Question about 2005 Hyundai Tiburon

1 Answer

2005 Huyndai Tiburon Brake Replacement

ON the rear brake pads on this vehicle...How do we retract the caliper?

Posted by on

  • Anonymous Mar 21, 2014

    unable to reassemble due to rear brake cylinder partial

  • Anonymous Mar 25, 2014

    when braking the rear wheal keeps moving even after i had changed all rear system

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 566 Answers

Hi assume you wish to fit new pads ? if so the the rear caliper pistons are not as front calipers just push back you have to wind back the pistons whilst applying pressure to piston there is a tool specially for this purpose which saves time and effort cheapest un uk is the one made by draper tool Co see motor stores? however! you can improvise and manually wind pistons back using the U shape spanner with 2x prongs that is commonly used/supplied to circular saws and this is spanner for changing blades ? does the trick if you have or can borrow one? look at pistons and you will see where tool locates you just turn c/wise and press piston as you do and it will retract have a little patience! the most important tool in the box that money can't buy ! hope this helps best wishes from uk

Posted on Nov 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size allen wrench do i need for the front brake calipers


For front brake pads replacement you only need usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
Instructions for front brake pads replacement.
For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing.

Important note: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!!
Check brake fluid level and top up as neccessary!

Sep 03, 2011 | 1994 Audi 100

1 Answer

How to collapse rear calipers on 2005 free star ford


Open bleed valve,use a piston tool, to
turn parking brake in,as you push piston
back into caliper

The piston should screw in clockwise
That is the parking brake feature
The piston also has to be retracted ,as on the front

After the pads are on, ratchet up the P-Brake
to tighten pad clearance

You don't need to open bleeder, but it is easier,
and you absolutely have to flush brake fluid on ALL
vehicles every 2 years

Dec 19, 2010 | Ford Freestar Cars & Trucks

1 Answer

How to replace rear breaks on 2005 f350 super duty dually


Rear To Remove:
  1. Remove the brake master cylinder filler cap and remove fluid until the reservoir is half full.
  2. Raise and safely support the vehicle.
  3. Remove the rear wheel and tire assembly. CAUTION
    Never allow the brake caliper to hang from the brake hose.
  4. Remove the two disc brake caliper pin bolts.
  5. Lift the disc brake caliper from the anchor plate and position the caliper out of the way. Do not disconnect the fluid line.
  6. Inspect the disc brake caliper for leaks and replace the caliper if necessary.
  7. Remove the pads and retraction clips.
To Install:
CAUTION
Do not allow grease, oil, brake fluid or other contaminants to contact the pad lining material.
  1. Install retraction clips.
  2. Install the brake pads.
  3. Slowly compress the caliper pistons with a large C-clamp. CAUTION
    Use care not to damage the bleeder screw or front disc brake rotor shield.
  4. Install the disc brake caliper.
  5. Install the disc brake caliper pin bolts. Tighten the pin bolts to 26 ft. lbs. (35 Nm) (F-250, F-350 SRW). Tighten the pin bolts to 56 ft. lbs. (76 Nm) (F-350 DRW). Tighten the pin bolts to 46 ft. lbs. (62 Nm) (F-450 F-550).
  6. Install the wheel and tire assembly.
  7. Lower the vehicle.
  8. Fill the brake master cylinder reservoir with DOT 3 motor vehicle brake fluid.
  9. Inspect for correct brake operation.

Jul 06, 2010 | 2005 Ford F 350 Super Duty

1 Answer

2006 Kia Spectra 5 rear brake disc replacement


One side,turns right,and push in slightly,and the other side turns left,to retract.

Apr 20, 2010 | 2007 Kia Spectra5

3 Answers

Changing the front brake pads on a 2006 Pontiac Montana SV6


no that is only the older rear calipers on gm and others. the fronts do not have that style caliper and sound like the calipers are frozen and may be way your changing the pads. try opening the bleeder screw and then compressing them if they go then you need need brake hoses and if not you need calipers. god luck man

Dec 13, 2009 | 2005 Pontiac Montana SV6

3 Answers

How do you push in the cylinder in rear brakes to change pads on a 2005 tiburon


The Tiburon's rear disk brakes are self-adjusting to compensate for pad wear. You need to twist the piston clockwise to retract it into the caliper. You should do this using a special tool from Hyundai. Alternatively, you can get generic rear brake caliper tool at most auto parts stores that you can use on the end of your ratchet.

Or, you can be really careful with a pair of channel-lock pliers and grip the edge of the piston, allowing you to twist it back into the caliper.

Nov 14, 2009 | 2005 Hyundai Tiburon

1 Answer

Brake pad replacement


Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Front wheels
  3. Place a C-clamp over the caliper as illustrated, place a screw drive head against the outboard pad and hook against the rear of the caliper. Slowly tighten the screw drive and retract the caliper pistons into their bores and breaking the outboard brake pad from the caliper fingers.
  4. Once the pad is free, slide the caliper in on the guides to provide clearance between the rotor and inboard pad.
  5. Place an appropriate prytool through the center opening in the top of the caliper behind the inboard pad between the pistons using care not to contact the piston boots. Pry the pad to free it from the pistons.
  6. Remove the two caliper guide pin bolts and position the caliper aside. Remove the brake pads.
ff17c9d.gif
Place a C-clamp over the caliper as illustrated

b802acb.gif
View of the caliper guide pins and boots (1), anti-rattle clips (2), brake rotor (3), outboard pad (4), caliper adapter (5) and inboard pad (6)

To install:
  1. Completely compress the caliper pistons
  2. Install or connect the following:
    • Brake pads with anti-rattle clips onto the adapter
    • Caliper and align the guide pin bolt holes with the guide pins. Install the pin bolts and tighten to 32 ft. lbs. (43 Nm).
    • Banjo bolt with new washers on each side of the hose fitting and tighten to 35 ft. lbs. (47 Nm)
    • Wheels
    • Negative battery cable
  3. Check and adjust the brake system fluid level and road test the vehicle.

Nov 01, 2009 | 2005 Chrysler Pacifica

1 Answer

How do i replace front pads on 2005 chrysler pacifica


PLEASE DON'T FORGET TO RATE!!!!

Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Front wheels
  3. Place a C-clamp over the caliper as illustrated, place a screw drive head against the outboard pad and hook against the rear of the caliper. Slowly tighten the screw drive and retract the caliper pistons into their bores and breaking the outboard brake pad from the caliper fingers.
  4. Once the pad is free, slide the caliper in on the guides to provide clearance between the rotor and inboard pad.
  5. Place an appropriate prytool through the center opening in the top of the caliper behind the inboard pad between the pistons using care not to contact the piston boots. Pry the pad to free it from the pistons.
  6. Remove the two caliper guide pin bolts and position the caliper aside. Remove the brake pads.
24539c8.gif
Place a C-clamp over the caliper as illustrated

6ccd8b6.gif
View of the caliper guide pins and boots (1), anti-rattle clips (2), brake rotor (3), outboard pad (4), caliper adapter (5) and inboard pad (6)

To install:
  1. Completely compress the caliper pistons
  2. Install or connect the following:
    • Brake pads with anti-rattle clips onto the adapter
    • Caliper and align the guide pin bolt holes with the guide pins. Install the pin bolts and tighten to 32 ft. lbs. (43 Nm).
    • Banjo bolt with new washers on each side of the hose fitting and tighten to 35 ft. lbs. (47 Nm)
    • Wheels
    • Negative battery cable
  3. Check and adjust the brake system fluid level and road test the vehicle.

Nov 01, 2009 | 2005 Chrysler Pacifica

2 Answers

Brake Pad Replacement,2004 VW Touareg,V6 instructions


yes, you need a piston retract tool for the rear cylinders. rear piston must turn clockwise as it is being retracting.

Jun 11, 2009 | 2004 Volkswagen Touareg

1 Answer

Rear brake pad installation 99 volkswagen passat


If you can't see diagrams(sometimes happens) let me know and I will get them to you

  1. Raise and support the vehicle. Remove the rear wheels.
  2. If equipped, disconnect the brake pad wear sensor from the harness.
  3. Counterhold the lower sliding pin using a thin open-end wrench and remove the caliper-to-sliding pin hex bolt.
  4. Pivot the caliper upward or if necessary remove the upper caliper-to-sliding pin hex bolt.
  5. Using a brake caliper retraction tool, select the appropriate sized piston press arbor and install the tool onto the brake caliper. Following the tool manufacturer's recommendations, use the tool to rotate the caliper piston clockwise as it is pressed into the brake caliper housing, until it is fully retracted.
0900c152800c30b8.jpgUse a thin open-end wrench to . . . 0900c152800c30b7.jpg. . . support the caliper sliding pin when removing the caliper mounting bolt 0900c152800c30d7.jpgUse a disc brake caliper piston retracting tool that will rotate the caliper piston as it is pressed into the caliper 0900c152800c30d8.jpgThe rear caliper piston is slotted to allow a retracting tool to rotate the piston when replacing the brake padsTo install:
  1. Clean the brake caliper and all sliding surfaces. With the caliper piston pressed fully back into the caliper housing, check for leaking fluid and damaged dust boots.
  2. If equipped, install a new brake pad wear sensor in the pad if the plastic part has been worn through on the old sensor. New sensors are not required unless the wire inside the plastic part has been exposed.
  3. Lubricate the slider bolts with approved brake grease.
  4. Install the brake pads onto the bracket assembly, and then carefully lower the caliper over the caliper mount. Check and make sure that the pad springs are correctly seated.
  5. Replace all removed caliper-to-sliding pin bolts and torque to:
  6. 1990-97 Passat models: 25 ft. lbs. (35 Nm)
  7. 1998-00 Passat models: 22 ft. lbs. (30 Nm)
  8. If equipped, connect the brake wear sensor wire to the harness. Check for a good connection as most problems with the sensor circuit are caused by faulty connections. Check that the wire is held by the loop in the dust cover and the connector is held at the clips.
  9. Install the wheels and hand tighten the lug bolts. Lower the vehicle carefully until the tires begin to contact the surface and torque the lug bolts to specification in a crisscross pattern to:
  10. M12 x 1.5 lug bolts: 81 ft. lbs. (110 Nm)
  11. M14 x 1.5 lug bolts: 89 ft. lbs. (120 Nm)
Feel free to contact if you have any questions

Nov 15, 2008 | 1999 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

918 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...