission shop. We replaced the shift solenoids, still same problem. Finally took it to an incredibly smart general mechanic who spent hours diagnosing it and was able to discover it was a shorted wire! He also told me not to buy MItsubishi autos!

Posted on Jun 08, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Great, dont buy mitsubishi

Posted on Nov 03, 2012

3 Suggested Answers

bigc73542
  • 108 Answers

SOURCE: trns shift problem

On chrysler product vehicles that use the electrical solonoids inside the trans oil pan can usually just be removed and cleaned and they will usually function correctly again. They have a tendency to get laquered up and stick if the trans fluid has not been serviced regurarly. This happenes from the neon all the way up to the dodge 3/4 ton pickups with the gasoline engines.

Posted on May 04, 2009

SOURCE: Geeting the DTC 755 Shift Solenoid B Malfunction -

its inside the transmission.

Posted on Nov 27, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bad transmition, the car wonte will not go in drive or reverse, just revs up real high


code p0743 refers to torque converter clutch solenoid-electrical=== causes wiring--clutch solenoid ECM/TCM
code p0750 refers to shift solenoid--A circuit malfunction=== causes wiring --- shift solenoid --ECM/TCM
code p0755 refers to shift solenoid B --circuit malfunction=== causes -- wiring---shift solenoid ---ECM/TCM
First is to check the wiring and connections are in good condition. next is to replace the clutch solenoid for the torque converter and work up from there

Jun 06, 2013 | Mazda 626 Cars & Trucks

1 Answer

What are these codes in toyota rav 4 PO171 PO105 PO760 PO 770 PO130 PO171


OBD=11
code p0171 refers to system to lean---causes ---intake/ exhaust leak---air system---MAF/VAF sensor---fuel pressure/ pump---injectors HO2s
code po105 refers to manifold absolute pressure (MAP) sensor/bar ometric sensor and circuit malfunction causes---wiring---MAP sensor ECM
code p0760 refers to shift solenoid--circuit malfunction causes--shift solenoid---ECM?TCM
code po770 again refers to shift solenoid.
code p0171 again refers to shift solenoid ---performance or stuck off.
code po130 refers to heated oxygen sensor HOS2 1 bank 1-circuit and have the rest checked .malfunction -- causes---heating inoperative---poor connection---wiring--- HO2S. So replace the shift solenoid and oxygen sensor

Apr 22, 2013 | 1996 Toyota RAV4

1 Answer

O/d light blinks when driveing o/d seems to be engaged car has 198000 miles and runs very good also engine light is on


O/D light blinks, but with that the check engine light is ON.--- This will make your troubleshooting easier.When the check engine light comes on, and remains on, this indicates that there is error stored in your cars computer.---- Once the computer is scanned, you will get error codes, as per that error code it will point towards faulty part, which is causing the O/D light to blink.-------- Most probably the O/D light blinks, If a problem exists in No. 1 or No. 2 solenoids or speed sensors .
--------------- For car after 1995 it requires OBD2 tool and for car before 1995 it requires OBD1 tool.------- --------- You car will require OBD1 tool.There are very few auto parts store and repair centers who have OBD1 tool.In your case you required OBD1 tool.------ You can just contact local auto-parts store and they will guide you to the nearest store who has OBD1 tool.There you can get your car scanned.If there is error set in your cars computer, then you will receive the error code.As per error code it will point towards the faulty part causing this problem in your car.------------- -------------- The codes which you get is scanning will be mostly any of this following codes:--- DTC P0500 - Vehicle Speed Sensor Malfunction
. DTC P0750 - Shift Solenoid "A" Malfunction
. DTC P0753 - Shift Solenoid "A" Electrical Malfunction
. DTC P0755 - Shift Solenoid "B" Malfunction
. DTC P0758 - Shift Solenoid "B" Electrical Malfunction
. DTC P0770 - Shift Solenoid "E" (SL) Malfunction
. DTC P0773 - Shift Solenoid "E" (SL) Electrical Malfunction
. DTC P1520 - Stop Light Switch Signal Malfunction
. DTC P1705 - Direct Clutch Speed Sensor Circuit Malfunction
. DTC P1765 - Shift Solenoid Valve SLN Circuit Malfunction
. DTC P1780 - Park/Neutral Position Switch Malfunction
--------------- Now it all depends on what code you get, as per that you can replace the following part.------- This will help.Thanks.Helpmech.

Jul 07, 2011 | 1995 Toyota Camry

1 Answer

My c6 in bronco starts off in 2nd gear performs ok every other way.


P0700 Transm.Contr.System Malfunction 17084
P0702 Transm.Contr.System Electrical 17086
P0703 Torque Converter/Brake Switch B Circ Malfunction 17087
P0705 Transm.Range Sensor Circ.(PRNDL Inp.) Malfunction 17089
P0706 Transm.Range Sensor Circ Range/Performance 17090
P0707 Transm.Range Sensor Circ Low Input 17091
P0708 Transm.Range Sensor Circ High Input 17092
P0710 Transm.Fluid Temp.Sensor Circ. Malfunction 17094
P0711 Transm.Fluid Temp.Sensor Circ. Range/Performance 17095
P0712 Transm.Fluid Temp.Sensor Circ. Low Input 17096
P0713 Transm.Fluid Temp.Sensor Circ. High Input 17097
P0715 Input Turbine/Speed Sensor Circ. Malfunction 17099
P0716 Input Turbine/Speed Sensor Circ. Range/Performance 17100
P0717 Input Turbine/Speed Sensor Circ. No Signal 17101
P0721 Output Speed Sensor Circ Range/Performance 17105
P0722 Output Speed Sensor Circ No Signal 17106
P0725 Engine Speed Inp.Circ. Malfunction 17109
P0726 Engine Speed Inp.Circ. Range/Performance 17110
P0727 Engine Speed Inp.Circ. No Signal 17111
P0730 Gear Incorrect Ratio 17114
P0731 Gear 1 Incorrect Ratio 17115
P0732 Gear 2 Incorrect Ratio 17116
P0733 Gear 3 Incorrect Ratio 17117
P0734 Gear 4 Incorrect Ratio 17118
P0735 Gear 5 Incorrect Ratio 17119
P0740 Torque Converter Clutch Circ Malfunction 17124
P0741 Torque Converter Clutch Circ Performance or Stuck Off 17125
P0748 Pressure Contr.Solenoid Electrical 17132
P0750 Shift Solenoid A malfunction 17134
P0751 Shift Solenoid A Performance or Stuck Off 17135
P0752 Shift Solenoid A Stuck On 17136
P0753 Shift Solenoid A Electrical 17137
P0756 Shift Solenoid B Performance or Stuck Off 17140
P0757 Shift Solenoid B Stuck On 17141
P0758 Shift Solenoid B Electrical 17142
P0761 Shift Solenoid C Performance or Stuck Off 17145
P0762 Shift Solenoid C Stuck On 17146
P0763 Shift Solenoid C Electrical 17147
P0768 Shift Solenoid D Electrical 17152
P0773 Shift Solenoid E Electrical 17157
P0790 Normal/Performance Switch Circ Malfunction 17174

Dec 20, 2010 | 1985 Ford Bronco

1 Answer

Hi sir, i want some details related to the gear


P0700 Transm.Contr.System Malfunction 17084
P0702 Transm.Contr.System Electrical 17086
P0703 Torque Converter/Brake Switch B Circ Malfunction 17087
P0705 Transm.Range Sensor Circ.(PRNDL Inp.) Malfunction 17089
P0706 Transm.Range Sensor Circ Range/Performance 17090
P0707 Transm.Range Sensor Circ Low Input 17091
P0708 Transm.Range Sensor Circ High Input 17092
P0710 Transm.Fluid Temp.Sensor Circ. Malfunction 17094
P0711 Transm.Fluid Temp.Sensor Circ. Range/Performance 17095
P0712 Transm.Fluid Temp.Sensor Circ. Low Input 17096
P0713 Transm.Fluid Temp.Sensor Circ. High Input 17097
P0715 Input Turbine/Speed Sensor Circ. Malfunction 17099
P0716 Input Turbine/Speed Sensor Circ. Range/Performance 17100
P0717 Input Turbine/Speed Sensor Circ. No Signal 17101
P0721 Output Speed Sensor Circ Range/Performance 17105
P0722 Output Speed Sensor Circ No Signal 17106
P0725 Engine Speed Inp.Circ. Malfunction 17109
P0726 Engine Speed Inp.Circ. Range/Performance 17110
P0727 Engine Speed Inp.Circ. No Signal 17111
P0730 Gear Incorrect Ratio 17114
P0731 Gear 1 Incorrect Ratio 17115
P0732 Gear 2 Incorrect Ratio 17116
P0733 Gear 3 Incorrect Ratio 17117
P0734 Gear 4 Incorrect Ratio 17118
P0735 Gear 5 Incorrect Ratio 17119
P0740 Torque Converter Clutch Circ Malfunction 17124
P0741 Torque Converter Clutch Circ Performance or Stuck Off 17125
P0748 Pressure Contr.Solenoid Electrical 17132
P0750 Shift Solenoid A malfunction 17134
P0751 Shift Solenoid A Performance or Stuck Off 17135
P0752 Shift Solenoid A Stuck On 17136
P0753 Shift Solenoid A Electrical 17137
P0756 Shift Solenoid B Performance or Stuck Off 17140
P0757 Shift Solenoid B Stuck On 17141
P0758 Shift Solenoid B Electrical 17142
P0761 Shift Solenoid C Performance or Stuck Off 17145
P0762 Shift Solenoid C Stuck On 17146
P0763 Shift Solenoid C Electrical 17147
P0768 Shift Solenoid D Electrical 17152
P0773 Shift Solenoid E Electrical 17157
P0790 Normal/Performance Switch Circ Malfunction 17174

Dec 20, 2010 | 2006 Renault Fuego

1 Answer

Just scanned my 1999 300m. It went into safe mode while me wife was driving it home- 2nd gear only. It had a code P1714 and P0700 come up on the scanner. I can't find anything about the P1714.


Definition of Diagnostic Trouble Code P1714 Chrysler: Low Battery Voltage Dodge: Low Battery Voltage Ford: Shift Solenoid A Inductive Signature Jaguar: Shift solenoid A inductive signature malfunction Jeep: Low Battery Voltage Lincoln: Shift Solenoid A Inductive Signature Mazda: Shift Solenoid '1' Mechanical Fault Mercury: Shift Solenoid A Inductive Signature Subaru: Throttle position sensor power circuit for automatic transmission
Definition of Diagnostic Trouble Code P1714 Chrysler: Low Battery Voltage Dodge: Low Battery Voltage Ford: Shift Solenoid A Inductive Signature Jaguar: Shift solenoid A inductive signature malfunction Jeep: Low Battery Voltage Lincoln: Shift Solenoid A Inductive Signature Mazda: Shift Solenoid '1' Mechanical Fault Mercury: Shift Solenoid A Inductive Signature Subaru: Throttle position sensor power circuit for automatic transmission
Definition of Diagnostic Trouble Code P1714 Chrysler: Low Battery Voltage Dodge: Low Battery Voltage Ford: Shift Solenoid A Inductive Signature Jaguar: Shift solenoid A inductive signature malfunction Jeep: Low Battery Voltage Lincoln: Shift Solenoid A Inductive Signature Mazda: Shift Solenoid '1' Mechanical Fault Mercury: Shift Solenoid A Inductive Signature Subaru: Throttle position sensor power circuit for automatic transmission
That code is low battery voltage on a chrysler

Jun 12, 2010 | Cars & Trucks

1 Answer

Code p0750'p0755,p0765 and misfire when put in drive 1500 rpm


P0750 has to do with the Shift solenoid A its a circuit malfunction. Could be related to or caused by the wiring, shift solenoid, or ECM/TCM.

P0755 is also a shift solenoid B issue Circuit malfunction. Possible causes are wiring, shift solenoid, ECM/TCM.

P0765 is also a fhist solenoid D issue Circuit malfunction. Possible causes are in wiring, shift solenoid or ECM/TCM.

Misfire could be result of not shifting right and making vehicle seem as if there is a misfire but only a suggestion. But either way sounds as if you need to consult with a shop that can run tests with computer on transmission issues first.


Dec 01, 2009 | 1998 Ford Ranger SuperCab

1 Answer

P0740, p0753, p0758, p0785, p1860 all of them lit up on me


PO740 IS TCC SOLENOID CIRCUIT MALFUNCTION CONDITIONS.CHECK TRANSMISSION FUSE - PO753 IS A/T 1-2 SHIFT SOLENOID CIRCUIT MALFUNCTION CONDITIONS.THE 1-2 SHIFT SOLENOID HAS FAILED - PO 758 IS A/T 2 -3 SHIFT SOLENOID CIRCUIT CONDITIONS. CHECK THE ERLS FUSE - PO1860 IS TCM PWM SOLENOID CIRCUIT MALFUNCTION CONDITIONS.CHECK TRANSMISSION FUSE+ IGNITION FUSE.

Aug 02, 2009 | 2002 Dodge Ram Maxi

2 Answers

2002 Kia Sedona XL suddenly downshifts


What was the codes exactly that Auto Zone gave you.??? it might just be a simple wire harness that may have gone loose since you did some work on the speed sensor.
Here are the trouble codes for your car.  Good Luck and get the car scanned again for a more define information.

P0751 Shift Solenoid A Performance or Stuck Off

P0752 Shift Solenoid A Stuck On

P0753 Shift Solenoid A Electrical

P0754 Shift Solenoid A Intermittent

P0755 Shift Solenoid B Malfunction

P0756 Shift Solenoid B Performance or Stuck Off

P0757 Shift Solenoid B Stuck On

P0758 Shift Solenoid B Electrical

P0759 Shift Solenoid B Intermittent

P0760 Shift Solenoid C Malfunction

P0761 Shift Solenoid C Performance or Stuck Off

P0762 Shift Solenoid C Stuck On

P0763 Shift Solenoid C Electrical

P0764 Shift Solenoid C Intermittent

P0765 Shift Solenoid D Malfunction

P0766 Shift Solenoid D Performance or Stuck Off

P0767 Shift Solenoid D Stuck On

P0768 Shift Solenoid D Electrical

P0769 Shift Solenoid D Intermittent

P0770 Shift Solenoid E Malfunction

P0771 Shift Solenoid E Performance or Stuck Off

P0772 Shift Solenoid E Stuck On

P0773 Shift Solenoid E Electrical

P0774 Shift Solenoid E Intermittent

P0780 Shift Malfunction




May 05, 2009 | 2002 Kia Sedona

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

3,051 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...