Question about 2004 Chevrolet Silverado 2500HD

Open Question

2004 Chevrolet Silverado power seat motor

The gear on the up and down motor of the driver seat is stripped. What are the options for repair? Hopefully the motor can be repaired or replaced without replacing the whole seat base.

Posted by on

  • Anonymous Apr 04, 2009

    Im having the same problem in my 1500 GMC Sierra




×

6 Suggested Answers

  • 77 Answers

SOURCE: 2004 Chevrolet Silverado 2500 HD heated seats

I cant give you a precise location, but it will be underneath the seat, probably to one side. It should have a connector that can be disconnected.

Posted on Oct 22, 2008

shaggyrat
  • 1224 Answers

SOURCE: Seat belt repair

first for the switch in window
the window switch is easy to test you just gotta remove switch out of the door leaving it hang there is a way to test with a guaged wire with fuse on it
take the main power wire and touch to the other connectors on the main switch if the window goes down or up the switch is the problem
im suggesting this way first with fuse cause its easier then testing the windows motor inside the door frame the switches should just pop out of the panel with out haveing to take panel off

now the seat belts there are 2 style that are common to chevy
one is inside the molding of the drivers panel you gotta pop off the panels easily and gently to get at the seat belt retractor this will be bolted to the metal under the molding

the other style is in the seat which you gotta unbolt the seat under the top half it will need to be unbolted at the bottom top half of seat
when you pull threw the top section of top half of seat remember to tie a string to the end so that when you pull threw top half the string will be there so you can connect too new belt and pull back threw with ease make the string long enough to hang

now the bottom half of seat what i call the "**** seat" you remove the molding at bottom around the belt retractor this will be bolted to floor bolt also pull belt threw molding once molding removed
disconnect any electric wires

now saftey issue involved with seat belt removal is for a reason i dont know of the dealer ship always discharges the belts and air bags once removed i guess because of static electricity becareful when you remove belt and replacing belts cause static elec. can set them off
once your seat belt is removed place in card board box and take to dealer after complition of installing new belt they will discharge your seat belt for you and then you can dispose of it properly

Posted on May 29, 2008

CMV9
  • 594 Answers

SOURCE: 2004 Chevrolet Silverado Extended Cab

jack the truck up and take the passangers tire off. look behind the rotor you should see 2 bolts holding the caliber on to the rotor. loosen those and take them out. from there you should be able pull up on the caliber this will take the caliber and pads off together. take the pads out of the caliber and install the new ones .

BECAREFUL not to twist or bend the caliber to much or you will bend the brake line.....

once you have installed the new brake pads in the caliber. put the caliber back on the rotor. if they will not fit release the bleader valve to release the pressure. than you should be able to slid the caliber back onto the rotor. once you have done that close the bleader valve. reinstall the 2 bolts to hold the caliber in place. put your tie back one. Follow these steps for the other side.

now once that is done. you might want to blead the front breaks.
what you do is have someone help you. fill the brake resiviour with brake fliud. than start your truck.
Have someone in the cab to press the brake. What you want to do is turn the wheel so you can get to the bleader valve. once you can get to it open it up. have the person in the cab other truck press the brake until you see a steady flow of brake fluid coming out of the caliber. once you see that have the pseron press the brake once more and hold it to the floor.
close the bleader valve.

now do the same thing on the other side. But, make sure you check your resivour fluid first.
This is to make sure you don't have any air in the lines. after you are done with both side put it in gear and hit the brake make sure you stop......... If that works go about half the block down and hit the brake again to make sure you stop......
once you have done that and are comfortable with the way the truck stops than ou are good to go and now know how to change the brakes for future refrence..... be aware the back brakes are diffrent.........

let me know when you are ready for the back brakes.
do not blead the front ones if ou intend to do the back brakes afterwarwords......

if you are only doing the front brakes you must blead the the passanger side first......... if you do not have the bolts holding your caliber on than you will have a pin the you will take a hammer to and knock it out that will release them....

Posted on Aug 01, 2008

  • 3600 Answers

SOURCE: ABS brakes grunt, groan noise with brake pedal travel.

Joe it is common for the brakes to moan when they wear down and sometimes they will squeak, try replacing the front pads and lubing the shafts on the calipers install anti squeal on the back of the pads, the ABS device would not cause noise as they are just a ring with a magnet and the reluctor ring spins and the magnet detects the spinning of the reluctor ring, they don't even touch and are stationary in place where they are mounted. There is a possibility that the brake fluid is dirty and could cause the abs motor to groan but you would just have to flush the system, When you don't put your foot in it on the brakes it will make some noise even new, I have a 2008 ford ranger that makes the same noise and the brakes are fine. You will have to adjust your braking habits to stop the noise. You can change the pads and that will help but not for long, be sure when you are operating your brakes press firmly on the pedal until you stop. If the brakes make noise after you let up on the pedal then the caliper parts need to be cleaned and lubed, however it is not a safety issue.

Posted on Jun 22, 2009

  • 7353 Answers

SOURCE: I have a 2004 Chevrolet Silverado 4x4. Recently I

Is it in 4WD? if it is, take it out.

Posted on Dec 18, 2009

youngenginee
  • 57 Answers

SOURCE: 2004 Aveo Clock Repair/Replace

You will need to remove the dash board of your car.

Posted on Apr 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver side electric seat is stuck in the far forward position and won't move. How do I move it manually or fix the motor.


Auto Repair: How to Replace a Power Seat Motor - YouTube

? 1:44
https://www.youtube.com/watch?v=EDh-0rs5Fjo
Oct 26, 2010 - Uploaded by automdvideos
Auto Repair: How to Replace a Power Seat Motor ... 2007 - 2008 Ford Expedition/Lincoln Navigator Driver Bottom Install Video ...2003-2006 Chevy/GMC Seat Cover Install 1 of 3 - eBay Ready ...2000 Ford Explorer Front Seat Track Stuck Motor Repair - Duration: 4:39. by cubmancan 4,959 views. 4:39.
Drivers seat is dead! No power seat or heat. - TheDieselGarage.comwww.thedieselgarage.com/.../96465-drivers-seat-dead-no-power-seat-hea...Mar 22, 2010 - 2003-2005 Chevrolet Avalanche, Silverado, Suburban, Tahoe 2003-2005.... Power seat on driver side didn't work.....passenger did! Neither ...DANG electric seat ' Chevy Truck Forum ' GM Truck Clubwww.gmtruckclub.com/forum/threads/dang-electric-seat.2990/Apr 27, 2006 - 10 posts - ‎7 authors'03 Tahoe My driver seat just stopped, of corse not where I need it, the ... I have a 2003Tahoe and both heated seats are not working. ... with my seat heater on the drivers seat in my 03 Avalanche, it turns ... The driver's side on my Silverado gets way warmer than the passenger side. ... Frozen New Member.Power Seat Problems?? - Tahoe Forum - Che

Dec 29, 2015 | 2003 Chevrolet Avalanche

1 Answer

Infiniti I35 2004 with all options and 80,000 miles. The driver's electric seat is jammed at the back position and tries to go forward whenever the car starts and all it can do is make a grinding...


sounds like the motor is bad easiest and cheapest way to fix would be to get a complete seat from the Junk yard the seat should come with all the motors and tracks all you have to do is unbolt old seat and bolt down new one only draw back to this is seat might not be same color but there two ways to fix that first u could just get a set of seat covers Or you can take the track and motor off new seat and install them on the old seat

May 11, 2011 | Infiniti I35 Cars & Trucks

1 Answer

Out of the blue my 2006 silverado is blowing hot air on driver side only. why?


if this has a dual zone,driver/pass control then either control or electic servo motor have failed,dealer only parts most of the time,gm tech 2 scanner can help with diagnostics,with key on engine off listen for motor noise as you cycle from hot to cold,if normal rotate without stripped gear noise then could bea stuck blend door.good luck

Aug 08, 2010 | 2004 Chevrolet Silverado 1500 Crew Cab

3 Answers

Power seats wont move forward


it souns like the switch on the seat has stopped working or the motor itself has gone bad I would check the switch first

Aug 01, 2010 | 2006 Nissan Murano

1 Answer

2004 suburban driver 6 way seat will not go up and down but will go forward and backward


there is 2 power seat motors in that seat 1 must have gone out take to repair shop and check voltage of both motors

May 28, 2010 | 2004 Chevrolet Suburban

3 Answers

03 Ford up and down in power seat


Had this same issue with my 2004 Expedition. I removed the seat, seat motor and seat track. I tested the motor by plugging back in but without the track and was spinning freely. Took the track to the Ford Dealer. Was able to speak to a service tech. Said it is not the motor it’s the track, it gets stuck if you move to the extremes of the up or down. It’s like over tightening a jar stuck and unable to open again. WHAT TO DO: there are to impellor rods the spin on both sides of the motor. The rods look like wound up springs. Reconnect the rods back in the track. Use your Electric drill to hold the other end of the to break free the stuck track by spinning the impellor rod. Do this for both side. make sure to align the rods properly before return the motor. Also, try not to fully extend the power seat to the very up or down of the track. This will keep from causing the stuck jar effect. ONE and DONE.. Hope this helps.

Feb 07, 2010 | 2003 Ford Expedition

1 Answer

Bucket seats with driver 1 and 2 memory and also seat warmer oh and the seat warmer does not work ever since.


Hi I'm not to clued up on 2004 silverado 1500 LT crew cab, obviously you'll check the fuse box & even replace the fuse wouldn't hurt giving it a try. Also try checking the electric motor for the seat. No cables lose or broken? Nothing jamming the seat? Is there any sound at all coming from the area where all the electrics are under the seat? Can you hear a motor straining?Just a few thoughts. Good luck

Jun 01, 2009 | 2004 Chevrolet Silverado 2500HD

3 Answers

Driver's seat unable to move forward or backward


There are plastic gears connecting the track to the seat assembly. Whne one of these strip the seat will only work or move to one side. Infiniti does not sell a simple fix. You are looking at buying an entire seat assembly complete with the module for all the electronics. It will be at a cost of around $950 - $1000. Once that is in, Infiniti must program the seat to the brain of the car, only then can you reset your memory settings.

May 19, 2009 | 2004 Infiniti G35 Sport Coupe

1 Answer

2000 alero power seat stuck


this more likely is a worn out gear that spins and moves the seat. you should check the motor to see if it actually spins if it does repair the gear.

Jan 27, 2009 | 2002 Chevrolet Silverado 2500HD

3 Answers

Six way power driver seat bottom does not adjust up or down.


it can only be 2 things, either the switch is bad or the motor in the transmission is bad, both parts are a common failure so u must test each to determine which is at fault, do u have a 12 volt test light? if not get one, about $6 from any parts store like Kragen, Autozone and others, raise the seat as high as possible and disconnect the motor that is inop, (be careful not to break the connector locks) push the switch to operate that motor in one direction (up for this test), the test light should light, then move the test light to the other terminal of the connector and press the switch for down, again the test light should light, if the lights go on as described then the motor is the problem and if they don't the switch is the problem.

Jan 14, 2009 | 2004 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

891 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...