Question about 1991 Oldsmobile Bravada

Open Question

1991 olds bravada v-6 vortec

A new distributor was installed now my idle is way too high and on the drivers side my exhaust manifold and pipe turns red hot

Posted by on

6 Suggested Answers

SOURCE: 2003 escape idling to high, exhaust pipes turning orange red, not cataylic

Your escape is a 3.0L duratec motor. Is the motor itself overheating or just the pipes? The high idle is often related to a dirty Idle Air Control module or IAC, which is located on the top of the motor near the throttle body. If you clean this, or replace it, after a few days the high idle is often times solved.

Posted on Sep 30, 2008

tripletauto
  • 1450 Answers

SOURCE: coolant in exhaust pipe but not the oil

THIS SOUNDS LIKE YOU ARE TALKING ABOUT EGR PIPE. AND NO IT WONT CAUSE COOLANT

Posted on Dec 30, 2008

  • 57 Answers

SOURCE: 1991 Olds Bravada 4.3 v6 rough idle and backfiring.

Ok guys, let's fix these things here!
Just went through this myself, so do the following:
Go to your local parts store and buy a Haynes Repair Manual.
You need to read the book first, learn how the ECM (Electronic Control Module) works. You'll see that there are alot of sensors and components that make up the fuel emissions bologna.
The nice thing about this system is not only does the ECM control all electrical functions, it also trouble-shoots it's self. When a component or sensor goes out, the ECM stores a code for that event in it's memory. You can use the Haynes Repair Manual to put the ECM into diagnostic mode and thus read any codes present.
So, all that's left is replacing what the EMC tells you too! :) Good Luck!

Posted on Feb 06, 2009

  • 63 Answers

SOURCE: o2 sensor location

It should be screwed into the exhaust manifold - it will kook like a spark plug with one wire on it.

Posted on May 24, 2009

csmock132
  • 4669 Answers

SOURCE: 1994 Oldsmobile Bravada stalls at idle. I replaced

Doubt it's the exhaust. Does it run rough or just idle so low it quits

Posted on Aug 16, 2009

  • 114 Answers

SOURCE: i have an audi 80 misfiring on idle but ok when

Check the rubber intake boot and all vacuum hoses.

Posted on Sep 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of camshaft position sensor on a 2002 oldsmobile bravada


4200 vortec, Its located in front of engine, its just below the engine oil fill cap, right by the coolant hose is the camshaft position sensor (CMP)
If your looking for the camshaft positioning actuator solenoid its location is on the exhaust manifold side on the top right corner of the cylinder head, if your looking at the motor from the exhaust side, its behind the power steering fill. You have to remove the belt to loosin the power steering pump through the pulley then kind of push it aside as you take out the camshaft actuator solenoid.

Feb 29, 2016 | 2002 Oldsmobile Bravada

2 Answers

How many Oxygen sensors on a `99 Olds Bravada?


you should have three.

There will be one on each exhaust pipe near the exhaust manifolds and one after the catalytic converter.

May 03, 2011 | 1999 Oldsmobile Bravada

1 Answer

How to replace the exhaust manifold ring in my 91 Toyota Tercel


There is a bracket that attaches the exhaust pipe to the engine block. Remove the 2 screws that hold
that bracket on. I think they are 12mm heads. Detach the 2 exhaust manifold to exhaust pipe screws,
the screws have 15mm heads. A 15mm deep socket is best. After you remove those 2 15mm screws you can pull the exhaust pipe down, remove the old exhaust flange and put the new one on.

Rettach the exhaust manifold to pipe screws, and reattach the bracket and youre done.

Mar 07, 2011 | 1991 Toyota Tercel

2 Answers

Cylinderhead torque stc.


Cylinder Head Removal & Installation SOHC To Remove:
  1. Relieve fuel system pressure.
  2. Remove timing belt cover. Camshaft timing marks kia-03-20-7032.gif

  3. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  4. Loosen lock bolt on tensioner.
  5. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt.
  6. Remove timing belt from camshaft pulley.
  7. Disconnect battery negative cable.
  8. Remove 3 bolts that secure accelerator cable and air intake hose to cylinder head cover.
  9. Detach accelerator cable and place off to side.
  10. Remove the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  11. Disconnect mass air flow sensor electrical connector.
  12. Remove air intake hose.
  13. Remove PCV valve from cylinder head cover.
  14. Remove ISC air hose from idle speed actuator.
  15. Remove air hose from behind intake manifold.
  16. Remove 2 screws from high tension wire protectors.
  17. Detach wire loom from holder at rear of cylinder head cover.
  18. Detach vacuum tube at rear of cylinder head cover.
  19. Remove vacuum pipe. Cylinder Head Cover kia-03-20-7042.gif

  20. Remove 7 cylinder head cover bolts.
  21. Remove cylinder head cover and gasket.
  22. Disconnect 2 ignition coil electrical connectors.
  23. Disconnect 2 fuel injection electrical connectors at rear of cylinder head.
  24. Disconnect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  25. Disconnect heater hose from elbow.
  26. Disconnect brake booster vacuum hose and cruise control vacuum hose from surge tank.
  27. Detach wire harness from rear of cylinder head.
  28. Disconnect purge control solenoid vacuum hose from intake manifold.
  29. Disconnect fuel hose from fuel connector assembly.
  30. Remove grounding bracket.
  31. Remove 4 bolts and intake manifold bracket.
  32. Remove starter.
  33. Detach water bypass hose from bypass pipe.
  34. Disconnect water hoses from oil cooler.
  35. Disconnect fuel hose from fuel pipe.
  36. Remove exhaust manifold heat shield.
  37. Remove exhaust flange nuts and front exhaust bracket bolt.
  38. Lower exhaust system. Cylinder head bolt loosening sequence kia-03-20-7050.gif

  39. Loosen cylinder head bolts in 3 steps in proper sequence.
  40. Remove cylinder head bolts and washers.
  41. Remove cylinder head, intake manifold and exhaust manifold as an assembly.
To Install:
  1. Install NEW cylinder head gasket.
  2. Install cylinder head, intake manifold and exhaust manifold as an assembly.
  3. Tighten cylinder head bolts in 3 steps in reverse sequence that was used during removal. Tighten bolts to 62 ft lb (84 Nm).
  4. Install front exhaust bracket bolt. Tighten bolt to 20 ft lb (27 Nm).
  5. Install NEW lower exhaust flange gasket and 3 nuts. Tighten nuts to 24 ft lb (31 Nm).
  6. Install exhaust manifold heat shield. Tighten nuts to 35 in lb (4 Nm).
  7. Connect fuel hose to pipe.
  8. Connect 2 hoses to oil cooler.
  9. Attach water bypass hose to bypass pipe.
  10. Install starter and bolts. Tighten bolts to 34 ft lb (46 Nm).
  11. Install intake manifolds bracket and 4 bolts. Tighten bolts to 32 ft lb (45 Nm).
  12. Install grounding bracket.
  13. Connect fuel hose to fuel connector assembly.
  14. Connect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  15. Connect purge control solenoid vacuum hose to intake manifold.
  16. Attach wire harness from rear of cylinder head.
  17. Connect brake booster vacuum hose and cruise control vacuum hose to surge tank.
  18. Connect heater hose to elbow.
  19. Connect 2 fuel injection electrical connectors at rear of cylinder head.
  20. Connect 2 ignition coil electrical connectors.
  21. Install cylinder head cover.
  22. Install 7 cylinder head cover bolts. Tighten bolts to 60 in lb (7 Nm).
  23. Install vacuum pipe and 2 bolts at rear of cylinder head cover. Tighten bolts to 60 in lb (7 Nm).
  24. Connect vacuum tube to pipe.
  25. Connect loom holder to rear of cylinder head cover.
  26. Install 2 screws to high tension wire protectors.
  27. Install air hose to behind intake manifold.
  28. Install ISC air hose to idle speed actuator.
  29. Install PCV valve to cylinder head cover.
  30. Install air intake hose.
  31. Connect mass air flow sensor electrical connector.
  32. Install the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  33. Attach accelerator cable.
  34. Install 3 bolts that secure accelerator cable and air intake hose to cylinder head cover. Timing belt pulley timing marks kia-03-20-7035.gif

    NOTE: Timing belt pulley timing mark and timing mark must be aligned.
    Camshaft timing marks kia-03-20-7032.gif

    NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
  35. Install timing belt.
  36. Install timing belt cover.
  37. Pressurize fuel system.
  38. Start engine and check ignition timing.

Jul 11, 2010 | 1999 Kia Sportage

2 Answers

Where is the oxygen sensor located in a 1991 honda accord


1991 Honda Accord 2.2L FI 4cyl
The Oxygen Sensor is located under hood, driver side, rear engine area, below exhaust manifold flange, mounted in exhaust pipe.
Application: EX model

Good luck.

Mar 16, 2010 | 1991 Honda Accord

2 Answers

How to change an exhaust manifold leak 7.5L


Right-Hand
Removal
  1. Remove spark plug heat shield (12A406).
  1. Remove distributor to spark plug wires (12286) using Spark Plug Wire Remover T74P-6666-A.
    1. Disconnect muffler inlet pipe.
    1. If equipped with secondary air injection, disconnect the secondary air injection check valve tube (9B480).
    1. Remove attaching bolts and right exhaust manifold (9430).
    1. Inspect joint faces for signs fo exhaust leaks, cracks or any defect that would make exhaust manifold unfit for use







Left-Hand Removal






1. Remove oil level indicator tube (6754).
  1. Remove spark plug heat shield.
  1. Remove distributor to spark plug wires using Spark Plug Wire Remover T74P-6666-A.
  1. Disconnect EGR valve to exhaust manifold tube (9D477). If equipped with air injection, disconnect the secondary air injection check valve tube.
  1. Disconnect muffler inlet pipe.
  1. Remove attaching bolts and exhaust manifold (9431).
  1. Inspect joint faces for signs of exhaust leaks, cracks or any defect that would make the exhaust manifold unfit for use.
Installation
  1. Clean mating surfaces of right exhaust manifold or left exhaust manifold and cylinder head (6049). Clean mounting flange of right exhaust manifold or left exhaust manifold and inlet pipe(s). Clean mounting surface for air injection tube or right exhaust manifold. Apply light film of Premium Long-Life Grease XG-1-C or -K or equivalent meeting Ford specification ESA-M1C75-B to right exhaust manifold or left exhaust manifold.
  1. Position right exhaust manifold or left exhaust manifold on cylinder head. Install attaching bolts and washers, starting at fourth bolt hole from front of each right exhaust manifold or left exhaust manifold. Tighten bolts to 34-47 Nm (25-35 lb-ft), working from center right to both ends.
    1. Position inlet pipes to right exhaust manifold or left exhaust manifold. Install attaching nuts and tighten to 34-47 Nm (25-35 lb-ft).
    1. Position the secondary air injection check valve tube and the secondary air injection tube gasket (9C435) at rear of right-hand exhaust manifold. Install attaching bolts and tighten to 19-25 Nm (14-18 lb-ft).
    1. Attach the secondary air injection manifold tube (9B449) to left-hand exhaust manifold fitting (located under EGR tube). Tighten nut to 30-40 Nm (22-30 lb-ft).
    1. Attach the secondary air injection check valve tube to rear of right-hand cylinder head. Tighten bolts to 75-85 Nm (56-62 lb-ft).
      1. Connect EGR valve to exhaust manifold tube to left exhaust manifold, if removed. Tighten nut to 53-72 Nm (39-53 lb-ft).
      1. Install spark plug heat shield and distributor to spark plug wires.
      1. Install oil level indicator tube to left exhaust manifold, if removed. Tighten nut to 13-24 Nm (10-18 lb-ft).
      2. Start engine (6007) and check for exhaust leaks.







b913da4.gif
28b39c6.gif
Hope this helps you...WF †

Mar 10, 2010 | 1996 Ford F250 Crew Cab

1 Answer

Hot do you take off a 98 GMC 5.7 vortec intake


Note, removing the upper intake manifold is not necessary when removing lower intake manifold, they are removed as an assembly.
Disconnect negative battery cable. Drain cooling system. Remove air cleaner assembly and inlet duct. Mark and remove distributor. Remove upper radiator hose at thermostat housing. Disconnect accelerator and cruise control cables. Remove heater hoses from intake manifold. Remove EGR pipe.
Disconnect fuel lines at rear of engine. Remove AC compressor and set aside(leave hoses connected). Remove canister purge solenoid. Disconnect theSCPI injector, ignition coil, Ignition Control Module, generator,IAC motor, TP sensor, O2 sensor, Exhaust Gas Recirculation valve and Engine Coolant Temperature sensor wiring harness connectors. Remove PCV valve and hose. Remove lower intake manifold bolts. Remove lower intake manifold.
Installation.
Always use New O-rings when reconnecting fuel lines at rear of engine. Apply a bead of RTV silicone sealer along the front and rear sealing surfaces of the block.See Fig.6. Install new gaskets and intake manifold on block while RTV is still wet to the touch. Use Threadlock 12345382 or equivalent to lower intake manifold bolts. Tighten lower intake manifold bolts in sequence to specification table. See fig. 7. To complete installation, reverse removal procedure.f52665d.gifabc2b5f.gif

Oct 10, 2009 | 1998 GMC Sierra

1 Answer

O2 sensor location


It should be screwed into the exhaust manifold - it will kook like a spark plug with one wire on it.

May 24, 2009 | 1998 Oldsmobile Bravada

1 Answer

Coolant in exhaust pipe but not the oil


THIS SOUNDS LIKE YOU ARE TALKING ABOUT EGR PIPE. AND NO IT WONT CAUSE COOLANT

Dec 30, 2008 | 1990 Chevrolet Suburban

Not finding what you are looking for?
1991 Oldsmobile Bravada Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...