Question about 1993 Chevrolet S-10 Blazer

1 Answer

1991 chevy s10 blazer

I have a 1991 chevy s10 blazer 2door 4x4 that the fuel pump stopped working. I have replaced the fuel pump and it still will not start. I replaced the relay as well and still no luck. Can you advise me as to what else it can be. thanks

Posted by on

  • 5 more comments 
  • kchristie41 Nov 04, 2008

    fues and fule filter ok I am not getting power to the fuel pump,also ground wire looks ok.What els do you think it could be? Thanks for the help

  • kchristie41 Nov 11, 2008

    stll not getting power back to the fuel pump.could it be something to do with the ecm? I checked fues and relay both are working.I sprayed starter fluid into the fuel injection it starts then stalls out.What els could it be.Thanks for any help

  • Anonymous Mar 01, 2009

    1993 blazer, checked fuel pressure from pump will start if primed, vortec motor and will continue to run, but then will not start again without a prime to the throttle body

  • Kody Gould Nov 09, 2012

    Were you able to figure out what the problem was? I have the exact same problem with my 91 chevy s10 blazer.

  • Kody Gould Nov 09, 2012

    Were you ever able to figure out the problem? I have the exact same problem with my 91 chevy s10 blazer.

  • Anonymous Mar 18, 2014

    92 s10 Blazer will not start. I just replaced fuel pump so its getting fuel but no fire.how do find the problem

  • Anonymous Mar 29, 2014

    need to replace the horn but can't locate it

×

1 Answer

Check the fuse under the dash. Did you replace the inline fuel filter? If not, you could loosen the line going into the filter then turn the key to the on position. The pump should run for about 2 seconds then the relay should kick off. Turn off the key for approx. 5 seconds then cycle key back on and the pump should cycle again. If you get a 2 second burst of fuel each time then the pump is cycling. Install a new fuel filter and check the grounded wire by the tank. Hope this helps. :)

Posted on Nov 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 93 chevy s10 4x4 blazer, my instrument panel worked before new motor was put in, after having the new engine put in, my fuel gauge, oil pressure, voltmeter, rpm, and my temp gauge all quit worki


Look for a missing ground strap from the engine to the body or frame. Remember the engine sits on rubber mounts so that ground strap is essential.

Feb 21, 2014 | Cars & Trucks

1 Answer

1997 chevy s10 blazerdash wont light up when key


the dash sound's like a fuse, check the fuse box under the hood and in the door jamb on the side of the dash, also check your fuel filter and fuel pump, im betting on the pump because i have a 2001 chevy blazer that has had two replaced and it has 233000km on it!

Jun 04, 2010 | 1997 Chevrolet Blazer

1 Answer

My chevy s10 blazer will start for a couple of minutes then shut off. It has a new fuel pump, cap & rotor, spark plugs and wires. The computer is putting out a 1-2 code.


the code 1-2 is just telling you that you're in diagnostic mode (means nothing) fuel pump could be going out or fuel filter

Mar 28, 2010 | 1991 Chevrolet S-10 Blazer

3 Answers

1991 Chevy S10 Blazer 4.3 4x4


4170636.jpgThis is all I've got.Hope this helps?

Dec 20, 2009 | 1991 Chevrolet S-10 Blazer

1 Answer

1991 S10 blazer 4x4 4.3 popping coming from the front


the popping sound is the stabilizer links or the lower control arm bushings you can replace all bushings and both link kits for around 50.00 and the light is prob from the sensor on the transfer case or the front end i would remove and clean with dawn dishwashing liquid and put them back.

Jun 23, 2009 | 1991 Chevrolet S-10 Blazer

2 Answers

My 95 chevy blazer fuel preoblem i think


Check the Fuel pump with a presure guage.

Apr 21, 2009 | 1995 Chevrolet Blazer

1 Answer

1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks


have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Mar 11, 2009 | 1997 Chevrolet S-10 Pickup

2 Answers

86 Chevy wont start


check for spark by removing a sparkplug

Dec 31, 2008 | 1986 Chevrolet S-10 Blazer

Not finding what you are looking for?
1993 Chevrolet S-10 Blazer Logo

892 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...