Question about 1998 Toyota Camry

1 Answer

98 Camry brakes

I replaced front calipers; turned rotors and replaced disc; drove car w/o using brake petal; brakes gradually began to stick.

Posted by on

  • anastasia705 Nov 18, 2008

    I HAVE THE SAME PROBLEM. I CHANGED EVERYTHING BUT THE MASTER CYLINDER. NO ONE CAN FIGURE IT OUT.

  • Brian032472
    Brian032472 May 11, 2010

    I am a little confused. Did you replace the rotors or resurface them. I also noticed you didn't say as if you also replaced the brake pads. If I assume you did I would like to know if you replaced the caliper hoses and did you properly lube the slides and other caliper components.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 150 Answers

I would suggest replacing the caliper hoses and following a proper bleeding procedure before replacing the master cylinder

Posted on Nov 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2002 Ford Excursion 7.3 4x4 rear brakes getting smoking hot. Noticed it on driver side first. Assumed the rotor was sticking, replaced it and the hose. Relaxed pads and found the pads on passenger side...


There are a number of issues that can cause overheating disc brakes. Disc brakes, when released, separate from the disc by the action of the rotor moving between them (since no rotor is perfectly true, there is a small about of wobble and it pushes the pads away from the rotor surface). Things that can cause this to go wrong are:

  1. Caliper pistons that have rust rings that cause sticking. This most often will happen right after or shortly after replacing old, work out pads with new ones. Because the caliper piston was extended out farther with the worn pads, its surface may get rusty. This rust can cause sticking when the piston is pushed back into the bore with the new, thicker pads.
  2. Caliper slide bolts will rust and get sticky, not allowing the caliper to release properly and re-center itself on the rotor. What you often see here is that one pad (inner or outer) is totally worn out and the other seems normal.
  3. Rusty brake lines/caliper internals can cause restrictions in the flow of brake fluid and hold pressure after the brake pedal is released.
It is highly recommended that whenever you change your brake pads, you replace the caliper slide bolts use a new brake hardware kit when reinstalling. The additional cost is almost always saved in longer brake pad life, and fewer complications.

Mar 19, 2015 | 2002 Ford Excursion

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

How do you get the capierer pin off to put front brake pads on my Mercury Sable LS?


Section 06-03: Brakes, Front Disc 1999 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478) . Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120) , front disc brake rotor shield (2K004) or front wheel knuckle (3K185) .
  1. Remove rear brake pin retainers (2N386).
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125) . Do not pry directly against metal caliper piston or damage will occur.
  1. NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .

    Position disc brake caliper out of the way.
  1. Remove inner outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate .
  1. Inspect both rotor braking surfaces. Minor scoring or buildup of lining material does not require machining or replacement of front disc brake rotor.
-----------------------------------------------------------------
remove the 2 pins, #10 in pic. Usually has a dust cover over pin accessopening. Usually torx haed or hex head bolts (pins).


snorkelbobby_7.gif

Nov 12, 2010 | 1999 Mercury Sable

1 Answer

How to take back rotors off a 1994 honda civic.


PATH: Brakes > Front Disc Brakes > Brake Disc (Rotor) > Removal & Installation Removal & Installation
  1. Raise and support the front of the vehicle on jackstands. Remove the front wheels.
  2. Remove the caliper assembly; do not let the caliper assembly hang by the brake hose, instead support it with a piece of wire looped around the front spring or control arm.
  3. Remove the retaining screw from the brake rotor and remove the rotor from the hub.

An impact driver, No. 3 phillips screwdriver bit, and a hammer may be needed to remove the retaining screw. It is fairly easy to destroy the screw slots using an ordinary phillips screwdriver to remove the tightly driven screw (see photo).

  1. To install the disc, replace the disc on the hub, screw in the retaining screw and replace the caliper assembly.
edc2fe7.gif
PATH: Brakes > Rear Disc Brakes > Brake Disc (Rotor) > Removal & Installation Removal & Installation
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Disconnect the caliper from the caliper bracket. Support the caliper out of the way with a length of wire. Do not allow the caliper to hang from the brake hose.
  4. Remove the caliper bracket.
  5. Remove the two 6mm screws and the brake disc. If the brake disc is difficult to remove, install two 8mm bolts into the threaded holes and tighten them evenly to prevent cocking the rotor.
  6. Install the rotor in position. Install the two 6mm retaining screws.
  7. Install the brake caliper. Install the tire and wheel assembly.

PATH: Brakes > Rear Disc Brakes > Brake Disc (Rotor) > Removal & Installation Removal & Installation
  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Disconnect the caliper from the caliper bracket. Support the caliper out of the way with a length of wire. Do not allow the caliper to hang from the brake hose.
  4. Remove the caliper bracket.
  5. Remove the two 6mm screws and the brake disc. If the brake disc is difficult to remove, install two 8mm bolts into the threaded holes and tighten them evenly to prevent cocking the rotor.
  6. Install the rotor in position. Install the two 6mm retaining screws.
  7. Install the brake caliper. Install the tire and wheel assembly.

4d85ad3.gif

Sep 15, 2010 | 1994 Honda Civic

1 Answer

All new brake shoes on 97 jeep front callibers still sticking


The problem lays with the Caliper itself and/or the brake hose connected to the Caliper.
However if you replaced the pads, did you also replace the Rotors or have them Turned? The old pads wear the rotor. New pads on old rotors that have not been replaced or turned may end with rubbing or stuck brakes.
A simple way to test whether it's one and/or the other:
1. Remove the Caliper from the rotor, remove the pads. Keep for now the caliper attached to the brake hose.
2. Very slowly push on the brake, exposing more of the piston out of the bore. Not all the way. Usually until the rubber dust seal/boot is fully extended.
3. Check the seal/boot for cracks and tears, and if clean or not. Bad seals may prevent the piston from re-seating.
4. Using a c-clamp and pushing straight in: Try repushing the Caliper Piston back into the Caliper Bore (the cup back into the hole). It should go back in realitively easy.
5. If it doesn't go back in easy: Again slowly pump the brake and re-push the pistons back out to full extended seal/boot (but not the piston out of the bore).
6. Detached the brake hose from the caliper.
7. Again using a c-clamp and pushing straight in: Try again to repush the caliper piston back into the bore without the hose attached. If it goes back-in relatively easy - the caliper is okay...it is the brake hose.
8. If the caliper piston does not go back in easily - Replace the caliper.
9. When Installing the new (reman) caliper, remember to bleed the brakes.
TRY EITHER OR #10 OR #11 BELOW:
After the new Caliper is reattached to hose and has been bled:
10. Again push on the brake petal to fully extend the caliper piston fully (rubber seal/boot fully extended) Again do not push the piston out of the bore! Try pushing the piston back into the bore. If it does not re-seat relatively easy: Replace the brake hose.
11. Another method: After replacing the new caliper back on the rotor: Assumng the entire front end (2WD front wheel drive) or entire vehicle (2WD rear wheel drive) or (4WD all the time) is jacked up off the ground
a. Put the lug nuts back on the rotor.
b. Have helper Start the vehicle and place in Drive. Don't step on gas!
c. Have then let off the brake and then engage the brake.
d. When they let off the brake watch to see if the Rotor is turning or not, if rubbing or not. Or if still sticking.
e. With a new caliper, turned or new rotors, and still a problem? It is the brake hose!
12. Replace the brake hose and try again.

Another method but more expensive:
OR Replace the calipers, brake hoses; bleed and test!

If this helped or not; or if you need additional help or have addtional questions let me know on fixya.com!

Nov 28, 2009 | 1997 Jeep Grand Cherokee

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

2 Answers

98 TOYOTA CAMRY


I have had exacly the same issue, the mechanic replaced the brake pads, calipers, hoses/brake lines, then after all that and it still happening, he replaced the brake master cylinder and all was well, except for my wallet !!!!

Nov 19, 2008 | 1998 Toyota Camry

1 Answer

Brake problems!


I would recommend that you jack up the front end, and, with the hubs unlocked, turn the front wheels by hand. If either is stiff/hard to turn, you probably have the beginnings of a caliper issue, it may be sticking, rusted, or some issue like that. If one caliper IS stuck, I would def suggest replacing both at the same time, if one is bad, the other cannot be far behind.

Sep 30, 2008 | 1992 Toyota Pickup

1 Answer

Front Brakes


Interesting, disc brakes don't normally stick. Since there is no tension pressure against the pads like drum brakes.

You indicated you replaced the right caliper and the master cylinder, but no mention of the disc or the piston (Some caliper assemblies are all in one, some are not.)

Here are some thoughts:

Disc is contaminated with oil, grease, brake fluid etc, when you brake, it is absorbed by the pad, gets hot and sticks.

You didn't replace left caliper, piston isn't working well, sending all pressure to right side.

You didn't indicate, new, used or rebuilt caliper. If used, get anew/remanufactured SET of calipers and either semi-mettalic or ceramic pads, and new rotors (I used to get rotors turned, but new replacements are now generally cheaper that turning old ones. When working with brakes I always recommend you work them as a set, regardless of how good the other side looks.

Make sure you clean the rotors with a solvent to ensure any grease or anti-rust agent is removed and dry will with several paper towels.

When installing pads, ensure you do not touch the braking surface of the pad or the rotor, body oil can contaminate too.
Make sure that the siding surface of the caliper is lubricatred with silicone grease designed for calipers (little packets are available at your parts store) On my GM Cars, it is the bolts that mount the caliper, but this varies by caliper design

Hope that is

Jul 02, 2008 | 1995 Dodge Caravan

Not finding what you are looking for?
1998 Toyota Camry Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...