Question about 1985 Chevrolet Corvette

1 Answer

85 corvet i cant get the panal off my battery

I cant get the panal off my battery what tools do i need

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You need a torx wrench. Screws are on the bottom and back of front fender.

Posted on Nov 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 corvete tpi gas getting in oil pan change the fuel reulatorstill getting fuel in oil pan is this a fireing problem


Check fuel pressure regulator vacuum hose if it's got gas in it the
fuel pressure regulator is bad and will need replaced. Will get into oil through vacuum hoses

Apr 08, 2014 | Cars & Trucks

1 Answer

Installing new seats in a 2008 corvet need directions


raise power seat to max height. remove the covers on floor bolts and remove seatbelt anchors. disconnect wiring under seat

Oct 11, 2013 | Chevrolet Corvette Cars & Trucks

1 Answer

Ok well Im having problems getting the AC/Heater to work correctly. The air will blow out of the vents that is supposed to be used for the defroster, but not anywhere else. What could this be, I have been...


hi
check the back of your heating/a/c control panal as these unit are mostly controled by vacuum air, there may be a leak at the panal or no vacuum air is being suppied to the panal these controls are designed to go into defrost moded if vacuum is lost

andy snow

Feb 29, 2012 | Cars & Trucks

1 Answer

I cant seem to remove the radio in a ford e350 i did buy the tool for this but with no luck is it bolted or do i have to remove the dash panal


Do you have two of the tools needed to remove the radio? The tool should be pushed into the holes until it stops then you want to slightly press outward to make the clips pop so the radio can be removed...I have used skinny screwdrivers to accomplish this in the past due to unavailability of tool..most of the time you need to have both sides pressed in at the same time to remove otherwise one side will pop then when you go to other side the previous side will re-lock back in

Jan 08, 2011 | 2002 Ford E350

1 Answer

I've put a new alternator on and it still want charge. The battery drians when the truck is running. just wondering if there is a relay of some sort stopping the alternator from charging.


Yes there is a relay for the ECM system but its not the problem its located inside passanger side under kick panal with the computer module.This is a short in the electrical system its likely the starting motor it may still work but its still shorting Disconnect the negitive battery cable take a mulity meter set it to 20 volts DC touch the red lead to B + red cable on battery and the black lead from the meter to good engine ground block frame where ever you get a solid ground. See if you read voltage if you do you have a short and if its 5 volts or more its likely the starting motor. I have an 85 and have been through this also have factory manuals if you need more help just give me a fax # to send it to pier_j

Dec 21, 2010 | 1987 Ford Ranger

1 Answer

Do you remove the heater core from inside the vehicle or outside under the hood


An 88 F150 on my 85 it was a pisce of cake you do it from the inside on yours ther should be an axsess panal for it passageners side to the middle remove the panal and its right there disconnect the hoses out side and take it out it took my 20 minutes to remove and install last time i did it on that vehicle and 85 s are the sames as 91s so you should have an easy time of it

Nov 24, 2010 | 1988 Ford F 150

1 Answer

I cant take off the door panel on the driver font side door...can u tell me how


first remove the screws from inside handle, take off window crank, if you do not have a tool to do this, a clean rag works well. just move the rag back and forth behind handle to knock off handle clip. or you can go to any parts store and buy a clip remover for handle.when all is removed. first put window all the way down, panal pops off. there are clips to hold it on, just use a removal tool or a flat blade to take off panal. when putting handle back on just put clip on handle and push it back on.

Oct 08, 2009 | 2000 Chevrolet Malibu

1 Answer

Door panal


there's a tool to do it . but if your real carefull you can do it without it. 1st remove all the screws on doors armrest , then side a flat head screw drive in between door and panal slide it around till you feel the plastic buttons then pry slowly, repeat till you get them all.

Oct 21, 2008 | 1999 Chevrolet Malibu

1 Answer

37 chevy


give me all the information for the corvete engine and i will tell you how to plug it in, it might take a little be before i get back with an answer because i'm a bussy mobile mechanic, but i will try to be here on the 11th of this mont, i need year and all the info you have from the origina corvete where you pull the engine from,

Jun 08, 2008 | 1998 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...