Question about 1991 Toyota MR2

1 Answer

Manual Trans If the car starts to drag on your manual trans, what's the problem? (It goes back to normal after dragging.)

Posted by on

  • yadayada
    yadayada May 11, 2010

    Not sure what you mean by dragging?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

What do you mean by dragging? is it that you feel you are loosing power? if this is the case chances are the clutc assembly needs to be looked into the pressure plate and the friction clutch disk are worn out needs replacement, i would check the flywheel and machine the fly wheel before reinstalling a new clutch assembly

Posted on Nov 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1986 Lincoln Town Car drag shifts 1st to2nd. I just drained refilled trans,new filter and gasket, What would make the 1, 2 shift point go up to about 2500 to 3000 rpm's? it finally shifts then acts ok


I am not familiar with your specific car. However I would suggest checking the fluid level of the trans. If you do not have one get an owners manual or repair manual and make sure you are performing the check correctly. Some transmissions require a hot check, some require that you cycle through the gears just before checking, things like that. If there are special instructions you are not following you may not have refilled the trans to the proper level.

May 18, 2015 | 1986 Lincoln Town Car

1 Answer

1996 gmc jimmy will not shift to 3rd gear


Hi, It may be in LIMP mode.

What is "limp-home mode" ? This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Common failures on 4L60E, symptom any possible repair:

Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under-hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter :ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Trans seems noisy when moving in 1st and Reverse, noise goes away instantly if you shift to N or the trans goes into 3rd gear: Reaction planetary is worn out due to high miles or insufficient lubrication. Not a critical failure, but not a good sign either. R&R sooner rather than later.

3rd gear starts, can manually shift through all gears. When car has been turned off for a bit, then back on it will run normally.: VSS dropoff w/ Hi-stall converter. The rpms are too high, but VSS is showing no movement. Happens after a tire burning take-off. Doesn't store a code, will not throw a CEL (I've heard that it will store a code if it happens 3 or more times). Cure: Reprogram PCM for VSS dropoff -- PCMforLess knows about it.

If you can get the Jimmy for no more then $500.00 and the engine sounds good and body is good, you may want to invest in the repair of the jimmy. Also note that to have a close look at the fuel line along the frame on the drivers side just by the back doors, the line is know to corroded there on all the SUV's

Sep 19, 2010 | 1996 GMC Jimmy

1 Answer

Transmission is shifting hard and slow to pull on a 95 silouette also makes clucking sounds while accelerating


Shift suddenly become very hard. When going from park to either reverse or drive it slams into gear. 1-2 and 2-3 shifts are also harsh. All gears seems to work. Problem may be intermittent: Check TPS for smooth and linear electrical response over the entire range of motion. If not, replace.

Extremely harsh shifts from P or N, normal shifts at WOT: EPC (Electronic Pressure Control) solenoid failed. Easy fix in pan. Fix as soon as possible or hard parts will eventually break.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.


Mar 05, 2010 | 2002 Oldsmobile Silhouette

1 Answer

My GMC has 311632 miles on it. I just changed the 4L60E transmission a few months ago and now it wont shift out of first unless I manually put it in second gear. all the gears from park rev. nuetral works...


The transmission may be in Limp mode. The transmission is on the same fuse as the MAF, O2 sensors and at least one other sensor - if an O2 shorts out, it will blow the fuse and the trans will go into limp-home mode. Be sure the trans has power and the fuse is not blown before doing anything else.

What is "limp-home mode" ? This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Trans does not upshift out of first, speedometer reads zero at all times: VSS failure. Easy fix on rear of transmission, but xmember must come out to access VSS.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Transmission does not shift automatically, only manually. Swap in a known-good PCM, check wiring, check other sensors such as VSS and TPS.

3rd gear starts, can manually shift through all gears. When car has been turned off for a bit, then back on it will run normally.: VSS dropoff w/ Hi-stall converter. The rpms are too high, but VSS is showing no movement. Happens after a tire burning take-off. Doesn't store a code, will not throw a CEL (I've heard that it will store a code if it happens 3 or more times). Cure: Reprogram PCM for VSS dropoff -- PCMforLess knows about it.

Here are just some of the common things you have described with the issues your transmission has. Good luck and keep me posted.

Dec 22, 2009 | 1994 GMC Sierra

1 Answer

Only runs in 1st and 2nd gear and reverse.


This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

Trans shifts into gear harshly, car feels sluggish off the line
, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Dec 14, 2009 | 2006 Hummer H3

2 Answers

Hard shifting 1st to 2nd gear. And 4th gear wants to pop out have to hold in with shifter. 1991 Jeep Wrangler. Worse when cold.


Sounds like the trans needs to be rebuilt as it's been abused. The clutch may be dragging during shifts and not completly disingaging or a lasy driver does'nt pust the clutch in all the way. If the clutch isn't the problem the oil in the trans should be ATF and if someone put in 80-90 it'll do this but jumping out of high and the shifter isnt itting the floorboard as a bad trans mount or motor mount may let happen, The trans is damaged and a used unit is cheaper and quicker to get done. Rebuilding the trans with all the parts it may need cost more than your truck is worth

Dec 05, 2009 | 1991 Jeep Wrangler

2 Answers

1996 gmc jimmy won`t shift from 1st to 2nd


IF the abs dash light is on and if the speedometer is sluggish or not working at all, it is probably a bad speed sensor on the transmission. and easy fix under $40 for the part. Mine was stuck in second gear for a while then worked then it stuck in first gear and i had the CHECK ENGINE light on.

Dec 03, 2009 | 1996 GMC Jimmy

1 Answer

Its 2 wheel drive, but the transmission won't shift unless you manuallyl put the gear shifter in low then work your way up to get the gears to change. The gears work fine it just won't change on its on. If...


Trans shifts into gear harshly, car feels sluggish off the line, No 1st, 4th or TCC lockup available, Manual 2nd, 3rd and Reverse are only available gears, CEL is on: Transmission is either in limp-home mode or has lost electrical power. If there are lots of error codes in the PCM, check the under-hood fuse that powers the transmission, and if it pops again, look for a short in that circuit like an O2 sensor harness touching exhaust. Otherwise, check PCM codes for a particular fault in the transmission causing the PCM to put it in limp-home mode.

No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Car goes into gear but feels very sluggish like the brakes are dragging, but it will roll easily (starts out in 4th gear), you manually shift to 2 to get it moving, once it's moving you put it back in OD and the car shifts 3rd to 4th on its own and locks the converter at the appropriate time: ShiftB solenoid failed: Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Good luck and keep me posted, there are other things but these things mentioned seam like what you described.

Nov 19, 2009 | 1993 Isuzu Rodeo

1 Answer

Trans will not shift good on take off drags


Make sure your drag link is adjusted correctly, loosin the bolt and let it kind of slip into it's own position.

This should make it shift correctly, and as an extra measure, put a bottle of lucas trans fix in it....

Nov 21, 2008 | 1996 Chevrolet Blazer

1 Answer

Brake Fluid and Manual Trans


Brake fluid tends to attract humidity from the atmosphere it must be renewed every 2 years or 20000kms.
I would check the tyres and tyre pressure as well.

Oct 29, 2008 | 1991 Toyota MR2

Not finding what you are looking for?
1991 Toyota MR2 Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...