Question about 1999 Dodge Durango

1 Answer

Rear tail light

I am having a problem with the left rear light. The break light works when applied but the tail light does not work. and the bulb is new. Also, I need to know what the color code is for the light as I am installing a wire harness for a trailer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 512 Answers

White with tan tracer....brake lights
light green...left turn
tan ....right turn
black with yellow tracer....tail lamp
violet with black tracer....backup lamps

as far as the bulb not lighting it could be either the socket or the circuit board

Posted on Nov 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

I have a 1993 chevy pick up. The break lights work but the tail lights do not.when i apply the breaks the break lights and the tag lights come on when i turn on the parking lights on the break lights no...


Could be a number of problems. First, check and make sure the bulbs are not blown, that is if the brake lights and tail lights are the same bulbs. If it's not that, check the fuses for the tail lights/driving lights. From there, it could be a problem with the switch or wiring.

Sep 08, 2013 | Cars & Trucks

1 Answer

Rear tail lights/wiring


check the light bulbs (filiments can break and touch the other filament in the bulb and backfeed other circuits) if they appear ok remove the non working bulbs and swap positions with the working bulbs and see if anything changes

Apr 04, 2013 | Cars & Trucks

1 Answer

Left tail light not working


replace the bulb it is a double filament bulb and most likely is partially blown

Jun 11, 2012 | 1994 Volkswagen Jetta

1 Answer

Only left tail light does not work. left break light works fine. All other lights work. New bulb, good fuse, and new connector that the bulb plugs into. I can ground the middle wire going into the...


poor ground, check the wire harness, this is the one that comes from front of vehicle to the rear and plugs into the wires that go to the rear lights. trace the wire coming out of the light itself and eventually you will see that it comes to a connector that attaches to the wiring harness.

Sep 03, 2010 | Ford Windstar Cars & Trucks

1 Answer

Jaguar xj6 break light cancels signal


Replace the turn signal switch. Bad contact inside causing a crossing of the circuits. When the turn signal is applied it should open the brake light circuit allowing for just the signal to work. Doesn't sound like the switch is doing it's job.

May 23, 2010 | 1989 Jaguar Vanden Plas

1 Answer

96 contour. left tail light, 1 and 2nd break light are out.


Everything works, more or less, so you know that the switches and fuses are good. That means that you've got either bulb problems or power/ground problems. First, try swapping the bulbs around to see if the "bad" lights will work with the known "good" bulbs in them. If so, you just need to replace some bulbs. If not, check the sockets inside and out for corrosion, clean them (wire brush, steel wool, sandpaper, etc.) if necessary, and use a voltmeter or automotive tester to make sure that you have power and ground to each socket. The fast flash on the turn signal is just an indicator that a bulb is out.

Bill B

Apr 28, 2010 | 1996 Ford Contour

1 Answer

Tail break lights don't work. Window break light does work however. Bulbs have been replaced.


Check the brake light fuse. The high mounted brake light (third brake light) is on a different circuit than the brake lights. Hope this helps.

May 23, 2009 | 1998 Mercury Mystique

1 Answer

Rear lights


Try removing the the bulbs from the left tail light and cleaning sockets and bulb bases (or replace them).
It sounds like a contact problem which may be exacerbated by having the tail light on when the brake light attempts to light.
There are probably also quick disconnects plugged onto the light fixtures that might be corroded but those are not as easy to clean.

Aug 20, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
1999 Dodge Durango Logo

576 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...