Question about 1991 Ford Taurus

1 Answer

1991 ford taurus turn signal

My turn signal does not return to the off position after turning. What set it back to the off?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 426 Answers

You will have to change the turn signal wand as there is a small plastic lever that wears out it is activated by a plastic sleeve that fits around the steering rod and locks into the steering wheel.I

Posted on Nov 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

All signals and other flashers work but passenger front flashers do not work


Use a test light, test for power and ground at the bulb contacts. Then test for power and ground at the wires. Probably needs a new socket, common problem.

Oct 27, 2015 | 1995 Ford Taurus

1 Answer

Directional keeps blinking


I would have to conclude that the turn signal switch is faulty or some wires may be melted together near the area that keep the directional side powered up.I am sure your turn signal lever is going back to the stop position?

May 27, 2014 | 1994 Ford Taurus

1 Answer

Crank sensor


Print


Location

Specific to:
Ford Taurus 2008-2009
Mercury Sable 2008-2009


0996b43f80e43304.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Crankshaft Position (CKP) sensor (7)


Operation

Specific to:
Ford Taurus 2008-2009
Mercury Sable 2008-2009
The Crankshaft Position (CKP) Sensor is a permanent magnet output coil device that monitors the speed and position of the crankshaft. A reluctor is attached directly to the crankshaft, and is used to generate a constant signal as it passes the CKP sensor magnetic coil. The CKP Sensor utilizes system voltage (12 volts DC), or reference voltage (5 volts DC) to generate a digital output signal to the PCM that is based upon a 0.5 volt AC reference. The alternating magnetic field is used by the sensor output electronics to produce a digital pulse. The CKP sensor returns a digital ON/OFF signal pulse during each revolution of the crankshaft, with a momentary signal interrupt for the top dead center (TDC) position of the #1 cylinder. The Pulse Width Modulation pattern is used by the Powertrain Control Module (PCM) to calculate ignition timing, fuel injector timing, misfire diagnostics, and the tachometer display

Jun 20, 2012 | 2008 Ford Taurus X

1 Answer

2001 ford taurus turn signal switch replacement does'nt make blinker work


I suggest you take the car back to the person that as done the work.

Mar 25, 2012 | 2001 Ford Taurus

1 Answer

Location of turn signal flasher


The Turn Signal Flasher is located behind the left end of the instrument panel, above the fuse box.

Feb 08, 2011 | 1991 Ford Taurus

1 Answer

Driver's electric seat moves backwards, but nothing happens when trying to return it to desired position more forward


Sometime the gear position run out of tract. Check it again and give a knock on ity. It might work.

Aug 06, 2010 | 1991 Ford Taurus

2 Answers

96 Ford Taurus no turn signals or hazards


Take the turn signal lever and jiggle it, a lot. If they start working, the switch is bad. You can also turn on the hazards and take hold of the button and push it left , right , forward and back and see if they start working. If so, replace the turn signal/ hazard switch.

Nov 24, 2009 | 1996 Ford Taurus

1 Answer

Back blinkers not working, front good, FUSE GOOD, LIGHT GOOD


set ur hazards if they blink its not ur wirring its either ur turn relay or turn switch

May 22, 2009 | 1994 Ford Taurus

1 Answer

1988 Ford Taurus Turn Signals do not work


Yes, it certainly could be the switches in the windshield wiper stalk off of the steering column.
From day one, my (used 14K) 93 Taurus turn signals worked in some positions of the wiper speed and not in other positions of the wiper speed. Fortunately, they always work when the windshield wipers are off.

Oct 22, 2008 | 1988 Ford Taurus

1 Answer

Turn signal switch


'm not sure but I'll put in my 2 cents worth.

I changed a turn signal switch on an older model and it wasn't too difficult. First you have to remove the horn button or top center piece of the steering wheel. There should be screws from the bottom side that you remove to do this. Once you get that off there is simply a large nut in the center than needs to be removed that holds the steering wheel on. [I did not need any sort of steering wheel puller.] Once the steering wheel is off you'll see how the turn signal switch is attached. its simply a matter of disconnecting the wires and removing screws and then putting everything back together. Make sure you get the steering wheel properly positioned. Before you start simply make sure the wheel is positioned in the straight ahead position.

Jun 23, 2008 | 1996 Ford Taurus

Not finding what you are looking for?
1991 Ford Taurus Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...