I have a 2001 aurora and the DIC doesn't display anything (but the buttons work, since I can change between km & miles) and the heated seats don't work - push the button the light comes on briefly, then dies off.
Ideas? I also had the remote trunk, fuel door and homelink fail this morning, but I've not had a chance to check the fuses on that one.
If anyone has worked under the hood or in the dash get your copy of what you paid and head to the dealer most dashes boards newer then 95-96 need dealer codes and scanner's to re boot if in safe (anti theft) bit if it starts check the fuses it may be in a seperate connector, your bcm (body control mod) is first to check those computer dashes are very sensative
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Oil Life Monitor Resetting (KD, KE)
The engine oil life monitor will indicate when to change the engine oil and the engine oil filter - usually between 5 000 km (3,000 miles) and 12 500 km (7,500 miles) since the last oil change. Under severe conditions, the CHANGE OIL message may be displayed before 5 000 km (3,000 miles). The vehicle must not be driven more than 12 500 km (7,500 miles) or 12 months without an oil change.
The engine oil life monitor will not detect dust in the oil. If the vehicle is driven in a dusty area, be sure to change the oil every 5 000 km (3,000 miles) or sooner if the CHANGE ENGINE OIL message is displayed.
Reset the oil life monitor when the oil has been changed.
Press the INFORMATION SKIP button on the DIC control panel in order to display the OIL LIFE LEFT message.
Press and hold the RESET NO button until the display shows 100% ENGINE OIL LIFE.
Check your fuses first. Then check to see if you have power to the box under seat. It should be about 3x3 and black I think. If you have power to the box change the box. To check use a test light. make sure the key is on and the button is pushed then probe the wires going to the box. Hope this helps you.
The process for resetting your Tire Pressure Monitor (TPM) is below.
Good luck, let me know.
To reset (calibrate) the system:
1. Turn the ignition switch to RUN.
2. Press the GAGE INFO button on the DIC until
TIRE PRESSURE appears on the display.
3. Press and hold the DIC RESET button for about five
seconds. After five seconds, the display will show
TIRE PRESSURE RESET. If TIRE PRESSURE
RESET does not appear on the display after about
five seconds, see your dealer for service. After you
release the DIC RESET button, TIRE PRESSURE
NORMAL will appear on the display.
The system completes the calibration process during
driving. During the first 10 to 25 miles (15 to 40 km) of
driving, the system will not alert you if a tire is high or
low. After 25 to 100 miles (40 to 160 km), the
system will only alert you about pressure differences of
12 psi (85 kPa) or more. After about 100 miles (160 km)
of driving, the system will alert you if one tire is
10 psi (69 kPa) different from the other three tires.
1995-1999 Oldsmobile Aurora
- To reset OIL LIFE message, press the ENG. button with the ignition on until OIL LIFE percentage is displayed.
- Press the RESET button for 5 seconds.
- RESET will appear and then OIL LIFE 100%.
When the system is on or off, push the ON/OFF button down for three seconds to change the display between English and metric. This will also change the digital screen for the climate control system between English and metric.
The heated seats have relays that run them. Not quite sure where they are located but. That noise is the relay clicking on and off. They are actually pretty loud. Look for faulty connections to and from the relay and check battery power to both sides of the relay.
A common cause for the heated seats to not work is a burned heater element. There is an element under the seat cushion cover, and one under the seatback cover. If either has failed, both will not work.