Question about Mitsubishi Pickup

1 Answer

Need diagrams to show how to change rear wheel bearing 1990 mitsubitsi L200 4x4 petrol

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 44 Answers

You might try you local library, You should be able to find a book on your make and model, that will have the instruction in it you need to do the job.

Posted on Nov 01, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Reg Number OY03HZN Honda CRV Petrol 2003 Overheating rear off side wheel?

check for correct bearing preload adjustment
check that the hand brake was properly adjusted off before the pads were fitted as if not on the first application the pads will stay on the disc
the problem is in the workmanship and procedure for the repair

Nov 16, 2015 | Honda Cars & Trucks

1 Answer

How do you change rear wheel bearing

THE FSM covers this and,
see these links,

the toy Corolla is the same car. so .... same words to fix.

Jul 29, 2014 | 1990 Geo Prizm

1 Answer

Left front passenger side cv joint for 1990 quattro has noise, is it easy to fix

Can be a messy job. Is the flexible rubber boot over surrounding the joint split and spewing forth oily muck. Remove wheel cover and bearing oil cap in the middle. slacken the wheel bearing nut a turn or so. Jack the car until the wheel is off the ground and remove the wheel. Remove the bearing nut and push (tap with wooden block the drive shaft inwards to disconnect it from the hub. Try turning the steering wheel if the shaft does not go back all the way to allow the stub to be released. You may have to undo the track rod end to give you extra clearance. Remove the split boot (gaiter) and wash the bearing clean of all oil and dirt with petrol so that you can inspect it thoroughly. The stub axle should also come free of the tripod ended drive shaft. If the metal shows bad signs of wear you will need to replace the bearing assembly. Repair kits for the replacement of boots contain packs of appropriate grease. To get the boot on easily you will need to have access to a boot cone tool. The wide end fits over the joint with the narrow end away from it. Lube the end of the narrow end of the boot and slip it over the narrow end of the cone. By forcing it along the cone the narrow end spreads wide enough to clear the joint and sit back down on the drive shaft. Fill the joint with new grease and seal the boot ends with a crimping tool. Wear neoprene gloves at all times as this is one filthy job

Jun 24, 2010 | 1990 Audi V8 Quattro

1 Answer

Rear whheel bering repair

need to find rear wheel bearing isuzu bighorn 3.1 (*** import)

Oct 28, 2009 | 1985 Isuzu Trooper

1 Answer

Need to see a diagram of how to change rear wheel bearing on my 320 touring 1996

BMW uses CV shafts for the rear drive axle, the wheel bearing there is a pressed in factory sealed bearing and not removable other than using a press to remove it, to press it you will need to remove the lower control arm.

May 22, 2009 | 1999 BMW 323 Series

1 Answer

I need a free diagram of rear wheel bearing replacement

The question you asked me to clarify was really quite simple..... I needed a diagram of rear wheel bearing assembly for a 2000 Dodge Grand Caravan 3.38 litre, 6 cylinder, 2 wheel drive vehicle. You couldn't provide me with a diagram so I took the wheel off looked at the old one then the new one and just did it myself. Thanks for not helping.
Stormin Norman

Nov 10, 2008 | Hyundai Excel Cars & Trucks

1 Answer

There is a whistling noise coming from drivers rear side wheel and my car is drinking petrol like its going out of fashion, also the remote central locking key is not at all efficentent (have change...

needs tune up to solve drinking gas. carb prob out of whack. whistling may be wheel bearing. jack car up and try wobble wheel top to bottom ie try and tilt it. shouldnt be any movement or clicking. if so replace bearings.
remote key may need re-programming

Aug 07, 2008 | Alfa Romeo 156 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8825 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides