Question about Peugeot Liberte

1 Answer

Where is the egr valve on a 307 - Liberte Peugeot Cars & Trucks

Posted by on

  • ddonq Nov 20, 2008

    where is the egr valve on a 206

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 99 Answers

They can be located in a number of places. one way to locate is look for a corrigated metal pipe, it is about an inch in diameter and will come from the exhaust manifold area and travel up to the inlet manifold. The valve is usually the cylindrical object on the inlet manifold where the pipe meets.
It will have a wiring plug going into it.

Posted on Jan 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My parisienne back fires in the engine sometimes when I am quick accelerating the engine. what causes this?


it can be ignition timing off a little, it could be lack of fuel under acceleration, worn timing chain, EGR valve opening too soon causing a lean condition.

Jul 28, 2015 | 1986 Pontiac Parisienne

1 Answer

Peugeot 307 fault codes


code p2144 refers to exhaust gas recirculation (EGR) vent control--circuit low===causes wiring short to ground--EGR vent control.
Check the condition of the wiring and if ok then replace the vent control

May 11, 2014 | 2005 Peugeot 307 1.4

1 Answer

Have a 1998 cadillac eldorado, diagnostic codes are PO404 and PO307, what does that mean?


Code 404 is for a problem with the EGR valve and code 307 is for a miss on cylinder 7.
The egr valve would need to be tested, and the spark plug and injector checked out on cylinder 7.

Jan 10, 2013 | 1998 Cadillac Eldorado

1 Answer

Ford Explorer : How to Troubleshoot the EGR P0401 Trouble Code


P0401 - Exhaust Gas Recirculation Flow Insufficient Detected

Possible Causes:
- Harness or connectors (EGR volume control valve circuit is open or shorted.)
- EGR volume control valve stuck closed
- EGR volume control solenoid valve
- Dead (Weak) battery
- EGR passage clogged
- Exhaust gas leaks
- Faulty EGR valve

Possible Solutions:
- Clean EGR Valve
- Replace EGR Valve
- Repair EGR harness or connector
- Replace EGR volume control solenoid valve
- Replace EGR volume control valve

Jan 24, 2011 | Ford Explorer Cars & Trucks

3 Answers

Location of EGR valve for 4.6 liter engine? how do you remove the EGR valve?


a887903.gif
EGR VALVE IS #2.

Please wait for second post to answer your second question....comes with a few pictures.

Nov 16, 2009 | 1992 Ford Crown Victoria

1 Answer

Hi, my 307 hdi 2.0 79kw, accelerate to slow, my


Clean/Change air filter, fuel filter, air filter, turbo filter. Clean and check EGR valve and Turbo gate. Check the hdi fuel pressure. Open the injectors and clean it. Give it a try and may be you can save 600 euros.

Oct 17, 2009 | 1987 Peugeot Liberte

1 Answer

I searched online to find a way to eliminate pinging on the 307 olds engine and found a site saying by removing the carb and drilling out the egr ports to remove carbon buildup as well as cleaning the egr...


Well the pinging you hearing could be detonation try premiun fuel or try retarding the timing by a couple of degrees. do not drill out the ports. it won't fix it. don't believe everything you read online please. hope this helps you out!!

Jul 09, 2009 | 1986 Cadillac Fleetwood

2 Answers

2005 Dodge 1500 code p0404 EGR valve.


The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Feb 05, 2009 | 2005 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

519 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...