Question about 1999 Jeep Wrangler

1 Answer

Installing after market fog lights

I am installing a set of PIAA fog lamps on my 99 Wrangler.  The car is pre-wired for Fog Lamps.  I have ordered the Switch (Standard DS1082) that fits in the unused spot next to the Rear Wiper and Defroster switches for the Hard Top.  There is already a plug set up in the jeep that will fit the Fog Lamp switch.  Now I need to find out where are the wires that I can hook up the fog lamps.  I am assuming that they are already run into the engine compartment on the engine side of the firewall.  Does this make sense? Where can I find the wires?  U can email me at fsmith@harpers.org.  THANX 4 THE HELP!!!

Posted by on

  • Anonymous Mar 12, 2014

    unable to activate fog lamps

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 393 Answers

Look where they mount the lights connectors are probably right there

Posted on Nov 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How turn on my fog lights on 99 montana or its turn on by itself


Fog Lamps The fog lamps switch is located in the instrument panel switchbank. Push the fog lamp symbol on the switch to turn on the lamps. The indicator light will glow. Push the ribbed part of the switch to turn them off. The indicator light will go off. Your parking lamps or headlamps must be on for your fog lamps to go on.
http://www.pontiac.com/content/dam/pontiac/northamerica/usa/nscwebsite/en/Home/Owners/Owner_Resources/Manuals/en/us/1999/montana/1999-pontiac-montana-owners-manual.pdf.pdf

Page 2-63 of owners manual

Dec 26, 2015 | Cars & Trucks

3 Answers

How do I turn on fog lights on a Cadillac escalade esv 09


If it is a turn knob for lights just pull out on knob

Apr 27, 2015 | 2009 Cadillac Escalade ESV

1 Answer

HOW DO YOU INSTALL THE DAYTIME DRIVING LIGHTS OR THE FOG LAMPS ON THE FORD FUSION 2007


New car day running light is achive only by ecm programming

Ask the dealer

Apr 12, 2014 | Ford Cars & Trucks

1 Answer

I have a 2001 jeep grand Cherokee Laredo that did not come with fog lights but has the plugs for the bulbs. I purchased the fog lights plugged them in but they didn't turn on. I was wondering if there...


If this vehicle came prewired, and all you had to do was plug in the fog lamps, then 50A fuse 7 in the power distribution center would be hot at all times, applying power to 15A fuse 24 and the fog lamp relay. Setting the left multifunction switch to FOG causes the body control module to close the fog lamp relay and turn on the fog lamps. It is possible your Jeep came prewired but without the fuses and relay so a dealer could install them to make your fog lamps work. You can check whether the fuses are in the box and OK and whether the fog lamp is installed or just an empty socket. Once everything has been checked and any missing parts installed, your fog lights should work.

Sep 18, 2012 | Cars & Trucks

1 Answer

Looking for fuse for fog lights on a 2008 dodge charger. we installed a fog light kit. the car is pre-wired for them. we replaced the head light switch with the one from the kit. fog lights arent...


Check your instructions with the fog lamps, I believe you will need to take your car to a dealer to have them activate the fog lamp driver in the Totally Integrated Power Module.

Jan 23, 2011 | 2008 Dodge Charger

1 Answer

99 gmc denali dash light, parking lights, tail lights, and dash light dont work. Interior lights, brake lights, blinkers, headlights work Turning on the headlight switch blows number 15 drl-fog fuse...


You have a short to ground somewhere in the drl-fog lamp circuit. Check for obvious wiring connector or wiring to drl & fog lamps. check wiring for pinched or broken wires coming from sockets. If you don't find problem, you can trace wiring from lamps to main harnesses and hopefully find source of short.
hope this helps.

Mar 02, 2010 | 1999 GMC Denali

1 Answer

I want to add fog lamps to my '01 Mustang convertible. I can get the lamps, brackets & dash switch from Ford at reasonable prices. My question: Does the existing wiring harness include wiring for the...


i dont think current wiring harness is set up for fog lights but fuse box should have a spot for relay and fuse (although it may or may not have metal leads installed) if your getting parts from ford i ask them if they have wiriring harness for it
if you decide to wire them in yourself i would HIGHLY recomend u put a relay in the system if you dont you will have to use bigger wire tho the whole sytem. with a relay u only have use the bigger wire from relay to lights. You will also have to use a heavy duty switch u will burn up factory switch if dont use a realy

Feb 17, 2010 | 2001 Ford Mustang

1 Answer

How to replace fog light bulb on an '03 Jeep


There is a small square "trap door" in each wheel well directly behind the fog lamps. You can pry it open and access the fog lamps. They just twist loose.

Feb 11, 2010 | 2003 Jeep Wrangler

1 Answer

Need a fuse box diagram to wire in fog lights


Fog lamps are installed on the front bumper. The switch is located to the left of the steering column on the dash panel. The fog lamps are turned off by the circuit relay when the high beam driving lamps are turned on. The circuit relay is located on the right front wheelhouse panel near the blower motor.

Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element
See Figure 1
558610d.gif
Fig. 1: Exploded view of a fog lamp assembly

  1. Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
  2. Remove the reflector assembly from the lamp body.
  3. Remove the bulb holder from the assembly. Remove the element from the bulb.

DO NOT handle elements with your bare hands, always handle with a clean cloth. Oil from your hands will cause the element to fail.
  1. Installation is the reverse of removal.

Fog Lamp Switch
The fog lamp switch is removed and installed by simply prying the switch from the instrument panel and unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT

  1. Position the vehicle on a level surface, facing a wall approximately 25 feet away. Remove the lamp stone shields and loosen the adjustment nuts.
  2. Turn the fog lamps ON and adjust as follows:
    1. Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
    2. Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
  3. Install all previously removed items after turning OFF the fog lamps.

1995 Cherokee Chassis Schematic
8e08df0.gif

www.autozone.com

Aug 11, 2009 | 1995 Jeep Cherokee

1 Answer

Plugging after-market fog lamps in firewall of 2007 Sierra 1500


Usually there are some areas that have rubber boots for factory equipment/wiring to pass threw. Cut a small notch in the boot and pass your wire threw.

Dec 25, 2008 | 2007 Scion tC Coupe

Not finding what you are looking for?
1999 Jeep Wrangler Logo

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...