Question about 1993 Nissan Maxima

1 Answer

1993 nissan maxima drivers door lock cylinder

Customer broke key in drivers door lock , removed cylinder to remove broken key and reinstalled but second key wont turn cylinder then installed new cylinder but it wont turn either w/new key

Posted by on

  • Jason Schoonmaker
    Jason Schoonmaker May 11, 2010

    Have you checked the linkage for binding? Sounds like something is jammed up and not allowing the key to turn the cylinder.



    Does the original 2nd key turn the other cylinders?





    Nissan Scope Technician- 10+ years experience in Nissan dealership.


×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 21,949 Answers

You have made a boo boo somewhere,are you a certified city and guilds technician,if not then you shouldnt be repairing customers cars

Posted on Dec 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I program a 2004 Nissan Maxima key fob?


Free Nissan Keyless Remote Programming Replacement Key Keyfob Maxima...

2004 Nissan Maxima Key Fob Programming Instructions

2004 Maxima

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.
  1. Close and lock all doors with the driver's side power lock/unlock switch.
  2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast, system will not enter programming mode.
  3. Insert key into the ignition cylinder and turn to the ACC position.
  4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful.
  5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver's side power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should flash. Repeat this step for each transmitter (including any existing transmitters).
  6. Turn the key to the OFF position, remove keys from the ignition,
    unlock doors using the driver's side power lock/unlock switch and open the driver side door.

Mar 09, 2015 | Nissan Cars & Trucks

1 Answer

How do I install a drivers side door lock cylinder on a 99 Nissan Sentra?


Take the door panel off and remove the linkage and retainer for the lock cylinder. If you just need it rekeyed take that part to locksmith, so it will match the other cylinders and work with your key

Jan 08, 2015 | Nissan Sentra Cars & Trucks

1 Answer

How can I replace the ignition lock and the drivers door lock on a 1993 300zx?


You will probably need to drill out the center of the ignition lock cylinder to remove it without the key. Start with a small bit and make sure you drill straight into it and then use a little bit bigger drill bit. Keep doing that until you can turn the key lock cylinder and you'll be able to remove it.

May 06, 2014 | Cars & Trucks

1 Answer

How do you remove an ignition starter to a 1993 nissan pickup? I broke half my key off in the ignition and now I'm on a mission to either replace it, or remove the key. Any suggestions?


call a locksmith, they do this kind of job everyday. tell him you want th ebroken key removed fron the Ignition switch lock cylinder. Not igntion starter.

Sep 06, 2011 | 1993 Nissan Pickup

1 Answer

Key Broke


To get a new key for your car, you will need to have a lock cylinder removed and taken to a lock smith to have it decoded so a key can be made. The easiest cylinder to remove is the truck.

thanks Jay!

Jul 30, 2009 | 1995 Nissan Maxima

1 Answer

Key broke off in ignition lock cylinder. Can't remove cylinder.


Non-Functional Lock Cylinder
  1. Disconnect the negative battery cable.
  2. Remove the upper and lower steering column covers.
  3. Insert a 0.125 (3.17mm) drill bit in the hole at the top of the cylinder housing and drill out the retaining pin. NOTE: Be careful not to drill into the lock cylinder housing.
  4. Pull out the lock cylinder.
  5. Clean out all the metal shavings and check the tube for damage. If damaged, the housing must be replaced. To Install:
  6. Turn the new lock cylinder to accessory position and while pressing the retaining pin in, insert the lock cylinder into the housing.
  7. Turn the key to the OFF position the release the retaining pin.
  8. Try the lock cylinder operation in all positions.
  9. Reinstall the steering column covers.
  10. Reconnect the negative battery cable.

Jun 25, 2009 | 1999 Mercury Cougar

1 Answer

I need to somehow reset my factory alarm on my 1995 Nissan Maxima


this is how most nissans program the key fobs.
get in the car and manually lock the drivers door with the door switch.
put the key in and out of the ignition about 10 or 12 times until the hazard lights flash once.
turn the key to the ignition setting so all the dash lights are on,but do not start the car.
click the lock button on the remote fob.the hazards should flash once to confirm.
turn off ignition and remove the key.
unlock the drivers door and open the door.
the remote should now work.
if that does not work,the dealer can reprogram the fob with the obd diagnostic system.

May 26, 2009 | 1995 Nissan Maxima

1 Answer

I can't get my 1996 Maximas drivers side door to open. It's like it's locked


hi it sounds like either the lock broke or the rods in side of your door have fallen off.you will have to remove the door panel off with the door closed to manualy move the lever in door to get open.it is verry hard with door closed to get door pannel off

Feb 02, 2009 | 1996 Nissan Maxima

1 Answer

Abs module


www.bba-reman.com.

Jun 19, 2008 | 1993 Nissan Maxima

Not finding what you are looking for?
1993 Nissan Maxima Logo

Related Topics:

414 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...