Question about 1998 Chevrolet Cavalier

1 Answer

98 cav z24 factory deck

My keyless remote doesnt work after i took the fac deck out is there a module i can get so it works again ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 70,347 Answers

No other Body Control Module (BCM) is avail for your car, call the maker of the deck and talk to there tech staff about this problem.

Posted on Nov 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

2 Answers

Programming instructions for keyless remote Does anyone have the programming instructions for 1998 honda passport keyless remote (FCC #HYQ1512R)?


Get into your passport and unlock all doors. Leave drivers door open. Put key into ignition. Turn to ON (not start), then OFF three times within 5 seconds. Close and open the drivers door twice. Turn key to ON then OFF 5 times within 5 seconds. Close then open the drivers door. Press either the lock or unlock button on the remote. Doors will lock then unlock. Press the button again. Doors will lock then unlock again. Close door to finish programming. If it doesnt work, try it again but turn the key faster. You have to do it all pretty quick, but I had it done on the second try.

Oct 03, 2009 | 1998 Honda Passport

1 Answer

2001 Chevy cavalier Z24 keyless entry not working.


You should have it scaned to see if you have any codes. It has a RCDLR (remote control door lock reciever) this is the module that recieves the signal from the fobs. If it has a problem then the system will not work. If it has to be replaced then a dealer will have to program it for you. Good Luck

May 25, 2009 | 2001 Chevrolet Cavalier

2 Answers

Program factory remote keyless entry: 2003 Hyundai XG350


The procedures you list require the Hyundai Keyless Remote programming module, which you don't have. This module is proprietary - only Hyundai Dealerships have it. There is a 10 pin connector under the dash (next to the DLC - Data Link Connector) which is used to connect the Keyless Remote Programming Module. This module has two switch positions "Ready" and "SAVE". When the switch is place in the 'SAVE" position, that's when the keyless remotes are activated to send their 'codes' to the Electronic Time and Control System (ETACS). The module's switch is then set to "Ready" and the remote is tested to see if it works properly.

May 22, 2009 | Hyundai Motor 2003 XG350

3 Answers

99 gmc jimmy sle keyless remote and security issue


Hi: From my experience the security issue is easily solved because hitting the factory key FOB lock button is the only way to activate it, hitting door lock button will not activate it. When installing a remote starter no wires are cut usually, just spliced into which means... make sure that where wires were spliced they are taped. If you have the original factory key FOB use a quarter and pop apart, replace the battery, key FOB should have retained its factory setting if your lucky, if doesn't work go to internet search and find programming procedure. Hope this helps... please rate suggestion...ty

Apr 23, 2009 | 1999 GMC Jimmy

1 Answer

I replaced the car battery, now the keyless remote wont work.


look at your service manual the jump is usually in the trunk i i have a cadillac that happened to and you have to reset the codes on the keypads some do not need to be connected but the newer cars do you may just need to follow another series of keyturns and press door locks anymore help let me know i will find the procedure for you

Jan 07, 2009 | 2005 Chevrolet Malibu

2 Answers

1990 Olds 98 Regency Brougham - Programming Keyless Entry


Same car same problem, but I found the plug w/two wires behind the glove box. It is on a brace on the left hand side, has a clip holding it there. Lift up on the clip and it slides off.
I jumpered those two wires, the door locks did not cycle as was in the instructions and remote still doesn't work.
Sounds to me like I'm missing power from somewhere, but where?
Hope you find your wires and they work for you.

Nov 10, 2008 | 1990 Oldsmobile Regency

1 Answer

98 A4 quatro, broken keyless entree system


can you hear the pump trying to work?

Jul 30, 2008 | 1998 Audi A4

Not finding what you are looking for?
1998 Chevrolet Cavalier Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...