Question about 1993 Porsche 928

1 Answer

Porsche 928 I am having trouble removing rear breake light assembly, need to replace bulb

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 13 Answers

Open trunck , look behind rear panel look for plastic nut ,loosen and pull on tail light .

Posted on Jan 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

How do i remove the battery from porsche 928


Remove rear carpet. Remove spare tire in recessed tire compartment. There will be a small hatch with a plastic white lever that you have to swing open. Once the door is open, remove ground (black) first, then the positive red side. Clean terminals and also clean ground to rear hatch from battery.

Oct 06, 2014 | 1986 Porsche 928

1 Answer

Where is the fuel pump on a 1987 porsche 928 S4?


Hello there

The fuel pump is located in the rear of the car right next to the fuel tank.

From behind the car you need to remove protective (L shape) metal cover (right rear)and then you will see the fuel pump.



let me know if you more info

proporsche

Aug 14, 2011 | 1987 Porsche 928

1 Answer

Replacing rear brake light bulb


Carefully remove the two trim plugs from each tail light assembly with a small knife blade. Remove the two hex head bolts on each assembly. Insert a small paint stir stick (soft wood won't damage paint) between the fender and the tail light assembly. Gently pull the opposite (inside) side of the assembly off. The paint stick allow the assembly to pop off the ball and socket pin holding the outside part of the assembly in place. Unplug the power plug by releasing the retainer clip. Unscrew the large black plastic nuts on the back of the assembly with a very large screwdriver, if they can't be turned by hand,and remove. Replace burned out bulb/s and reassemble in reverse order. Remember the trim plugs have two prongs on them. Position them with the prongs and the direct top and bottom and press into place.

Apr 09, 2011 | 2004 Porsche Cayenne

1 Answer

Left brake light dont work when brake peddel is applied


Replace the bulb,
1. Open the lift gate on the rear of your Blazer or drop it if you have the tail gate that folds down. Locate the screws on the inner edge of the lift gate frame. There are two screws--remove them with a Phillips screwdriver.
2. Slide the taillight assembly out of the rear of the truck, being careful to not break the locating tabs on the rear of the housing. Locate the bulb sockets on the rear of the taillight assembly.
3. Rotate the light bulb socket counterclockwise about a quarter turn to unlock it from the taillight assembly. Pull the socket straight out of the assembly with the bulb attached to it.
4. Remove the bulb from the socket by pulling it straight out of the socket. If you are removing the entire assembly from the truck, remove the remaining sockets from the rear of the taillight assembly, lay them aside and remove the assembly completely.
5. Reinstall everything in revers and don't for get to *** some grease to your socket before you place the new bulb in place and test the operation of the new bulb before you reinstall the tail light.
Thank you for using fixya and here is the bulb you need for the trail light.The 1999 Blazer uses a 3057 bulb available at most auto parts stores.

Apr 29, 2010 | 1999 Chevrolet Blazer

2 Answers

Replace rear window brake light bulb


I just had to do this, and it isn't all that easy or quick. First, gently work the gray, carpet like cover loose from the area around the tail light ,(this may give you a little trouble). Once you have done this, you will see three silver nuts. These must be unscrewed. The lower left nut must be accessed through a hole next to where the trunk lid fits. (The screws are permanently attached to the lens housing so will not drop into obscurity when the nuts are removed). After removing the nuts, GENTLY work the lens housing away from the car. You may need a screw driver to unseat the housing, but just be gentle.

You will find three bulbs inside the lens. The brake light bulb is on the lower right side. Simply pull the old bulb out and insert the new one.

Just reverse these directions to reassemble the housing.

May 04, 2009 | 2002 Lincoln LS

1 Answer

How replace break light bulb in on a4 2005


Replacement of any bulb in the Tail-light assembly is easier then one thinks.

First thing you need to do is gain access to the trunk area. At the top of
the tail-light area inside the trunk is a small circle that needs to be
opened to expose the bolt that you need to remove.

WARNING: Be careful not to loose this bolt or you are going to have to take
apart your trunk interior to retrieve it.

After the bolt is removed the Tail-light assembly will pull out as follows;
Left side: pull out the right side of the assembly
Right side: pull out the left side of the assembly.
The out side of the assembly is held in place by 2 or 3 small nipples.

There will only be one cable that is connected to the assembly. This does not
have to be removed unless you really want to. On both sides of the assembly
there are 2 clips that hold the light plate to the break light lens. After
the clips are loosened the whole light bulb assembly can be removed and the
bulbs replaced.


Restoring the Break-light assembly.

After you have replaced your bulbs and re attached the the bulb assembly, you
will have to first fit the nipples on the outer side of the assembly then
push the inter side into place. Replace the bolt and tighten. You are done.

Jul 14, 2008 | 2005 Audi A4

1 Answer

1979 Porsche 928 head lights...


If you still require this information I can email you the79 wiring diagrams bruce.mahony@three.com.au

Jun 04, 2008 | 1985 Porsche 928

Not finding what you are looking for?
1993 Porsche 928 Logo

Related Topics:

306 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Dave  C
Dave C

Level 3 Expert

1050 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...