Question about 1988 Mazda B2200

2 Answers

Knocking at 2 to 3 thousand rpms

I have a 1991 mazda b2200 2.2 carb with about 170,000 on it. it recently started to smoke so we went ahead and put new oil seals,piston rings and rod bearings in we put it back together it starts up just fine idles fine but when it gets warm the oil light comes on and starts to knock when it reaches 2,000 rpm when you let it go down to a idle it stops the car drives just fine but just knocks and the oil light comes on and theres enough oil in it please help i was recently laid off and have no other option but to do it myself

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

When you put the eng back together did you put a new oil pump in it when you put it back together... the pump might be week

Posted on Jan 03, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 426 Answers

If you didnt have the crank ground or the rods resized and over sized bearings instaled then the issue with your engine is beyond advice other than remove engine and rebuild correctly as there is too much clearance and the oil cannot build enough pressure especialy when hot as it thins out and becomes harder to maintain pressure.Your problem is crankshaft bearings have excessive clearances or oil pumps pressure relief valve is jammed/jamming.good luck and hope its just the pump.

Posted on Nov 04, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My little truck smokes to bad to drive , what is the problem


Given the 22 year vehicle age I would let it go to
truck heaven

Motor is worn out as you know

Rings,valve guides,valve seals
not worth fixing

Mar 02, 2013 | Cars & Trucks

1 Answer

What is the gap setting on the spark plugs. please, 1991 mazda b2200


1992 MAZDA B2200 L4 - 2.2L - FI - - GAS

Part Number RN12YC - .035"

Hope this help (remember rated this) Good luck.

May 15, 2010 | 1988 Mazda B2200

1 Answer

Need a heater core diagram for a 91 mazda b2200


The only thing to do is get a diagram from the MAZDA dealer parts dept. "A few parts fell out" is way to vague to help you.

Dec 30, 2009 | 1991 Mazda B-Series

2 Answers

1993 Mazda B2200 smokes blue smoke for 2 min.on start up only after setting overnite. does not smoke otherwise.Replacing valve guide seals did not help. compression test is good.What is the problem?


The oil rings on the pistons may be stuck, gummed up. I would remove the spark plugs and and see if you can find some Combustion Chamber Cleaner or some other type of cleaner that will cut carbon and oil sludge. Put about .5 oz in each cylinder over night and in the morning spin the enigne over a few timers and then replace the plugs and go drive it a few miles. That may get the rings unstuck.

Nov 13, 2009 | 1988 Mazda B2200

1 Answer

Price on a 1991 B2200 Mazda Pickup truck carburetor


Depends if you want new or used, Location, and a few other variables

Jun 04, 2009 | 1988 Mazda B2200

1 Answer

Morning starts off shaken rough and smokes(mazda b2200)


Check the tires for a lump outside or even unbalance you may also want to check for over inflation of air

Mar 24, 2009 | 1988 Mazda B2200

2 Answers

87 mazda b2200


if it wont hold an idle then one or more of the cylinders are probably too low or high in compression and if it's backfireing then the ignition timming could be off. I would take a compressin test of all cylenders and if they are all in range I would hook up a timming light to se if the timming is out

Jul 02, 2008 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

283 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...