Question about 2001 Ford Explorer

1 Answer

Heater Blower motor

My heater blower motor only works on the high setting

Posted by on

  • Anonymous Mar 17, 2014

    blower motor won't work

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 107 Answers

Check the plug on resistor block for corrosion. If not corroded replace the resistor block. If it is corroded replace the block and get a new plug at the same time.

Hope this helps.

Mike

Posted on Jan 07, 2009

6 Suggested Answers

  • 51 Answers

SOURCE: Heater Control Switch Only Works on High

I would Replace the blower Resister aka temperature heater fan resister.

Posted on Oct 08, 2008

  • 3 Answers

SOURCE: The heater / ac blower

It is the blower resister. I purchasted one at auto zone for $18.00. It is located under the passenger side dash. You need to remove the glove box and the plastic cover under the dash to expose the blower motor. the blower motor resister is right next to the motor. Simply unplug the resister remove the two screws and replace. I did this and now my fan works on all speeds.

Posted on Sep 17, 2008

emissionwiz
  • 70387 Answers

SOURCE: heater blower motor works intermittently

I would replace the blower motor, this sounds like a motor brush problem inside the motor itself.

Posted on Jan 24, 2009

  • 1 Answer

SOURCE: Fan blower motor

The Canyon has an inherint problem with the Fan Power cable being loose. When I say loose...I'm saying that you need to adjust the wires and then take a zip strip to tighten it up.

Passenger side under the dask are 2 cable hook ups. the one on the farthest right (Only 2 wires going to the plug) is the fan power cable. Jiggle it while the fan is on position number3 so you can hear when it comes on!!!

Posted on Mar 11, 2009

  • 14 Answers

SOURCE: My heater only works on high blower, does this

The switch doesnt need replaced, it is most likely the Resistor for the blower motor. They are common for burning up and only the high speed will work.,

Posted on Feb 25, 2010

Testimonial: "Thanking you ever so much this was the problem"

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater blower only works on high


Most likely the blower motor resistor or the fise for the low speeds. The high setting for the blower motor is on a separate circuit than the other lower settings.

Dec 04, 2013 | 2008 Chevrolet Hhr

1 Answer

My heater blowers dnt work and i need to knw where i can locate the resister blocks for my heater blowers so i can ghange them


Its located under dash,or near glove box.

The dash panel lower side has to be out.

HEATER BLOWER MOTOR


Its faulty blower motor resistor. The low and medium speed on blower motor is controlled by resistor and its actual speed is high. So because resistor is not working, blower motors actual speed which is high is working.


It can be faulty blower motor or faulty blower motor resistor. Get the blower motor inspected. If it's faulty it has to be replaced.


=======

For blower motor testing and replacing, check the link below: ----

Blower motor Testing/replacing for all vehicles?

http://repairhelpcenter.blogspot.in/2012/02/blower-motor-replacing-for-all-vehicles.html

------------

These will help.

Thanks.

Nov 28, 2012 | Cars & Trucks

1 Answer

Heater is not working


HEATER BLOWER MOTOR


Its faulty blower motor resistor. The low and medium speed on blower motor is controlled by resistor and its actual speed is high. So because resistor is not working, blower motors actual speed which is high is working.


It can be faulty blower motor or faulty blower motor resistor. Get the blower motor inspected. If it's faulty it has to be replaced.


=======

For blower motor testing and replacing, check the link below: ----

Blower motor Testing/replacing for all vehicles?

http://repairhelpcenter.blogspot.in/2012/02/blower-motor-replacing-for-all-vehicles.html

------------

These will help.

Thanks.

Nov 28, 2012 | 1988 Honda Accord 4 Door

1 Answer

93 nissan maxima heater blower motor works on high only


You have a defective heater blower resistor, the part is located next to the blower motor in the air ducting that it uses to cool the resistor.

Aug 24, 2012 | Cars & Trucks

2 Answers

Cannot get the heater to work


CHECK SEE IF HEATER BLOWER MOTOR WORKING, REMOVE HEATER BLOWER MOTOR HOT WIRE HEATER BLOWER MOTOR SEE IF BLOWER MOTOR WORKING BLOWER MOTOR FAULTY OR YOU HAVE FAULTY WIRING AT BLOWER MOTOR AND RESISTOR.

Nov 05, 2011 | 1996 Mercury Grand Marquis

1 Answer

Heater does not work


Check heater fuse.
If fuse good - could be a failure of the blower fan motor or blower control switch.
If fuse bad - bad blower fan motor could have blown the fuse.
DO: check fuse, then blower motor.
Pricing: new blower motor: Duralast PM270 $43.99
new heater control switch: Duralast SW229 $46.99 (without
A/C).
I'd expect your blower resistor to be good - when they fail, the blower only will work on HIGH setting.

Oct 23, 2010 | 1993 Dodge Caravan

1 Answer

My Blower motor for my heater on a 99 ford escort is not working.Is it the motor or resister that is gone??the fuses look ok where is the resister located can you send a diagram


look in passenger foot well on blower case for 4 wire connector.



Behind right side of I/P, A/C-heater plenum


resister bad would still allow high speed. may be blower motor.

  • The blower motor does not operate/does not operate correctly
  • Open fuse.
  • Tripped circuit breaker.
  • Circuitry open/shorted.
  • Heater blower motor switch (18578).
  • Heater blower motor switch resistor (18591).
  • Blower motor relay.
  • Blower motor.




bfddb09.gif

Jan 16, 2010 | 1999 Ford Escort

3 Answers

Blower speeds on ac/heater for 2003 chevy pickup(v6)


Hi, sounds like your blower motor resistor needs to be replaced. If not the resistor, check the blower motor.

Jul 27, 2009 | 2008 Dodge Ram Pickup 1500

1 Answer

I have a 2000 ford E350 van with front and rear air. the front blower motor runs at low speed, The front blower still runs on low even when the knob is set on medium or high. I do not know where the...


it's either the blower motor switch or blower motor resister. Resistor ?Heater Blower Motor Switch Removal Remove the battery (10655) ; refer to Section 414-01 . Remove the battery tray. Remove the screws. Remove the battery tray. Disconnect the heater blower motor switch resistor connector. Remove the heater blower motor switch resistor (18591). Remove the two screws. Remove the heater blower motor switch resistor. ----------------------------------- Switches Removal Disconnect the battery ground cable. Remove the center trim panel; refer to Section 501-12 . Remove the control assembly. Remove the screws. Remove the control assembly. Remove the A/C-heater function selector switch knob. Disconnect the vacuum harness connector. Disconnect the A/C-heater function selector switch connector. Remove the A/C-heater function selector switch. Remove the screw. Remove the A/C-heater function selector switch. Remove the temperature control switch knob. Disconnect the temperature control switch connector. Remove the temperature control switch. Remove the screw. Remove the temperature control switch. Remove the heater blower motor switch knob. Disconnect the heater blower motor switch connector. Remove the heater blower motor switch (18578). Remove the screw. Remove the heater blower motor switch. ----------------------------

Mar 31, 2009 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

Blower for heater stopped


Remove the hush panel under the dash and unplug your blower motor turn the knob and see if its getting power. If it is replace the blower motor. If your heater seems to work on high but not the other 4 settings. replace the blower motor resistor and pigtail (same general location as blower motor)

Jan 31, 2009 | 2004 Chevrolet Silverado 2500HD

Not finding what you are looking for?
2001 Ford Explorer Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...