Question about 1997 Ford Contour

1 Answer

Blower fan removal from 97 ford contour

How to remove blower fan from 97 ford contour

Posted by on

  • Anonymous Mar 26, 2014

    I'm trying to replace a fan blower motor for a 1997 ford contour, but I'm not sure how to take the other one off



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 337 Answers

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need to find where the blower fan is located on a 199 ford contour...and what it looks like

the blower fan is usually mounted on the passenger side engine compartment on the firewall. It is mounted on the duct work leading into the car. It is round with usually 2 wires going into it.

Jun 09, 2011 | 1999 Ford Contour

1 Answer

Fan for ac and heater won't come on but can feel warm and cool air

change out the blower motor instructions below
  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Dec 14, 2010 | 2000 Ford F150 Flareside SuperCab

    1 Answer

    How do I remove the heater blower motor on a 1995 ford contour. It has the 2.0 L 4 cyl.

    Blower Motor Switch Resistor Assembly REMOVAL & INSTALLATION Fig. 1: Remove the resistor assembly by gently popping it out of the evaporator housing using a screwdriver 91056g24.gif
    1. Disconnect the negative battery cable.
    2. Remove the push pins and remove the upper footwell panel from under the passenger side of the instrument panel.
    3. Unplug the connector from the blower motor resistor assembly.
    4. Insert a screwdriver approximately 0.2 inch (5mm) under the edge of the resistor assembly to disengage it from the evaporator housing.
    5. Remove the resistor assembly. To install:
    6. Position the resistor assembly into the housing and snap it into place.
    7. Attach the resistor connector.
    8. Install the upper footwell panel.
    9. Connect the negative battery cable. prev.gif next.gif

    Jul 31, 2010 | 1995 Ford Contour

    1 Answer

    Heater of my 1999 ford contour is not working. is there a fuse i can replace to make it work?

    There is a fuse under the steering wheel area, also there is a heater conrol under the passenger side dash on the left side of the blower motor. 1 screw holds it in the plenum(heating duct) there is a 4 wire plug going to it. You can check the actual blower motor for operation by putting 12 volts to it. To remove it there are two tabs on either side of the housing.Remove the wire first. Push the tabs up together and turn the fan housing to remove it. You now will have the whole fan in your hands. Using a wire jump from a 12v source(car battery works) to test the fan.2 wires reqd for + and-. if the fan does not function it may need replacing or just lubrication.

    Jan 09, 2010 | 1999 Ford Contour

    1 Answer

    Radiator cooling fan unit

    it comes out the bottom with the radiator

    Jun 25, 2009 | 1997 Ford Contour

    1 Answer

    96 ford contour blower fan removal

    You remove the heater blower by removing the bottom cover of the Glove Compartment. Then you will see The heater blower housing. Then you will see like a black clip you need to lift. Then You simply turn clockwise and bingo its off. To install just do the same thing except in reverse mode. Good Luck!!

    Oct 28, 2008 | 1996 Ford Contour

    1 Answer

    Fan motor

    cooling fan or blower motor?

    Aug 02, 2008 | 1998 Ford Contour

    2 Answers

    Blower fan

    How do you remove the blower fan

    Aug 01, 2008 | 1997 Ford Contour

    Not finding what you are looking for?
    1997 Ford Contour Logo

    Related Topics:

    574 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts


    Level 3 Expert

    77499 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers


    Level 3 Expert

    5622 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides