Question about 1989 Suzuki Swift

1 Answer

It all started when i put the car in 1st gear when i just start to accelerate the gear disengages pops out of 1st gear. Under car doesnt sound smooth now probs can occur in 1st 2nd and 3rd gear. Dont know if cable needs adjusting, fluid needs topping clutch or gearbox probs.

Posted by on

1 Answer

Check the detent balls in the gear box also check simple things like mounts and clutch adjustment

Posted on Nov 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hydraulic clutch is not disengaging, when put into 1st gear the engine conks out. Replaced the master cylinder and bled the line - still conks out. Do I need too replace the slave cylinder or what?


as per your description problem not clutch since able to start in gear and drive without stall problem sounds more like a fuel delivery not the clutch

Jul 07, 2016 | Cars & Trucks

1 Answer

I installed a complete clutch & Flywheel. I popped outta 1st gear & won't go into any gear whatsoever. Linkage & slave cylinder work! feels like it's going into gear but when i let clutch out nothing


Isolate the problem. Sound like clutch is stuck and not disengaging. Engine off put in gear and rock the vehicle,, with help from a friend press clutch pedal while in gear and have friend push, you will know if the tranny is ok and clutch is stuck. Now check the clutch, slave etc for engagment and disengagment / Clutch linkage- movement/travel may need adjustment or you have something wrong in the reassembly..

Feb 08, 2016 | Cars & Trucks

1 Answer

Cant shift? reverse grinds? and pressure in clutch is low


What you describe sounds very much like the clutch is failing to disengage.
Fluid level being fine and no leaks under the car is good, but doesnt mean there isnt something wrong with either the master cylinder, slave cylinder, or the associated parts.

Highly unlikely there is a fault with the flywheel or clutch as failures with these would normally give no drive in any gear.

Oct 03, 2009 | 1994 Chevrolet Camaro

1 Answer

1st gear doesnt work


new computer that controls it all ,dealer only by the sound of it

Aug 22, 2009 | 2006 Pontiac G6

1 Answer

It sometimes doesnt have enough power to run when I shiftinto 1st


sounds to me like you need tune-up. new plugs perhaps new plug wires.

Jun 27, 2009 | 1995 Volkswagen Jetta

1 Answer

Mazda 6 2.3 petrol 2002 if i select 1st gear too quickly it crunches in but if i put it in easy teres no problem it only happens in 1st gear and i put a new clutch in after the problem started and its...


1st gear syncromesh Is worn or broken. This usually is caused by forcing lever in when clutch is not disengaging fully, or changing gear with out disengaging clutch.
MMP

Aug 14, 2008 | Mazda MAZDA6 Cars & Trucks

1 Answer

Hard shift and blinking overdrive


The blinking overdrive button is telling u that a serious fault has occurred in the electronic controls or a mechanical fault such as excess slippage is occurring.

Jul 16, 2008 | 2000 Ford Ranger SuperCab

3 Answers

1987 Honda Accord Automatic Jolts in 2nd Gear


You need to change the clutch pads on the cars for a smoother drive...............

May 16, 2008 | 1987 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

290 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...