Question about 1992 Chevrolet Lumina

1 Answer

92 lumina car crankshaft position sensor

Where is the part located at? Need visuals if possible

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Chevrolet Expert
  • 293 Answers

If its the 3,1 engine it is located at the bottom of the engine near the tansmission very hard to get at has a 8mm headed bolt holding it in place be very carful when pulling it out of engine block as the plastic is very brittle you will need to woork it to get it out in one piece

Posted on Nov 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3.1l. Where is the crankshaft position sensor?


Which one? There are two crankshaft position sensors on the 3.1L.
One is the 24X sensor. It is located behind the crankshaft pulley, installed into the timing cover. The other sensor, the 7X sensor (this is the one that is it fails will cause a no-start condition), is located on the outside of the engine block, close to the crankshaft.

Oct 25, 2015 | 1995 Chevrolet Lumina

1 Answer

Where is crank position sensor on 1991 2.5l


The 1991 was a mid-sized sedan created by Chevrolet in Ontario, Canada. The Lumina is equipped with a crankshaft sensor that detects the position of the vehicle's crankshaft, sending data to the sedan's on-board computer. Having the crankshaft sensor allows the Lumina to make necessary adjustments for the engine to work optimally.

http://www.xcardiag.com/wholesale/vagcom-new-version-release.html

Jul 30, 2014 | Pontiac Grand Am Cars & Trucks

1 Answer

How do I locate crankshaft position sensor 1993 Chevy Lumina Euro


3.1 vin T
3x sensor firewall side of engine above oil pan between transmission
24x sensor behind crank pulley/ balancer

Jan 27, 2014 | 1993 Chevrolet Lumina

1 Answer

Where is the cranking sensor located on a apv lumina 1992 mini van


The 1992 Lumina APV does not have a crankshaft position sensor. If your car has a tachometer in the instrument panel it gets it's "signal" from the ignition coil.

Jan 25, 2011 | 1992 Chevrolet Lumina APV

2 Answers

I can't find the location of the crankshaft postion sensor in my 2000 Hyundai sonata


My online Sonata manual shows these possibilities, but does not identify which applies specifically to 2000 Sonata.
Also, when you talk to the dealership parts counter, you'll need to know whether your 2000 Sonata is (a) 4-cylinder 2.4L MFI DOHC engine, or (b) 6-cylinder 2.5L MFI DOHC engine.
Its easy to tell - just count your spark plug wires.

-- begine excerpt from 2000 Hyundai Sonata Repair guide --

The crankshaft position sensor is located next to the flywheel.
The crankshaft position sensor is located next to the flywheel/torque converter.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The crankshaft position sensor is located on the driver-s side of the vehicle, down by the lower radiator hose.
The crankshaft position sensor is located on the engine near the crankshaft pulley.
The crankshaft position sensor is located at the front of the engine near the timing belt.

--- end excerpt from 2000 Hyundai Sonata repai guide ---

Dec 29, 2010 | 2000 Hyundai Sonata

1 Answer

My 91 lumina goes for 10-12 miles and dies what is going on?


You could have a fuel pump issue,the only way to verify that is to check the pressure when it acts up.Also you may have a ignition problem,some of the possible causes could be crankshaft position sensor,camshaft position sensor,ignition control module.A easy way to verify ignition issue is to use a spark plug tester after the vehicle has stalled.

Feb 07, 2010 | 1991 Chevrolet Lumina

1 Answer

P0336 - misfire - lumina 1997 3.1


po336 on 97 lumina 3.1 is---crankshaft position sensor A ckt range /perf.---this is a bad crankshaft sensor!!!

Aug 26, 2009 | 1997 Chevrolet Lumina

1 Answer

Location of cam positioning sensor for 1991 chev lumina 3.1


On your 1992 Chevrolet Lumina-Sedan/Coupe 3.1L MFI OHV , the Crankshaft Position Sensor is located: clearpixel.gif Under hood, passenger side, lower engine area, passenger side of engine block, mounted front of crankshaft pulley

Nov 30, 2008 | 1992 Chevrolet Lumina

Not finding what you are looking for?
1992 Chevrolet Lumina Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...