Question about 1996 Cadillac DeVille

1 Answer

Codes I am getting codes RS0061, RF2560, IP1552, IP2419. What do they mean and how can I erase them once the problem is corrected?

Posted by on

  • 1 more comment 
  • paullaubi Nov 01, 2008

    Thanks for your help. The problem is that we are retired and on limited income. i will get a price from dealer before venturing into never, never land where the caddy dealers seem to dwell.
    Thanks again you've been a big help.
    Paul

  • yescas Apr 21, 2009

    code ip1552 shows. what does dat mean

  • Paul Hitchings
    Paul Hitchings May 11, 2010

    What kind of car do you have? Also, you need to disconnect the battery and/or CPU fuse to reset the codes. Disconnect either of the two previous items for 30 seconds and reconnect. If the codes are back, the problems never left.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 62 Answers

RF2560 -  Remote Keyless Entry Validation fault - dealer fix RS0061 -  Right front position sensor fault - dealer fix IP1552 - KAM error (keep alive memory) power loss to instrument panel? - dealer fix IP2419 - instrument panel (unsure) 
I would talk with a dealer re fixes to all these codes. Unless you're a great mechanic and understand advnanced principles of electronics, let the experts fix your expensive (or to fix at least) car.
Sorry not to have better news. Community colleges offer cheap classes in auto repair...
Paul

Posted on Nov 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code po107


Just because your getting a code from a sensor doesn't mean the sensor is N/G. The MAP sensor reads the manifold air pressure, that can be anything from a vacuum leak, elec short, bad plug/wire, miss, gasket and the list goes on. It can be a bad sensor too, don't get me wrong. Does it run rough, hard start, did you ck the emissions? First things first Vacuum leaks & gaskets are popular. Once in a while I cross paths w/ a cracked manifold. Don't throw your $ out the window, Do it once & do it right. Good luck

Oct 24, 2015 | Cars & Trucks

2 Answers

My car is stuck in limp in mode I have replaced speed sensor and I'm getting p 0700 it's a 02 stratus I was told if I have the codes reset that the car should shift correctly


Incorrect information the code is because of a system malfunction and that is what is causing the shift problem. Resetting the code does nothing. Your code is transmission control circuit malfunction.

Sep 22, 2015 | Cars & Trucks

1 Answer

How can I reset the crankshaft position sensor on BMW 328i 2008


If you have replaced it and it is working correctly, you can just erase the code or wait for it to shut off once you have driven it for a few miles. if you erased / reset it and it comes back, there is still a fault.

Oct 11, 2014 | 2008 BMW 328i

1 Answer

Trouble codes p0134 also p0154


I'm going to assume this is for the Blazer.
Code 134 means the front O2 sensor for bank one is not sending any data or is not working correctly.
Code 154 is the same thing for the front sensor on bank two.
The sensors and wiring harness would need to be checked out. Once the problem is fixed and the codes erased, the warning light should stay off.

May 18, 2013 | Cars & Trucks

1 Answer

I just changed the o2 sensor bank 1 sensor 2


Well, FIRST let me ask you what does B1S2 mean to you?

Bank 1 means it is the same side as the #1 Cylinder
Sensor 2 means it is the Sensor DOWN STREAM or AFTER the Catalytic converter..

With this being said... Are you sure you changed the correct O2 Sensor?

The Second thing that I need to tell you is this... Because it says O2 Sensor. Majority of the time it is the Sensor, but it could be other things... Broken Wire, Computer, Fuel Pressure and if it is DOWNSTEAM... Then it could be the CAT.

THEN.... I looked up and see that it was a HONDA and low and behold it occurred to me...

WHERE DID YOU GET YOUR O2 Sensor From? (this is where I saved so many people)...

Honda has made the variables so TIGHT that an AFTERMARKET O2 Sensor does not work....

If you have a ULEV Vehicle (Ultra Low Emissions Vehicle), you are pretty much forced to get the Sensor from Honda....

That would be my FIRST GUESS.... Get the HONDA Part...

Apr 05, 2013 | 2003 Honda Odyssey

1 Answer

What does code 6-4 mean


Bank 2, sensor 3 is having a high reading. This would be the last sensor after the Catalytic converters. Also have the Code erased by going to Autozone, Oreilys, or Advance autoparts and getting the free scan.

These parts places can sell you the correct part. You will also need a special socket to remove and replace the part.

Dec 16, 2011 | 2008 Mazda B Series Pickup

1 Answer

My jetta's timing belt broke, and so we the part and put it in but didnt change the water pump. it still wont start and is making a funny noise when we try to crank it. now i put it on the machine that...


You need to erase the code for it to start,If it still wont start chech the timming marks again with cylinder #1.,you might have top dead centered cylinder #4 by mistake, when you did the belt.
erasing the code first might work because a code 1582 could have more or less filled up the sensor banks when the belt broke ,causing the computer to shut down everything.
If after you erase the code you get the same code then you have to re-align the timing markg because the position causes the computer to overload trying to correct the mecanical problem it has to deal with because of a miss alignment of the valve train.
Good luck,Gary

Sep 15, 2011 | 1997 Volkswagen Jetta

1 Answer

My nissan frontier crew cab 2001 SERVICE ENGINE SOON light on the dashboard kept flashing. Have serviced the engine, but the light won't stop flashing. Thanks


That means you have a failure somewhere in the system (Powertrain, Chassis, Body, Network). Just because the engine was serviced doesn't mean anything. You need to have the diagnostic codes pulled to determine what is causing the light to be triggered. Then correct the problem and the light will go out. If you just erase the light or code it wont solve anything.

Jan 16, 2011 | 2001 Nissan Frontier Crew Cab

2 Answers

Can I reset a P0456 code on Chrysler Pacifica 2004 myself


That code usually means your gas cap is not tight enough or if it is the seal on the cap is bad and not sealing tight enough. You can fix the problem by replacing the cap with a new OEM one from the Dealer. Aftermarket caps are not recommended. Sometimes once you have a new cap installed the code will go away by itself. You will need a OBD II scanner to erase the code, you can go to AutoZone and they can read and erase the code for you.

Jun 16, 2010 | 2004 Chrysler Pacifica

1 Answer

My engine light will not trun off on my mustang and itpassed saftey and etest how do i get it to trun off


You must First Be SURE that there is NO TRUE FAULT with the VEHICLE, meaning that if there is Fault codes they must be Corrected, as in Part Replacment for this Light to turn off and "STAY OFF". If this has ALL Been DONE Correctly,Then Even the Cheap CODE SCANNER can ERASE / RESET this Light, or You Can DISCONNECT the BATTERY for 1 Minute-<<(( I Do this for 1 hour) myself as SOME ECM's Will HOG RESIDUAL CURRENT thus Providing it with Enough Current to KEEP this CODE Alive in ECM for Longer than a few Minutes.

Nov 17, 2009 | 1994 Ford Mustang

Not finding what you are looking for?
1996 Cadillac DeVille Logo

1,383 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...