Question about 2002 Ford Windstar Cargo

2 Answers

Fordwindstar how to replace starter

Posted by on


2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 66 Answers

Disconnect battery. Raise vehicle so you can get under it. Make sure you block wheels and apply parking brake if your using ramps. You'll need 3/8" drive 13mm & 15mm sockets (deep) rachet and an extention. 10mm 1/4" drive socket and rachet. Remove the two starter wires from the starter. Remove the ground cable nut. Move the cables out of your way and remove the bolts holding the srter to bell housing. Starter will come out now. Reverse the procedure to install the new one. 

Posted on Jan 04, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Markgas sistem

Posted on Nov 28, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2003 fordwindstar skipping after rain

What do you have coils or cap?

Jul 20, 2016 | Cars & Trucks

1 Answer

Location of computer module fordwindstar 2002

It is located to the left of the cabin air filter. in the wiper cowl. Look above the power steering reservoir and AC dryer canister. A multi - pin harness will protrude from it.

Jun 11, 2014 | 2001 Ford Windstar

1 Answer

1996 fordwindstar replacing the stater

What info do you need? It is on the front of the engine along side the oil pan near the radiator.

Aug 11, 2010 | 1996 Ford Windstar

1 Answer

I have a 98 Fordwindstar 3.8 . It failed emission on code P0340 . I replaced the cam shaft position sensor it still shows code P0340 what else could it be?

the input to the sensor must also be checked. this link provides some diagnostic procedures. diagnosis for camshaft and crankshaft sensors are similar, as stated in the article.

Jun 10, 2010 | 1998 Ford Windstar

1 Answer

How do u fix a rack and pioion

whats wrong with it? there is no 'fixing" you will need to replace it. check the tie rods and it wil lneed a front end alignment.

Jun 05, 2010 | 1998 Ford Windstar

1 Answer


2001 FORD WINDSTAR - V6 3.8L 232ci GAS FI N 4

Belt Routing Diagram Multiple Accessory, w/A.C.


From DAYCO Catalogue.

Hope this help (remember rated this).

Mar 28, 2010 | 2001 Ford Windstar

2 Answers

Looking for my computer to get some numbers off of it its a 99 fordwindstar, 3.8

ECM is located behind the glovebox or behind console
The PCM is located behind the passenger's side of the firewall.

Mar 16, 2010 | 2001 Ford Windstar

1 Answer

I have 1998 fordwindstar and it is blowing cold air instead of heat.

this problm is caused by a defective air temperature control blend door or a blend door actuator motor, both are replaced during a repair, the motor and the door it operates is buried deep in the dash, the entire dash assmebly must be removed to replace the defective parts (a 10-12 job), a factory service manual is a must, on a scale of 1-10 with 10 being the most difficult this is a 9

Dec 10, 2009 | 1998 Ford Windstar

1 Answer

I'm working on a 2003 fordwindstar,Replaced the Compresser & pump ,New orificetube,New accumulator.When loading thesystem (3.8Lbs With rear air) the clutch wont stay on.. it constantly kicks off after...

what is the high side?,,,ow side about right ,high side should be no more than 225-250 at the max ,if it is higher than this make sure the fan or fans are working if so ,replace the condenser.if high side is normal replace low side cut out switch

Jun 29, 2009 | 2003 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

1,238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5613 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides