Question about 2003 Jaguar X-Type

1 Answer

Replaced battery - need to reset clock / radio won't play

Battery was replaced and now I can't reset the clock... I do not have the touchscreen panel, and the manual says to use the touchscreen??? I can't find any info online... Also, when I press the AM/FM button, it says "No AM" or "No FM"... And the radio does not play...

Posted by on

  • sherrymb Dec 06, 2008

    I called the local dealer and the lady gave me "4654" as the code. I punched it in but didn't work. After two failed try, "Please wait" comes on. The manual says that I will have to wait 30 minutes to re-enter the code. I am not going to try the code again though, because I am 500% sure that I entered it right. I will have to call the dealer again tomorrow and complain.

  • stanbarker Dec 22, 2008

    New battery also and the mode button isn't working to change the clock. Need help. Thanks, SB



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My manual said the same thing. Although I have never had the radio stop working on me even after I changed the battery. To set the clock you hold the mode button, like your changing the bass/ treble. Hold it down then it will show clock flashing. From there I cant remember i think i used the arrows by the number pad to change the time. Hope this works for you.

Posted on Nov 05, 2008


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 776 Answers

SOURCE: replaced battery - need to reset clock / radio won't play

Yes.. your problem is a micomp (micro computer) issue. There is a communication problem between the micomp and the touchscreen. Replace the micomp.

Posted on May 26, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

After an oil change the touchscreen on the navigation/radio/bluetooth is not responsive? How do you fix this issue?

I have no clue what changing the oil would have to do with any of this. However, the problem you are describing sounds a lot like the types of problems that occur with a shorted battery cell. I would take a HARD look at the battery and charging system. If your battery is more than 4 years old, it is time to replace it.

If the battery and/or charging system is the cause, you will also very likely have fault codes stored in several of your computer modules. You will have to clear all of these codes from all modules and force a "clean boot" of your computer network to get everything working properly.

Dec 23, 2011 | 2005 Cadillac STS

1 Answer

Information senor panel, clock and radio reset itself, and/or the radio will not work at all

Could be a number of things.

  • Battery discharged or getting there.
  • Loose ground behind the radio unit itself

Jeeps do weird things when the battery is low. If your battery is 4-5 years old or more, its pretty much time to replace it, even if your engine starts normally.

Check the ground wire behind the radio unit. If its loose, it can cause the radio to shut off randomly and not work at certain times, also can cause the radio to lose memory.

Nov 23, 2009 | 1994 Jeep Grand Cherokee

1 Answer

The battery died and was replaced. After replacing the new battery, the radio and clock on dashboard aren't working. How do I reset?

you need the radio code to reactivate the radio. if you dont have it, the dealer can get it.

Nov 12, 2009 | 1996 Nissan Maxima

1 Answer

No power to cab, no power to start, but clock has power

check fuse block for shorts, melting discoloring,on back side of fuse panel around starter relay. loose connection causes fuse block to over heat will need to be replaced.hope this helps.

Oct 29, 2009 | 1997 Chevrolet S-10 Pickup

7 Answers

The clock in my 2000 RX300 keeps resetting to 1 00 am every time I restart the car

I had similar problem in 2001 rx300. Every morning the clock
will reset to 1:00. Sometime this will happen when I started the engine. The Lexus dealership replaced the car battery. According to the mechanic, The Rx300 are very current sensitive system and even though The existing battery was 3 years old the cold weather made the current go below the allowed limit. That makes the clock reset to 1:00. After replacing the Car battery, the problem when away

Jul 07, 2009 | 1999 Lexus RX 300

1 Answer

Replaced battery - need to reset clock / radio won't play

Yes.. your problem is a micomp (micro computer) issue. There is a communication problem between the micomp and the touchscreen. Replace the micomp.

May 26, 2009 | 1996 Ford Explorer

1 Answer

89 Maxima clock and radio needs to be set

You have a blown fuse for the memory for the radio & the clock.

Sep 12, 2008 | 1989 Nissan Maxima

Not finding what you are looking for?
2003 Jaguar X-Type Logo

723 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

79847 Answers


Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides