Question about 1988 Dodge Ram 50

1 Answer

Replaced gasket on front of 1988 dodge 50

Now it cranks but has a vibration

Posted by on

1 Answer

I have the same truck give your truck a tune up.

Posted on Nov 02, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is oil leaking from just above oil pan and around timing belt cover?


Rear engine seal is probably where it is coming from. The other thing to check is the seals you replaced. If they were over or under tightened they can still leak from there.

Aug 30, 2014 | 1988 Dodge Ram 50

1 Answer

On the 2007 dodge caravan has there been many problems with it leaking oil from the crank?


This could be a result of the gasket leaking that is between the engine block and the crank case cover (front of engine), or it could be the front crankshaft gasket itself. If it is leaking from the rear of the engine it could be an issue with the gasket between the transmission and the engine block.

Either way it sounds like an issue with a gasket. A replacement could range from ~$200 for a crank case cover to ~$500 for the crankshaft seal.

Sep 08, 2011 | Dodge Caravan Cars & Trucks

1 Answer

Need too know the timming marks on where to set them at on a 1988 dodge ram 50 2.0 4 cyl


Here are the timing marks for the timing belt and also the balance shaft, when replacing the timing belt you should also replace the balanceshaft belt heres a diagram for both of them good luck and hope this helps.35de2d2.gif9665995.gif

Aug 13, 2010 | 1988 Dodge Ram 50

2 Answers

Find crank position sensor


The crankshaft position sensor should be located behind the vibration damper/harmonic balancer and it will have to be removed before the crankshaft position sensor can be replaced. (Let me know if you require assistance with the proceedure)

Also, it usually requires a special tool to align that sensor (available from most auto part stores) and if the sensor is not properly aligned then damage to the sensor or the tone ring can occur.

Here is an image of the crankshaft position sensor with the vibration damper/harmonic balancer removed.



cc35f9e.jpg

Jul 11, 2010 | 1988 Buick LeSabre

1 Answer

Where is fuel pump on dodge ram 50 1988


If its the same as my 1989 dodge ram 50 it sits on the engine block by the carburator

May 19, 2010 | 1988 Dodge Ram 50

1 Answer

Have grand caravan 2001 awd i get to 50 it starts vibrates think it might be carrier bearing after 50 it seems to lessen some no problem in front end what do u think


Most vibrations at speeds from 45mph to 55mph indicate tire balance problems. If there is no vibration outside this range have the tire balance checked. If there is a vibration that starts around 50mph and continues at higher speeds there could be a problem with the CV joint(s).

Nov 05, 2009 | 2001 Dodge Caravan

1 Answer

I have a 1990 dodge ram and it use to vibrate when it gets around 50-55 now it vibrates at lower speed help please


Have the wheels computor balanced, and check the front end, might have a worn ball joint, tie rod end, etc.

Aug 25, 2009 | 1990 Dodge Ram

1 Answer

Ford 1988 escort GL-Front wheel constant scrape-scrape,vibration


sounds like you need new brake pads and the rotors atleast turned down if not replaced
the pads should stop the noise and the rotors should stop the vibration/wobble
thanks wes
ps please rate me

Mar 27, 2009 | 1988 Ford Escort EXP

2 Answers

Where is the Fuel Filter located on 1988 Dodge Ram 50


Under hood, center, lower engine area, between fuel pump and carburetor, mounted in fuel line

Nov 08, 2008 | 1988 Dodge Ram 50

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...