Question about 2000 Toyota Camry

1 Answer

Need to change interior lights

I need to replace the bukb for the interior light but cannot remove the cover. How do I remove without breaking it.

Posted by on

  • Anonymous Dec 29, 2008

    My interior light is not working as well I so replaced the bulb and its still not working

  • atascadero Mar 22, 2009

    Now to find the small slot!



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

Very easy to remove: You insert a small flat blade screwdriver into the small slot, an pry it open. The plastic is rather strong; if you pry on the center of the slot, it will not break. Hope this helps.

Posted on Nov 03, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1992 brougham cadillac dashboard lights is gone out how do you change them

Trim has to first be removed as you sit in your seat and look at it. Study it, and you'll figure it out. Sometimes when you're pulling on it, it'll feel as though it'll break but it usually doesn't. This is too intense a subject to cover without some tutoring. With or without a tutor, you may be talking like a truck drivin' Sailor before you get to the lamps that need replacing. So start by taking not of the location of the dash lamps that're not lighting up.

Mar 16, 2014 | 1989 GMC Suburban

1 Answer

How do I change the light in the maplight of 2011 odyssey

Use a Small flathead screwdriver and pry open the clear plastic cover over the bulb. Then replace bukb

Oct 16, 2013 | Honda Odyssey Cars & Trucks

1 Answer

Interior bulb replacement Smart Car

You should remove the covers , front panel so that you would have access to the light , then you can replace

Apr 14, 2013 | Smart Cars & Trucks

2 Answers

How do I change the interior light in a 2002 chrysler sebring

perhaps if you were to take a good picture and post it we would have a better idea, as I can not imagine a metal cover over the bulb unless it is some sort of heat shield .

Aug 21, 2012 | 2002 Chrysler Sebring

2 Answers

Replace license plate lights

Hi there,

Firstly, remove the four screws on the bottom of the license plate light assembly using a Phillips screwdriver. Then pull the license plate light cover out away from the rear of the car. Pull the bulb forward and pull it straight out of the wiring socket.

A press the new bulb into place until it is secure. Push the bulb and wiring assembly back up inside the light assembly and replace the license plate light cover. Replace the four screws that secure the light cover and tighten them with a Phillips screwdriver. Finally, turn on the lights to test the new bulb.

Hope this helps...

Jan 17, 2011 | 2007 Toyota Sienna

1 Answer

Need to change out back brake light on 2006 nissan

take interior cover behind tail light inside trunk off.the bulb the bulb twist locks in hole(twist counter clockwise to remove)repeat procedure to replace.

Mar 23, 2010 | 2006 Nissan Altima

1 Answer

The interior dome light is burned out, removing cover problem.

You will have to pry off the lens CAREFULLY using a small screwdriver. There are two little plastic protrusions on each long side of the lens which fit into the casement. You can ease the casement away from the lens enough to get it to pop out. Re-inserting it is the same, but probably easier.
Gently, give it a try.
Hope this helps you.

Oct 23, 2009 | 1994 Honda Accord

1 Answer

I need to replace the Passenger rear view mirror on a 2002 Chevy

Use a long flat head screw driver with electrical tape wrapped around it(to prevent scratches). Have some one help you and hold a light so you can see the snaps on the inside, be really nice about it and pry the panel from the door frame.

Aug 21, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

2000 LaSarbe interior lights do not work

take the cover off the fuse box .. it may display the location of individual fuses on the cover inside as most do.

Jul 31, 2009 | 2000 Buick Regal

Not finding what you are looking for?
2000 Toyota Camry Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8825 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides