We have a 1991 Civic DX and the rear wiper stopped working about 2 weeks ago after I changed the blade. The front ones work fine. Any suggestions on where to start troubleshooting and repair this issue?
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
? 4:54 www.youtube.com/watch?v=P3TqheRsX1w
Sep 25, 2013 - Uploaded by Honda Civic How To
Hi in this first video i will look at how you can easily change a failed bulb in a 2001-2005 Honda civic's hazard ...
honda-tech.com/honda-civic.../%5Bdiy%5D-92-00-civic-rear-hatch-glas... [DIY] 92-00 Civic REAR Hatch Glass Intermittent Wiper Retrofit Guide ... The answer lies in a 1997 Honda CR-V. So the 98+ CR-V models all had their rear ... Remove the Rear Intermittent Washer/Wiper Relay from the under-side of the dash, ...
These are available at the dealership. There is one way though. You can get a 21" RAIN X wiper and i just cut it down to size. The grooves on a RAIN X will fit up to your rear wiper. As far as replacing it although it looks more difficult at first glance it it every bit as simple as the front wiper blades. It's a simple pop off. You can also just change rubber wiper and leave the actual blade alone. the rear is a mini blade style (this refers to the size of the rubber insert in the blade, not the actual whole blade being small.) You can replace the rubber using an Amcor blade or any "mini" blade. Puchase the biggest one they have, take out the rubber wiper and just cut to size. You can change the rubber many times off of one blade thus saving you a bunch of money.
My wife has a 08 Fox and her front wipers stopped working it's just a fuse in bank 7 a 10 amp just replace with a new one or swap for the 10 amp fuse in bank 11 (just a warning lamp for the handbrake) until you get a new one. ;-)
Raise the rear wiper blade to the position as shown in the
illustration where the meshing of the claw disengages with a clicking
sound. NOTE: Be careful not to break the claw.
Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.
REMOVE REAR WIPER RUBBER
Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middle area of the blade.
INSTALL REAR WIPER RUBBER
Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be careful to observe and keep direction of curvature for correct replacement.
b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
c. After passing the rear wiper rubber through the rear end side claw,
protrude it from the rear end stopper and pass it through the front tip
Very simple solution, indeed, as expected. RainX wiper blades come with a small device designed to replace the snapping mechanism on the existing wiper blade. Once you get the existing mechanism off (which can be a little testy), you snap the new in place and it fits perfectly. Rear blade just requires a little patience. Once you get it off (which can also be a little testy), the new one snaps in place perfectly. Although I was able to solve my own problem, this is a really nice service that you provide, thanks.
1. check the fuse to the rear wiper motor
2. check for power to rear wiper motor at the motor (power wire going in to the wiper motor with rear wiper switch on)
If you have good fuses & have power going in to the rear wiper motor...
3. Pull old rear wiper motor and install a new rear wiper motor.
Thank you please drive thru......
My rear blower motor stopped working and my Brother took the unit apart. He found out that the fan blade had seized up the unit. After he took out blade and sanded down blades, it worked fine. However, I am not sure about your front unit. Good luck.
Your rear bottle for the wipers should be at the back of the vehicle.Look in back for removable panel and bottle should be there.Turn your ignition on(no start)and activate rear washer Listen for the sound of the motor
The 2006 Toyota RAV4 takes a 24" drivers side, 17" passenger side and has a special 17" rear blade. Don't just go by lengths though - when buying windshield wiper blades be sure to always use the application guide book at the store or now-a-days you can Google 'lookup wiper size'.
You want to look this up because correct wiper fit is more than correct length, it's also proper attachement. Not all attachments fit all arms. Using the application guide or looking up wiper size online will avoid headaches of buying the right lengths with the wrong attachements.
The replacement wiper blades will come with step-by-step, illustrated instructions and once you have the instructions and the wiper blades/arms in your hands in front of you, it will all make better sense and will an easy maintenance task. Very simple and takes 5-15 minutes usually not requiring any tools.
If in your budget, upgrade to the newer-style frameless "beam blades" which perform better than conventional framed wipers. I use Trico NeoForm Beam Blades which are fantastic.
Hope this helps!
PS: Your question is about the front blades but if you address the rear blade too, this vehicle has what they call a "Roc Lock 2" rear arm. You can go to your dealer or I know Trico makes an "Exact Fit Rear Integral Blade 12-A". There may be others available too. I've got the Trico on my Jeep and it fits/works great.