Question about 1999 Toyota Corolla

Open Question

Inner tie rod replacement

Need boot removal and rod replacement instructions

Posted by on

6 Suggested Answers

  • 1861 Answers

SOURCE: inner tie rod ends on a 2002 toyota celica

First, you do NOT have to remove the rack to replace the inner tie rod ends. Second, If you want a .pdf regarding the procedure, I'll be glad to send it to you. But, the tie rods just screw off. Whatyou WILL need to do is get a good front-end alignement after you replace the inner tie rod. If not, you will destroy your tires. Alignment is critical to minimize tire wear on Celicas.

Posted on Nov 13, 2008

  • 124 Answers

SOURCE: I,ve disconected the tie rod

If it is the inner tie rod you are working on it need to be threaded out on some you can get with a wrench but most you will need an inner tie rod tool. Look at your replacement tie rod you will see the threads and two flat spots that is where the wrench goes. Please rate.

Posted on Dec 13, 2008

  • 507 Answers

SOURCE: How to replace Inner Tie rod on 1994 Chrysler Town & Country?

222,000 miles? that's a good vechile so far! anyways, do some price checking. new rack and pinions come with the inner tie rods. so if it's like 50 more for the whole assembly, i would but if not, it's up to you. i've changed some rack and pinions on vechiles that were under 150000 due to major leaking. and if you put just new rods in, if it dose start leaking later, you'll get new inner rods again with new system you'll just be paying labor and alingment charges again. so again, my OPINION is if I'm going to keep it for a while and if it's COST effective, just to do the whole unit.

Posted on Mar 07, 2009

  • 4369 Answers

SOURCE: How to change inner tie rod ends?

if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------

  • The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
  • If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
  • If the leak is not corrected, replace the fitting seals.
-------------------------------------------------------------
f12ee38.gif
-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal
  1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
  1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
  1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal
  1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .


    13b4d70.gif

  1. Support vehicle with jackstands under front jack pads.
  1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
  1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
  1. Disconnect heated oxygen and catalyst monitor sensors.
  1. Support flex pipe.
  1. Remove bolts and disconnect flex pipe from the converter.
  1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
  1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
  1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
  1. Remove rear subframe-to-body retaining bolts.
  1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
  1. Remove heat shield band and fold shield down.
  1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
  1. Place a drain pan under vehicle and remove line fittings.
  1. Remove power rack and pinion steering gear through LH wheel well.
  1. Remove and discard the O-rings.
Installation
  1. Install new Teflon® O-rings on line fittings as outlined.
  1. Place steering gear retaining bolts in steering gear housing.
  1. Install power rack and pinion steering gear through LH wheel well.
  1. Install power steering line fittings to power rack and pinion steering gear.
  1. Position power rack and pinion steering gear into front subframe.
  1. Install ******** heat shield.
  1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
  1. Install LH front stabilizer bar. Refer to Section 04-01 .
  1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. Raise hoist until rear subframe contacts body.
  1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
  1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
  1. Connect heated oxygen and catalyst monitor sensors.
  1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
  1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
  1. Remove jackstands and lower vehicle.
  1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
  1. Check system for leaks and proper operation.

Posted on Apr 15, 2009

  • 366 Answers

SOURCE: Repalcement process on inner tie rods 05 silverado

undo bolts on inner and outer tie rods,u might need balljoint fork separator or 2 jaw puller to take them off of relay rod and steering knuckle,measure lenght of tie rod,loosen tube clamp and undo tie rod from tube,when installing make sure lenght is the same as before or wheel alignment will be off!

Posted on May 12, 2009

Molson02536
  • 3854 Answers

SOURCE: how difficult to replace inner tie rod end on 06 silverado 2wd?

Not that hard, just spray the tie rod sleeve with WD40 night before and let it soak in. Remove the collier pin and and nut and hammer the old inner tie rod end out of the Track rod with a 5 pound sledge hammer. Remove the inner tie rod end from the sleeve and don't forget to mark the distance so you can place the new tie rod end at the same length. Reinstall the inner tie rod end to the Track rod and tighten the nut and replace the collier pin with a new one. Grease the fitting and go for a test drive, if the truck does not wonder then your good to go with out a alignment. Good luck and hope this helps, Note, make sure you have to right inner tie rod ends. Each side has different thread rotations.

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

2 Answers

Need to replace inner tie rod on a 1998 ford ranger two wheel drive , driver side . engine size is 2.5. do i have to take outer tie rod off as well?


webbraymond2, Yes, you have to remove the outer tie to access the inner tie rod. When you do this, count the rotations of the tie rod as this will have to be replaced when the new inner tie rod is installed. Counting the rotations will allow you to put the outer tie rod close to where it was when you started the job. You are changing the toe setting when you have to replace either the inner or outer tie rod. You need to access and remove the jamb nut and boot before you can access the inner tie rod and this is why the outer needs to be removed first. A wheel alignment is advised after you finish the job. Good luck with this.

May 28, 2011 | Ford Ranger Cars & Trucks

1 Answer

1999 ford falcon futura change steering rack boot


To replace the boot first you have to remove the outer tie rod end form the spindle asembly. You will need a pair of wire cutters to grab the cotter pin that holds the nut in place. After the nut is removed whack the spindle where the tie rod goes into it with a ball peen hammer and the tie rod end will pop right out. Do not hit the tie rod end on the threads or you will have to buy a new one. Now you have to seperate the outer and inner tie rod ends. There is a nut holding the two tightly in place and a notch in the inner tie rod end to put a wrench on so the inner will not spin when you spin off the outer tie rod end. Mark the threads before removal so you can put it back where it was adjusted before. Loosen the nut and spin off the tie rod end. Now for the boot. There are two clamps on the boot you need to remove a small clamp and a large clamp. With the wire cutters grab these clamps and wrok them off. The new boot will come with new clamps. Always replace the clamps. Now just slide the boot off. You will need to remove the lock nut to change the boot so make sure you mark the threads on the inside so you do not wipe the mark off when you remove the nut. Now just reverse the process to reassemble. Be sure to put it back where it was adjusted before. Make sure to use a new cotter pin. When you reinstall the nut back on the outer tie rod end it is important to tighten it about one turn past snug and line up the cotter pin hole by tightening the nut do not back off the nut to align the cotter pin or it will come loose and ruin the spindle. Not that was not so hard was it. Thanks for visiting the site.

Nov 19, 2010 | Ford Futura Cars & Trucks

1 Answer

How to install inner and outer tie rods on a 2004 Chrysler Pacifica - I waqs told buy a trusted local mechanic that I need to replace 3 of the 4 tie rods. Might as as well replace all 4, but how hard is it...


You will need to rent or borrow in inner tie rod tool but here are the directions.
1. Break the jam nut on inner tie rod to outer loose.
2. Remove nut from outer tie rod attaching it to steering knuckle.
3. Use hammer to get tie rod out of knuckle.
4. Unscrew outer tie rod then jam nut
5. Remove clamp from boot and slide off inner tie rod.
6. Using side cutter or hammer and chisel break off metal clamp on the inside of inner tie rod boot.
7. Using inner tie rod tool, unscrew inner tie rod from rack and pinion
8. Reinstall parts and have it aligned

May 06, 2010 | 2004 Chrysler Pacifica

2 Answers

One of the steering rods that goes from the rack to the right tie rod is bent. Can I replace the rod or must I replace the entire rack?


you can replace just the tie rod yourself although you do need a special tool but you should be able to get it at any parts store just take the outer tie rod loose from the steering knuckle remove the rubber boot from the inner tie rod and get the proper size tool to fit he nut and remove and replace the inner tie rod and install in reverse order make sure to count the amout of turns that removed the outer tie rod and reinstall the same amount of turns then afterward the car needs to be aligned

Apr 13, 2010 | 2000 Ford Focus

1 Answer

I just bought a 93 honda civic and I took it to goodyear and they said I needed my tie rods tightend is there a way I can do it myself?


Yes. If it's to correct alignment, the inner tie rod shaft has to be moved into your outer tie rod and then tightened. this is all done from the wheel area.

If it is to correct play in the steering, then this should apply.

The inner tie rod connection to the Rack unit is hidden by the rack boot which will need to be removed from the Rack unit but not completely removed from the shaft, just pushed over out of the way while working on the inner tie rod adjustment. The large nut on the end of the inner tie rod will have to be loosened & checked, for any damage, then reinstalled & tightened to the correct amount necessary to cause sufficient drag on the inner tie rod but not too much to restrict it during normal use.

You may even want to consider a remanufactured Rack unit if you have too much slack in the steering. Tightening the Inner Tie Rods doesn't replace the seals & rebuild the remainder of the Rack & Pinion, yet these parts all have the same amount of wear on them that the Inner Tie Rod does.

Manuals available w/step by step instructions for your vehicle at parts stores. good luck

Feb 15, 2010 | 1993 Honda Civic 4 Door

1 Answer

How too change inner tierod on 2005 pontiac g6


If you have electric steering(no power steering pump)you have to change the entire steering gear assembly as no part is available.If you have the system with a pump a part is available.In order to change the inner tie rod you would loosen the 21mm lock nut on the tie rod.remove the 18mm nut on the outer tie rod and spin off after removing the outer tie rod from the steering knuckle.Remove the nut and the inner and outer clamps on the tie rod boot.remove the boot.You would then need a special inner tie rod tool to turn the threaded inner rod from the steering gear.

Oct 17, 2009 | 2005 Pontiac G6

1 Answer

I need to replace the inner tie rods on my 97' conti......need a diagram of how to and any other info pertinent to the job - Bair


If this is a rack and pinion type steering, in order to remove the inner tie rods you will first have loosen the jam nut at the outer tie rod end,next unbolt the outer tie rod from the steering knuckle, unscrew the outer tie rod end off (be sure to count how many turns to remove), next remove the inner bellows boot (black boot) from the tie rod / rack and pinion, next is to unscrew the inner tie rod from the rack assembly (the do make a tool for this to make it easier) but if you do not have the tool,you can sometimes use a big pair of channel locks or a big enough wrench to fit on the fitting on the inside of the inner tie rod, and just unscrew the inner tie rod (normal left=loosen, right=tighten). Hope this helps. Would also recommend having it aligned after you are finished.

Mar 12, 2009 | 1997 Lincoln Continental

2 Answers

Tie rod problem 98 Dodge


There is a tool that you can use that will make it easier for you. To get to the tie rod end, remove the wheel and take the outer tie rod end loose from the hub. You will have to use a hammer and hit the socket where the end goes into the hub to free it up. Once you have the tie rod loose from the hub, loosen the nut behind the outer tie rod end. Count the revolutions as you unscrew the outer end off and write te number down so you will know how far to put it back on. This will save your alignment. Now, the end that is still there is your inner tie rod end. You will have to undo the bellows boot to get to the nut. The tool will slide over the end and secure onto the nut. Now you just unscrew this and replace with you new inner tie rod end.
Please remember to rate this fix.

Feb 16, 2009 | 1998 Dodge Grand Caravan

2 Answers

How to change an inner tie rod end on a honda civic 1.5


you must remove or slide the inner tie rod boot outward on the rod and then thread the tie rod out of the steering rack. there is a section of the tie rod on the inside of the ball joint that has flat spots to get a open end wrench onto. to check your tie rods, simply jack the wheel off of the ground, grab the either side of the tire, and wiggle it towards and away from you. if you feel any play at all the tie rods must be replaced. also a god indication is when the front tires start to wear excessivly on the inside or outside edges.

as for the cv axle, it has a retainer ring on the end of the splined shaft. all thats reqired is to seat the splines in the transaxle (transmission) and the tap (shouldnt take too much) the outer end of the axle with a mallet or hammer. it will pop into place.

if you have any questions email me at thadoggma420@hotmail.com

Oct 03, 2008 | 1988 Honda Civic 2 Door

Not finding what you are looking for?
1999 Toyota Corolla Logo

Related Topics:

510 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...