Question about 2000 Ford Focus

2 Answers

2000 ford focus stall/loss of power while driving

The car (sometimes) has a loss of power and will not rev. over 2000rpm

Posted by on

  • Anonymous Jan 05, 2009

    2.0 zetec random loss of power after driving for like 30 mins taken to many mechs. replaced many parts no fix

  • Anonymous Mar 27, 2014

    WHEN DRIVING , LOSSES POWER WHEN ACCELERATINGAND STUTTERS .HAVE TO CHANGE DOWN IN GEARS TO GET REVS UP

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

I ran into this with my focus. It turned out to be a loose connection on the crank sensor. It started right after i changed the serpentine.

Posted on Jan 26, 2009

  • Sukumaran Gandy
    Sukumaran Gandy Mar 17, 2013

    in the case of my ford focus, usually in the morning after the engine idles to about 60 degrees temperature i move off

  • Sukumaran Gandy
    Sukumaran Gandy Mar 17, 2013

    but this happens only when moving off just above idling speed, and as apply my service brake while I exit from the multistorey carpark and is it common for the rpm to keep moving between 1000 rpm to 950. please advise

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Expert
  • 611 Answers

Transmission shift solenoid can cause it feels like engine is bog down

Posted on Oct 29, 2008

  • Sukumaran Gandy
    Sukumaran Gandy Mar 17, 2013

    but this happens only when moving off just above idling speed, and as apply my service brake while I exit from the multistorey carpark and is it common for the rpm to keep moving between 1000 rpm to 950. please advise

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ivg got a 2005 Nissan Almera Tino 1800 petrol Ive got a problem still, I cant find an OBD reader that works with it,


check fuses and relays --check for power[ fuse ] to the port on quit a few vehicles usually the accessory fuse and obdll port are same ==the following link shows what pins to check with a meter if you have power to the port then start checking your harness,connections and computers
OBDII On Board Diagnostic System Does My Car Have OBD II The Connector...

Sep 11, 2016 | 2005 Nissan Almera Tino

1 Answer

Stalling and bucking above 2000rpm


Sounds like an ignition misfire. Is the check engine light on ?

Jul 31, 2015 | 2001 Nissan Quest

2 Answers

My problem comes and goes. the eng light comes on, I go above 60mph it bucks til I drop to 60 or lower I stop at a light it wants to stall. I leave the light it drags n revs up to 2000rpm no higher.


Your having spark leak to the block check wires and boots look for cracks or burns and anti freeze could be leaking down into the cylinders causing the +to jump to - then the computers freaking out because the codes are affecting thr trans/emissions and extreme loss of power and engine management is the result

Mar 31, 2015 | Cars & Trucks

1 Answer

Engine wont rev above 2000rpm


If you have a hih miles truck,it is very possoble you have aclogged cat.Have a muffler shop test pressure in front and behind by drilling small holes,checkin w/gauge,then welding back.This should be free if you replace the cat.

Mar 23, 2014 | 2002 Ford Expedition

2 Answers

2000 ford expedition I changed plugs pcv egr valve cover gasket I am still getting power loss and hesitation in drive and sometimes it stalls plus I have a b1676 code


There is no B1676 DTC. You probably mean P1676 which refers to incompatible injector data. Probable causes are:
1. Control unit software needs updating
2. Faulty PCM or ECM

Checking these two probable causes may get performance back to normal.

Jan 16, 2014 | Cars & Trucks

1 Answer

With the TPS connected, it won't go pass 2000rpm.


different airflow meter calibrations,do you have the z32 airflow meter installed?

Oct 31, 2017 | Nissan 300ZX Cars & Trucks

2 Answers

Speedo


you need to change your speedo cable if it isnt electric if it is check for faulty vehicle speed sensor

Jun 12, 2010 | 2000 Ford Focus

Not finding what you are looking for?
2000 Ford Focus Logo

1,084 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5608 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...