Remove and replace power steering pump xj8 - XJ8 Jaguar Cars & Trucks

All you do is take off pump drive pulley (3) bolts, remove upper radiator hose off of radiator, upper cooling transmissiion line to give you more room and two bolts hold on the pump. Remove high pressure hose and reservoir hose

In relation to these problem there are few solved help links,i suggest you to go through the list and click the required link:-----

Power Steering going out? http://schematicsdiagram.blogspot.in/2012/04/power-steering-going-out.html

---------------
How to Replace power steering pump on Chevy silverado 2500 HD? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pump-on.html
--------------- How to replace Power steering rack and pinion gear on Chevy Silverado 2500 HD? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-rack-and.html
------------- Power Recirculating Ball Steering Gear removal on Chevy silverado 2500 HD? http://technoanswers.blogspot.in/2012/02/power-recirculating-ball-steering-gear.html
----------- Chevy Silverado 2500 HD steering wheel replacing Procedure? http://technoanswers.blogspot.in/2012/02/chevy-silverado-2500-hd-steering-wheel.html
----------- Steering Wheel Locked? http://schematicsdiagram.blogspot.com/2011/12/steering-wheel-locked.html

---------------
How to Remove Power steering Pressure Hose on Dodge Stratus http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-power-steering-pressure.html

------------
How to replace power steering pump on Mitsubishi Diamante?

http://howtobyme.blogspot.com/2012/01/how-to-replace-power-steering-pump-on.html

---------------
How to bleed power steering pump on Toyota? http://repairhelpcenter.blogspot.in/2012/02/how-to-bleed-power-steering-pump-on.html

---------------

----------How to replace power steering pump on Toyota Land cruiser?

http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-power-steering-pump-on.html

-----------
Steering service light ON GMC Sierra Denali?

http://technoanswers.blogspot.in/2012/02/steering-service-light-on-gmc-sierra.html

---------
Steering service light came on 2004 Pontiac Grand Prix

http://technoanswers.blogspot.in/2012/02/on-one-my-pontiac-grand-prix-relatred.html

----------
Check power steering message on Toyota?

http://schematicsdiagram.blogspot.in/2012/02/check-power-steering-message-on-toyota.html

-------
How to remove power steering pulley on 2002 Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/how-to-remove-power-steering-pulley-on.html
---------1992 Ford Aerostar Power steering and Alternator belt routing diagram? http://carbeltrouting.blogspot.com/2011/12/1992-ford-aerostar-power-steering-and.html

----------------
How to replace Power Steering Pump on Acura Car Models?

Also bleeding:

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

--------------

How to replace Steering Linkage on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-linkage-on.html

---------------
How to replace power steering pressure hose on mustang? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-pressure.html

-------------
STEERING SQUEAKS http://alltypesofpartsreplacing.blogspot.com/2012/10/steering-squeaks.html
----------- Steering Column Diagram For 1990 Jeep Wrangler http://schematicsdiagram.blogspot.in/2012/07/steering-column-diagram-for-1990-jeep.html
------------- How to replace Steering Wheel on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-steering-wheel-on-acura.html

------------
How to replace Power Steering Pump on 1999 Acura TL?

http://howtobyme.blogspot.com/2011/11/how-to-replace-power-steering-pump-on.html

-------------

These details will help.

Thanks.

it is well common on jaquar to have power steering oil leak. Especially the leak is from power steering pump. You have to visit a qualified workshop and do the job by renewing the pump. Get on WWW.ebay co.uk or usa and surely you will find a good price pump new.

Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.




*This originally came from abauto

Most power steering pumps are driven by the serpentine belt and should be in plain view when the hood is open.The following shows how to remove and replace the power steering pump and might give you a clue if not in plain sight. My dad's 1998 Ford Taurus has it nearly on top, but they could have changed things in the mean time: Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:

1. Before servicing the vehicle refer to the precautions at the beginning of this section.
2. Disconnect the battery ground cable.
3. Remove the accessory drive belt.
4. Remove the alternator.
5. Drain and remove the radiator coolant recovery reservoir.
6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
7. Remove the idler pulley from the power steering pump support.
8. Remove the belt tensioner.
9. Remove the bracket mounting bolt located under the belt tensioner mounting.
10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
11. Clamp the pump support bracket in a suitable vise.
12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.

To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.
Power steering pump special tools

1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
4. Install the bracket mounting bolt located under the belt tensioner mounting.
5. Install the belt tensioner.
6. Install the idler pulley to the power steering pump support.
7. Connect the hydraulic pressure and return lines.
8. Install the radiator coolant recovery reservoir.
9. Install the alternator.
10. Install the accessory drive belt.
11. Fill the power steering reservoir with power steering fluid.
12. Connect the battery ground cable.
13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.

Power Steering Pump (4V) and SHO To Remove:

1. Before servicing the vehicle refer to the precautions at the beginning of this section.
2. Disconnect the battery ground cable.
3. Remove the accessory drive belt.
4. Drain and remove the radiator coolant recovery reservoir.
5. Position a drain pan under the power steering pump. Disconnect the power steering pump reservoir hose and allow it to drain.
6. Using Pulley Remover T69L-10300-B, or equivalent, remove the pulley from the power steering pump shaft.
7. Disconnect the pressure hose from the power steering pump and allow it to drain.
8. Remove the power steering pump retaining bolts and the pump.

To Install:

1. Install the power steering pump and tighten the bolts 15–22 ft. lbs. (20–30 Nm).
2. Connect the pressure hose and secure the clamp.
3. Using a Steering Pump Pulley Replacer T65P-3A733-C, or equivalent, install the power steering pump pulley: the pulley face must be flush with the pump shaft or within 0.010 inch (0.25mm).
4. Connect the power steering pump reservoir hose.
5. Install the radiator coolant recovery reservoir.
6. Install the accessory drive belt.
7. Fill the power steering reservoir with power steering fluid.
8. Connect the battery ground cable.
9. Start the engine and check for leaks and proper operation. Bleed the power steering system if needed.

Hopfully this will be ALL you need Besides Pulley REMOVAL TOOL It can be Rented @ AutoZONE

REMOVAL

1. Remove drive belt.
2. Raise vehicle on hoist. WARNING: TURN AIR SUSPENSION SWITCH (LOCATED IN LUGGAGE COMPARTMENT) OFF TO PREVENT VEHICLE DAMAGE OR PERSONAL INJURY.
3. Remove power steering pressure hose bracket.
4. Disconnect electrical connector at power steering control valve actuator.
   1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley hub. CAUTION: Do not apply in-and-out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.
   2. Hold the small hex-head and rotate the tool nut counterclockwise to remove the power steering pump pulley.
   3. Disconnect power steering pressure hose at power steering pump and drain fluid into a container.
   4. Disconnect power steering return hose at power steering pump and drain fluid into a container.
   5. Remove four retaining bolts and power steering pump and power steering pump pulley assembly.
   6. Remove power steering pressure switch from pump.
   INSTALLATION
   
   1. Position the power steering pump on the mounting bosses of engine block and install the bolts at the side of the power steering pump. Tighten to 20-30 Nm (15-22 ft. lbs.).
   2. Connect the power steering reservoir pump hose to the power steering pump and reposition the hose clamp to power steering pump inlet fitting.
   3. Replace power steering pressure hose O-ring.
   4. Install the power steering pressure hose to the power steering pump fitting. Tighten the tube nut with a tube nut wrench rather than with an open-end wrench. Tighten to 34-46 Nm (26-33 ft. lbs.). NOTE: Swivel or end play of the power steering pressure hose end is normal and does not indicate a loose fitting.
   5. Place the power steering pump pulley on the power steering pump shaft and install Power Steering Pump Pulley Replacer T91P-3A733-A. The small diameter threads on the tool should be engaged in the power steering pump shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group.
   6. Hold the small hex-head and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group. NOTE: The power steering pump pulley face must be flush within 0.25 mm (0.010 inch) of the end of the pump shaft.
   7. Remove the Power Steering Pump Pulley Replacer T91P-3A733-A.
   8. Remove the shipping tube nut from power steering pump housing prior to installation.
   9. Connect electrical connector to power steering control valve actuator.
   1. Install power steering pressure hose bracket.
   1. Lower the vehicle.
   2. If equipped, turn the air suspension ON.
   3. Install drive belt on the power steering pump pulley.
   4. Fill the power steering pump reservoir with Power Steering Fluid Motorcraft MERCON(r) ATF.

You might need a lube job or you may need to see if noise is coming from another place such as your engine water pump, brakes, power steering. Look for leaks.

2004 Pontiac Grand Prix V6-3.8L VIN 2

Power Steering Pump: Service and Repair
Power Steering Pump Replacement
NOTE: The content of this article / image reflects the changes called out by TSB: 05-02-32-004.

Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

not too hard if you have some tools.

1. Raise and support the vehicle.
   

1. Remove the power steering pump pulley (3A733). Refer to the procedure in this section.
   

1. Place a drain pan under the power steering pump (3A674).
   

1. Remove the power steering pressure hose bolt from the power steering pump. Place the power steering pressure hose (3A719) up and out of the way.
   
2. Remove the two power steering reservoir pump hose bolts. Place the power steering reservoir pump hose up and out of the way.
   
3. Remove the three front power steering pump bolts.
   
1. Remove the rear power steering pump bolt.
   
1. Remove the power steering pump from the vehicle.