Question about 2002 Dodge Durango

1 Answer

Surpentine belt how much should i pay to have one replaced...2002 dodge durango with 4.7l v-8

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 62 Answers

The labor shouldn't be more than two hours and the part should be around $75.00 max. So moderate shop will charge $95.00/hr for labor, a dealer closer to $125/hr. So at a cheaper repair shop, $265 plus tax, at a dealer more like $325 plus tax. Its an important component, but you don't have to get it fixed at a dealer. hope this helps
P.S. Pep boys has cheaper labor and good mechanics.

Posted on Oct 31, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to add a third row seat to a 2002 durango

Contact u pull u pay or similar junk yard. Get the seat from them. if yours never had a third row, some modifications may be necessarybut there's probably a place to mount the seat. When you pull it, be sure should take the bolts as well... and maybe the seat belt mechanism if it's become separated. Good luck!

Jun 21, 2014 | 2001 Dodge Durango

1 Answer

I have 2002 Durango with 360CID engine. #8 cylinder is not firing.

Could be lack of compression, or too much fuel from the injector.

Mar 02, 2014 | 2002 Dodge Durango

1 Answer

When outside air temperature remains at or below 32 degrees for an extended period, the starter motor on my 2001 Dodge Durango, 4,7L engine, tries to engage without the key being in the ignition as the...

this could be moisture going into the starter motor, and freezes over night, making a shortcut to the starter. My advice, change your starter and your problem should be fixed.

Dec 14, 2010 | Dodge Durango Cars & Trucks

1 Answer

What size is the engine on a 2002 dodge durango R/T? Need to change the surpentine belt.

4.7L or 5.9L and it should be listed on a sticker somewhere in the engine compartment.

Drive Belt Removal & Installation 3.7L, & 4.7L Engines To Remove:

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect negative battery cable.
  3. Rotate tensioner until it stops.
  4. Remove belt and slowly rotate the tensioner back to its free position.
To Install:
  1. Install new belt and route around all pulleys except idler pulley.
  2. Rotate the tensioner arm until it stops.
  3. Route the belt around the idler pulley and slowly let the tensioner rotate back to its free position.
3.9L, 5.2L, & 5.9L Engines To Remove:
NOTE: Check the belt routing label, located in the engine compartment, for the most current belt routing schematic.
Do not attempt to check tension with a belt tension gauge on vehicles equipped with an automatic belt tensioner.
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Attach a socket wrench to the pulley mounting bolt of the automatic belt tensioner and rotate the tensioner assembly clockwise until tension is relieved.
  3. Remove or disconnect the following:
    • Belt from idler pulley
    • Belt from vehicle
To Install:
  1. Position drive belt over all pulleys except idler pulley.
  2. Attach a socket wrench to automatic belt tensioner and rotate the tensioner assembly clockwise.
  3. Install belt over idler pulley, allow tensioner to rotate back into place, and remove the wrench.
prev.gif next.gif

Sep 03, 2010 | 2002 Dodge Durango

1 Answer

How to replace surpentine belt

Unless you have a little experience working on cars this could be tough. There should be a picture of the belt routing somewhere under the hood. The tricky part is the tensioner, it has to be pulled up to get the old belt off and the new one on. It should have a square hole in it, I use a 3/8 drive long handled breaker bar to fit in the hole and pull up on the tensioner.Have patients and good luck.

Oct 12, 2009 | 2005 Pontiac Montana SV6

1 Answer

Surpentine belt.

depends on which v8 you have....the 4.7 the routing is as follows it goes under the waterpump pully over the alternator down and around the power steering pumpto the goes under the bottom of the crank to the idler pully.the flat side of the belt goes ver the idler then around the automatic tensioner to the ac compressor.
on the 5.2 and 5.9 it routes starting at the idler pully the flat side goes undr the idler the up to the ac compressor around the compressor and down to the power steering pump ... around power stering pump to waterpump where the flat side is against waterpump pully around water pump down and around crank up it automatic tensioner....around tensioner and up and over alternator

Nov 30, 2008 | 2000 Dodge Durango

Not finding what you are looking for?
2002 Dodge Durango Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

77947 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides