Question about 1997 Chevrolet S-10 Pickup

1 Answer

Starter need to replace starter but after getting it loose i can't get it out

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you got it unbolted all you need to do is disconnect the little support rod running from the bell housing to the front of the motor,pull that out of your way the best you can,then turn your starter vertically and wrestle it out between the lower pipe and cross member.its not going to be easy just dont give up!!!

Posted on Nov 04, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have a 97 Ford Ranger, manual transmission, had the slave clutch replaced, now have trouble with the starter, do you need to remove the starter to repair the clutch?

No the starter doesn't need to be removed,that part may be loose,may need pushing to click in place,Here's a link on the starter,that's what I read. Repair Guides Starting System Starter AutoZone com Here's a link on clutch slave cylinder removal,they may have just knocked it loose,try moving with hand to lock in. Repair Guides Starting System Starter AutoZone com

Feb 01, 2014 | Cars & Trucks

2 Answers

Has power but want turn over

Your starter is in need of replacement. I had a similar problem and replacing the starter corrected it.

Jan 20, 2013 | Cars & Trucks

1 Answer

Need to tighten loose starter how do I get to it?

Hi Anonymous, for more information about your question please visit the websites below. Good luck and have nice day.
2005 Harley Dyna FXDX starter replacement

Apr 26, 2012 | Cars & Trucks

1 Answer

My starter went out and when i replaced it it keeps hitting the fly wheel. a friend said he thinks the that ignition is not letting it disengage?

you need to shim the starter start with one shim if it still wont disengauge use next thicker one it should fix your starter. you can get shims at auto parts store. also when strarer is loose make sure you cant wiggle the flywheel it could be loose but unlikly (very rare)

Apr 28, 2011 | Ford E-250 Cars & Trucks

2 Answers

I recently replaced my battery in my 2000 jeep grand cherokee, but when I go to turn the key, it makes a clicking noise and won't start. What do I need to do.

sounds like a starter issue need to replace starter but before you replace startes check all wires from battery to make sure they are clean you can have the starter checked after you have it out at the parts store

Mar 03, 2010 | 2000 Jeep Grand Cherokee

3 Answers

Was driving fine ..parked the car went in the store came out and all i get is a clicking when i turn the key

check the battery and connection if they are good then replace the starter it is bad, you can try having someone tap on the starter while cranking it over it may start but the starter is still bad, hope this helps.

Feb 19, 2010 | 1992 Ford Taurus

5 Answers

Clicking not turning over battery good

Bad battery connection or loose wire.Clicking noise is a relay not getting enough or intermitant power from the battery

Aug 07, 2009 | 1995 Isuzu Rodeo

2 Answers

Dead battery. Just getting a little click when I boost it but I have enough juice for the interior lights. Does it sound like the starter or a loose connection?

Check battery connections first for looseness, corrosion, etc;... If the starter clicks it is a power issue not the starter. The battery may need to be fully charged or replaced take it to a local patrs store and have them check it.

Jun 28, 2009 | 2002 Pontiac Montana

1 Answer


at the right side of the vehicle under the battery there is the starter bolted by three screws you need to get under the vehicle to loose the screws use a 14mm socket and wrench to get the bolt loose it takes a bit of maneuvering to get it out of the tight space but it is possible and simply reverse to get the new one in remember to disconnect the battery and the lines to the starter before starting to work.

Nov 27, 2008 | 1999 Kia Sportage

1 Answer

Starter replacment

If you are a larger person, you will need to get the front end into the air so you can move under it. Make certain to block the wheels! I had to take off a bar that ran under my starter before I could completely remove the starter. When I took the starter off, a plate fell to the ground. I didn't know what it went to, so I didn't put it back in. I wound up having to take the starter loose again to replace the plate, turned out it was a shim and was needed to help the starter last as long as possible. Also, the first rebuilt starter I bought was faulty. All in all I had to take the starter loose three times before I was done. Works fantastic now!

Oct 07, 2008 | 1987 Chevrolet S-10 Pickup

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides