Question about 1993 Chevrolet K1500

1 Answer

Heater Core How do I remove the heater core in my pick-up? I've removed all visible screws from the bottom cover and cannot get it apart. Is there more screws next to the fire wall?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 76 Answers

Check the interior and xterior especially on the firewall. there should be 10 to 12 screws also go ahead and take the two heater hoses off. sometime they will be adhesive around the interior of the core housing and it will take a little bit of persuasion. hope this helps:)

Posted on Nov 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Heater core leaking through floor vents.


Bad heater core you will need to replace it. About a 2 hour job, very easy to do:


Remove the HVAC module assembly. Refer to HVAC Module Assembly Replacement.
Remove the HVAC filter cover.
Remove the heater core/evaporator tube seals from the module.
Remove the heater core cover screws (1).
Remove the heater core retaining screws (1).
Remove the heater core retaining straps.
Remove the heater core.
Remove the rubber seals from the inlet/outlet pipes of the heater core.

Installation Procedure

Install rubber seals to the outlet/inlet pipes of the heater core.
Install the heater core to the module.
Install the heater core retaining straps.



Install the heater core retaining screws (1).
Install the heater core cover.



Install the heater core cover screws (1).



Install the heater core/evaporator tube seal from the module.
Install the HVAC filter cover.
Install the HVAC module assembly. Refer to HVAC Module Assembly Replacement.

May 19, 2011 | Cadillac DeVille Cars & Trucks

1 Answer

Heater core replacement. Haynes manual and car have major differences.


Heater core is removed from inside the cabin. About a two hour job. The hardest part is removing the hoses in the engine bay.
In the cabin, remove the beauty panel under the glovebox; remove the glovebox, and move the HVAC controller. The heater housing, or cover is held with two screws, and the core is held with one screw (clamp).
Remove the HVAC module assembly. Refer to HVAC Module Assembly Replacement.
Remove the HVAC filter cover.
Remove the heater core/evaporator tube seals from the module.
Remove the heater core cover screws (1).
Remove the heater core retaining screws (1).
Remove the heater core retaining straps.
Remove the heater core.
Remove the rubber seals from the inlet/outlet pipes of the heater core.

Installation Procedure

Install rubber seals to the outlet/inlet pipes of the heater core.
Install the heater core to the module.
Install the heater core retaining straps.



Install the heater core retaining screws (1).
Install the heater core cover.



Install the heater core cover screws (1).



Install the heater core/evaporator tube seal from the module.
Install the HVAC filter cover.
Install the HVAC module assembly. Refer to HVAC Module Assembly Replacement.

This is the best that I can do for you, hope this works

May 19, 2011 | 1998 Cadillac DeVille

1 Answer

How do i replace a heater core in my 97 blazer


Heater Core Removal & Installation To Remove:
Heater core removal gm-10-00-651.gif

  1. Remove the heater/vent module.
  2. Remove the heater core access cover screws.
  3. Remove the heater core access cover.
  4. Remove the heater core from the heater/vent module
To Install:
  1. Install the heater core to the heater/vent module.
  2. Install the heater core access cover and screws to the heater/vent module.
  3. Install the heater/vent module assembly to the vehicle.
prev.gif next.gif

Dec 19, 2010 | 1997 Chevrolet Blazer

1 Answer

Heater core replacement


Heater Core Removal & Installation To Remove:
Heater core removal gm-10-00-651.gif

  1. Remove the heater/vent module.
  2. Remove the heater core access cover screws.
  3. Remove the heater core access cover.
  4. Remove the heater core from the heater/vent module
To Install:
  1. Install the heater core to the heater/vent module.
  2. Install the heater core access cover and screws to the heater/vent module.
  3. Install the heater/vent module assembly to the vehicle.
prev.gif next.gif

Oct 08, 2010 | 2003 Chevrolet Blazer

2 Answers

How to install a new top and bottom hvac heater hose fitting for a 2002 buick lesabre custom


The hoses are moved by turning them a few degree's, then pulling them off. See diagram below.

658aa5f.gif

Jun 19, 2010 | 2002 Buick LeSabre

1 Answer

How To Replace The Heater Core In A 1997 Ford Thunderbird LX


Heater Core Removal
  1. Partially drain the cooling system.
  1. Remove the tube gasket from the heater core tubes.
  1. Remove four heater core access cover retaining screws and remove the access cover from the A/C evaporator housing (19850).
  1. Remove A/C electronic blend door actuator.
  1. Slide heater core (18476) and seals from the A/C evaporator housing.
Installation
  1. Install the heater core in the A/C evaporator housing with the tube gasket on the outside of the case.
  1. Install A/C electronic blend door actuator as described.
  1. Position the heater core cover on the A/C evaporator housing. Install the four retaining screws.
  1. Refill the cooling system.


    1a302ce.gif




    Item Part Number Description 1 18596 Heater Core Tube Gasket 2 18476 Heater Core 3 18B300 Heater Core Cover 4 390747-S2 Screw (4 Req'd) 5 18N267 Heater Core Cover Seal


    Hope this helps... Cobra

Jun 12, 2010 | 1997 Ford Thunderbird LX

1 Answer

REPLACING HEATER CORE


HEATER CORE REPLACEMENT REMOVAL PROCEDURE 1. Remove the fuel injector sight shield. 2. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling System. 3. Use J 38185 in order to position aside the heater hose inlet and outlet clamps at the heater core. 4. Disconnect the inlet and outlet heater hose from the heater core. 5. Remove the RH Instrument Panel Closeout/Insulator panel. 6. Remove the LH Instrument Panel Closeout/Insulator panel 7. Remove the floor carpet. 8. Remove the rear floor air outlet duct from the holes in the floor reinforcement. 9. Disconnect the rear floor air outlet duct from the heater air outlet cover. 10. Remove the rear floor air outlet duct. 11. Remove the heater air outlet cover screws . 12. Remove the heater air outlet cover heat stakes with a small chisel. 13. Remove the heater air outlet cover from the HVAC module assembly. 14. Remove the heater core cover screws . 15. Remove the heater core cover heat stakes with a small chisel. 16. Remove the heater core cover from the HVAC module assembly. 17. Remove the heater core from the HVAC module assembly. 18. Remove the heater core foam seal (1) from the HVAC module assembly.
INSTALLATION PROCEDURE 1. Install a new heater core foam seal to the HVAC module assembly. 2. Install the heater core to the HVAC module assembly. 3. From the inside of the heater core cover, drill the dimples adjacent to the heat stakes using a 5.5 mm (7/32 in) drill bit. 4. Install the heater core cover to the HVAC module assembly. NOTE: Refer to Fastener Notice in Service Precautions. 5. Install the heater core cover screws . Tighten Tighten all screws to 1.5 N.m (13 lb in) . 6. From the inside of the heater air outlet cover, drill the dimples adjacent to the heat stakes using a 5.5 mm (7/32 in) drill bit. 7. Install the heater air outlet cover. 8. Install the heater air outlet cover screws (2). Tighten Tighten the screws to 1.5 N.m (13 lb in) . 9. Connect the rear floor air outlet duct to the heater air outlet cover. 10. Install the rear floor air outlet duct to the holes in the floor reinforcement. 11. Install the floor carpet. 12. Install the RH Instrument Panel Closeout/Insulator panel. 13. Install the LH Instrument Panel Closeout/Insulator panel. 14. Connect the inlet and outlet heater hose to the heater core. 15. Use J 38185 in order to reposition the heater hose inlet and outlet clamps to the heater core. 16. Install the fuel injector sight shield. 17. Fill the cooling system.

Nov 13, 2009 | 2003 Chevrolet Monte Carlo

2 Answers

Need to remove heater core from 2000 Daewoo Nubira


  1. Disconnect the negative battery cable.
  2. Remove the instrument panel from the vehicle.
  3. Remove the heater/air distributor case from the vehicle.
  4. Disconnect the vacuum actuators from the vent/floor door and the defroster door.
  5. Remove the vacuum actuators from the heater/air distributor case.
  6. Remove the screws that secure the heater core cover to the heater/air distributor case assembly.
  7. Slowly separate the lower heater core cover from the rest of the assembly
  1. Remove the screw and the bracket clamp that secure the heater core lines to the case.
  2. Remove the spring clamp that secures the heater core body to the case.
  3. Remove the heater core from the case.
  1. Install the heater core into the case.
  2. Secure the heater core lines to the case with the retaining bracket clamp and the screw. Tighten the heater core retaining bracket screw .
  3. Install the heater core body with the retaining spring clamp.
  1. Install the heater core cover.
  2. Install and tighten the screws that secure the heater core cover to the heater/air distributor case assembly. Tighten the heater core cover screws
  3. Install the actuators for the vent/floor and the defroster doors.
  4. Install the heater/air distributor case.
  5. Install the instrument panel.
  6. Fill the cooling system
  7. Connect the negative battery cable.

Jun 18, 2009 | 2000 Daewoo Nubira

1 Answer

Blown heater core in a 1977 ford f-150 pick-up


1976-79 Without Air Conditioning
  1. Disconnect the temperature and function control Bowden cables from the heater housing. This must be done to prevent damage to the cables.
  2. Disconnect the wires from the blower resistor.
  3. Remove five screws attaching the air inlet (vent) duct to the heater housing.
  4. Disconnect the blower wires.
  5. Drain the radiator and remove the heater hoses from the heater core.
  6. Remove three heater stud retaining nuts and remove heater.
  7. Remove gasket between the heater hose ends and the dash panel at core tubes.
  8. Remove heater core cover and gasket (four screws).
  9. Pull heater core and lower support from heater.

To install:
  1. Install foam gaskets on heater core and install in heater assembly.
  2. Install the core seal and cover plate.
  3. Position heater assembly in vehicle and install three stud retaining nuts.
  4. Connect heater hoses to heater core and fill radiator.
  5. Connect blower motor wires.
  6. Place defroster nozzle on heater so that the defroster and heater openings are in the up position, and there is no air leak around the seal.
  7. Install air inlet (vent) duct to heater. Push duct firmly against seal on side cowl and tighten five attaching screws.
  8. Connect wires to blower motor resistor.
  9. Connect temperature and function control cables to heater, and adjust the cables.
  10. Reinstall gasket between the heater hose ends and the dash panel at core ends.
  11. Fill Cooling System.

  12. Hope this helps you! Please remember to rate my solution.

    Lefty64

Apr 09, 2009 | 1986 Ford F150 SuperCab

1 Answer

I do I change out a heater core on a 1997 GMC 1500 pick up truck


here is a step by step to replace your heater core. please do not forget to rate and comment about your experience with fixya today
Front
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the instrument panel glove compartment.
  4. Tag and unplug all electrical leads as necessary.
  5. Remove the center air distribution duct from the floor.
  6. If necessary, remove the ECM and mounting tray.
  7. Remove the hinge pillar trim panels.
  8. Remove the blower motor cover and then remove the motor.
  9. Remove the steering wheel and tilt back the instrument panel slightly.
  10. Remove the coolant overflow tank. Disengage the heater hoses at the core connections.
  11. Unfasten the attaching screws and nut and then remove the heater case.
  12. Remove the seven screws and lift off the heater case cover.
  13. Remove the fasteners and brackets that hold the heater core to the case and lift the core from the case.
To install:
  1. Install the heater core in the case.
  2. Install the heater case bottom plate. Make sure there is a good seal.
  3. Install the heater case into the truck. Tighten the 4 lower screws to 17 inch lbs. (2 Nm); the upper screw to 97 inch lbs. (11 Nm); and the nuts to 25 inch lbs. (2.8 Nm).
  4. Connect the heater hoses at the core tubes.
  5. Install the coolant overflow tank.
  6. Install the instrument panel and the steering wheel.
  7. Install the blower motor and cover.
  8. Install the trim panels and if removed, the ECM. Install the air distribution duct and reconnect all electrical leads.
  9. Install the glove compartment. Fill the cooling system and connect the battery cable.

Dec 22, 2008 | 1994 Chevrolet C1500

Not finding what you are looking for?
1993 Chevrolet K1500 Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...