Question about Mazda Tribute

1 Answer

I own a 5 sp. 2003 tribute and when i engage the clutch the peddle sticks to the floor and i have to pop it back up by hand.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 958 Answers

The spring that supposed to pull it back could have snap broke. check the spring underneath the pedal.

tnx 4 using fixya,

drcool

Posted on Oct 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HI. The clutch peddle on my citroen C4 1.6 HDI stays on the floorboard when pushed please help.


Check this forum:
http://www.citroenpicasso.org.uk/picasso/index.php/topic/18177-sticking-clutch-pedal/

Sep 21, 2016 | Citroen Cars & Trucks

3 Answers

Clutch peddle doesn't come all the way back


If you have to pull the clutch back then you need to check ;::: first of all is it fluid (master cylinder) hydr, clutch ?? reply

Apr 18, 2014 | 1990 Ford F150

1 Answer

Clutch peddle is low to the floor


Sounds like you need to adjust the linkage or possibly change the cable. You might need to change the clutch and pressure plate but that doesn't seem likely. I would start with the linkage.

Mar 26, 2014 | 1991 Nissan Stanza

1 Answer

Clutch peddle wont go all way to the floor


Clutch fluid level low, bad slave cylinder, bent linkage

Sep 22, 2013 | 2003 Hyundai Tiburon

1 Answer

Clutch gets stuck fully engaged every nown and again


Its probably something in the clutch master cylinder. There is a spring inside the cylinder and another on the pedal to pull it up.
I'm assuming the pedal is not sticking on the floor mat.

Aug 27, 2012 | Cars & Trucks

1 Answer

I own a 1995 Audi 90cs. My clutch peddle started being dead tell half way down then got preshure. Now there is no preshure and the peddle sticks to the floor. There was no slipping in the clutch so I


You need to replace the clutch slave.....Ii recently did mine, after the installation it was stuck too.......the way I fix it was I had a friend pumping the clutch by hand while I bleed it under the car, it took about 15-20 minutes before it got hard again.
Good luck!

Aug 01, 2012 | 1995 Audi 90

2 Answers

Need to bleed clutch to get peddle


try to vacuum bleed the system at the master most hand vacuum kit come with adapters to fit over the master reservoir otherwise the system may need a new master or you may have a leak

Sep 04, 2009 | 1994 Dodge Stealth

2 Answers

2001 nissan maxima clutch problems


check the mechanical leakage at the clutch housing for binding and wear.

Jun 12, 2009 | 2001 Nissan Maxima

1 Answer

2000 cavalier clutch pedle goes to floor when pushed and stays there, clutch not working no pressure


You are going to have to replace the master and slave cylinders for the hydraulic clutch, the seals have failed in the slave, but from past experience they should always been replaced as a pair.

Oct 12, 2008 | 1998 Chevrolet Cavalier

1 Answer

Clutch pedal suddenly goes to the floor, no longer [dis]engaging the clutch


I found that having a wood stick on the clutch pedal down to the floor all night (the other end of the stick held by the seat. oh yeah !!! ) would help to ease shifting for the first hour the next morning, then it would come back stiff and hard to engage in gear.

Aug 07, 2008 | 2007 Mazda B4000

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...