Question about 1999 Dodge Durango

1 Answer

Removing '99 Durango starter

I have removed bolt & nut on starter, but it seems to be frozen on. Suggestions? '99 Durango 5.2 Magnum 4wd

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Make sure you have all of the bolts off. Sometimes they hide one really well. Then just tap lightly on the starter case to free it up.

Posted on Nov 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you pull the starter from a 99 dodge durango?


Disconnect battery.
Find positive battery wire and follow it to lower side of engine to the starter.
Disconnect battery wire from starter.
Loosen & remove the (usually 2) retaining bolts holding starter to engine.
Remove starter with a back and down action.

To replace just do the opposite.

Hope this helps...

Jul 23, 2011 | 1999 Dodge Durango

1 Answer

I need to replace the starter on my 1998 Dodge Ram 1500 4wd 5.9l


Easy fix my friend.

1. Unhook the battery
2. Raise and support the truck on jack stands.
3. The starter is located on the drivers side at the front of the tranny.
4. Grab an 8mm and a 13mm wrench.
5. Remove the power wires from the starter.
6. Remove the starter by removing the top bolt 9/16 i believe and the bottom nut. Also 9/16 or 5/8.
7. Carefully slide it out toward the front of the engine.
8. Installation is the same as removal.

Hope this helps.

May 09, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer

How do I change a starter in a 1989 5.2 liter dodge ram truck?


REMOVAL & INSTALLATION
Gasoline Engines



88dac70.jpg


Fig. 13: Disconnect the wires attached to the starter solenoid to facilitate removal
  1. Disconnect the negative battery cable.
6c5429b.jpg

Fig. 14: Unbolt the starter from the vehicle

  1. Remove the cable from the starter.

38a579f.jpg
Fig. 15: Once detached, remove the starter from the vehicle


04789a9.jpg
Fig. 16: Exploded view of the starter mounting-2.5L engine
  1. Disconnect the solenoid leads at their solenoid terminals. If necessary, tag then to avoid confusion when re-installing.
9796cc6.jpg
Fig. 17: Attach the starter wire connector to the terminals as shown-V6 and V8 engines


2e59350.jpg
Fig. 18: To remove the starter, unbolt the mounting hardware shown-V6 and V8 engines


On 4WD Dakota models with the V6 engine, the starter is removed from above. On these models you will have to disconnect the steering gear and position the shaft out of the way to gain working clearance.
  1. Remove the starter attachment bolts and withdraw the starter from the engine flywheel housing. On some models with automatic transmissions, the oil cooler tube bracket will interfere with the starter removal. In this case, remove the starter attachment bolts, slide the cooler tube bracket off the stud, and then withdraw the starter.
dc7317b.jpg
Fig. 19: When detached, pull the starter away from the engine and remove it from the vehicle-2WD Dakota model shown

To install:

  1. Be sure that the starter and flywheel housing mating surfaces are free of dirt and oil to make a good electrical contact.
1547e44.jpg
Fig. 20: Install the starter motor on the 4WD Dakota from above as shown
  1. Slide the starter in place, secure using the bolts and washers removed. Tighten the bolts to 50 ft. lbs. (68 Nm). Connect wires and battery cable end at the starter.
  2. If removed for clearance, reconnect the steering column shaft.
  3. Secure the oil cooler bracket if equipped. Connect the negative battery cable on the battery.
When tightening the mounting bolt and nut on the starter, hold the starter away from the engine for the correct alignment.

Diesel Engines

  1. Disconnect the negative battery cable.
  2. Raise the truck and support it safely on jackstands.
  3. Disconnect and label the wires at the starter motor.
  4. Remove the attaching bolt, nut and washer, then lift the starter and solenoid assembly from the engine.
To install:
  1. Before installing the starter motor, be sure the mounting surface on the drive end housing and the flywheel housing are clean, to ensure good electrical contact.
  2. When tightening the attaching bolt and nut, hold the starter away from the engine to ensure the proper alignment. Tighten the bolts to 32 ft. lbs. (43 Nm).
  3. Attach the wiring at the starter. Tighten the solenoid connection to 44 inch lbs. (5 Nm). Tighten the battery cable at the starter motor to 16 ft. lbs. (22 Nm).
  4. Attach the negative battery cable.
SOLENOID REPLACEMENT
Chrysler Corp. for 1989-91 models did provide replaceable solenoids for the starter motors covered by this information. However since 1992, the manufacturer no longer recommends replacement of individual components, even if the later unit has the same part number of a formerly serviceable unit. Chrysler now simply calls for replacement of the entire starter assembly if the solenoid is found faulty.

e1aa751.jpg
Fig. 21: Starter electrical connections and mounting bolt locations-diesel engine


Hope helped with this (remember rated this post) Good luck.

Mar 05, 2010 | 1989 Dodge Ramcharger

2 Answers

How do I remove and replace a starter from a 1993 Toyota Previa? I am told it's rather difficult and may include removing something from the automatic transmission.


Removal & Installation
  1. Disconnect the negative battery cable from the battery.
  2. Raise and safely support the vehicle.
  3. If equipped with 4WD, remove the front drive shaft.
  4. Remove the nut and disconnect the starter wire.
  5. Disconnect the starter connector.
  6. Remove the bolt holding the starter stay to the upper stiffener plate.
  7. If equipped with 2WD, remove the starter by removing the nut and three bolts.
  8. If equipped with 4WD, remove the starter by removing the nut, four bolts, and the center bracket.
To install:
  1. If equipped with 4WD, install the starter, the center support bracket, nut, and the four bolts.
  2. If equipped with 2WD, install the starter, nut and three bolts.
  3. Install the bolt to hold the starter stay to the upper stiffener plate. Tighten the bolt to 43 inch lbs. (5 Nm).
  4. Install the starter connector.
  5. Connect the starter wire with the nut. Tighten the nut to 78 inch lbs. (9 Nm).
  6. If equipped with 4WD, install the front drive shaft.
  7. Connect the negative battery cable.
Good luck and this should take about 2 1/5 hours from start to finish and if you like, use lock tight medium strength to make sure the bolts don't go lose on you.

Nov 04, 2009 | 1991 Toyota Previa

1 Answer

I need a left front door/window schematic on line for a 99 Dodge Durango. I need to see how to put it together.


Front Door
  1. Remove the door trim panel.
  2. Remove the water dam.
  3. Remove the inner and outer door belt weatherstrips.
  4. Lower the window to the full down position and align the glass regulator arm with the access holes in the inner door panel.
  5. Remove the front glass run channel.
  6. Remove the nuts attaching the glass channel to regulator arm.
  7. Separate the glass and lift it up and out.
  8. Disengage the power window motor wire connector from the door harness, if equipped.
  9. Loosen the bolts in slotted holes attaching regulator to door inner panel.
  10. Remove the bolts attaching window regulator to inner door panel.
  11. Remove the regulator through the access hole in the inner door panel.
  12. Installation is the reverse of removal. Tighten the nuts attaching the glass to the lift plate to 7 ft. lbs. (9 Nm).
3455a81.gif
Power window regulator mounting—Dakota, Durango

6125789.gif
Window regulator removal—Dakota, Durango

Posting more on next post for door panel removal and installation.

Oct 26, 2009 | 1999 Dodge Durango

1 Answer

How to change starter on 2000 chevy silverado


These instructions are for a 5.3L. Unless it is a V6 or diesel, the instructions will be similar if you have a different gas V8.
  1. Disconnect the negative battery cable
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  3. Remove the protective shields as necessary.
  4. Remove the starter solenoid shield.
  5. Remove the starter to transmission close out cover bolt.
  6. Disconnect the engine oil level sensor connection.
  7. Remove the front axle mounting bracket through bolt nut, if equipped with four wheel drive (4WD).
  8. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt, if equipped with 4WD.
  9. Remove the mounting bolts from the engine block.
  10. Slide the starter forward until the starter clears the transmission.
  11. Remove the starter transmission close out cover
    1. Disconnect the positive battery cable and wiring harness from the starter.
    2. Remove the starter from the vehicle.
      1. Connect the positive battery cable to the starter. Tighten Tighten the nut to 16 N.m (12 lb in) .
      2. Install the starter transmission close out cover.
        1. Install the mounting bolts to the engine block. Tighten Tighten the bolts to 50 N.m (37 lb ft) .
        2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated. if equipped with 4WD.
        3. Install the front axle mounting bracket through bolt nut, if equipped with 4WD. Tighten Tighten the nut to 90 N.m (67 lb ft) .
        4. Disconnect the engine oil level sensor connection.
        5. Install the starter to transmission close out cover bolt.
        6. Install the starter solenoid shield.
        7. Install the protective shields as necessary.
        8. Remove the safety stands.
        9. Lower the vehicle.
        10. Connect the negative battery cable. Tighten Tighten the bolts to 17 N.m (13 lb ft) .

Oct 01, 2009 | 2002 Chevrolet Silverado

3 Answers

How do i change the oil pump on a 99 dodge durango


disconnect battery.I believe you have to remove bolts from motor mounts,you will have to remove oil pan. you will also have to lift the motor enough to remove it.there should 2 to 4 bolts that actually hold it on.

Aug 09, 2009 | 1999 Dodge Durango

1 Answer

Starter replacement - 1991 Toyota previa


Here are detailed, step-by-step instructions for the removal and re-installation of your starter motor. Hope this helps! Have a great day!

Starter Toyota Previa 1991-1997 Repair InformationREMOVAL & INSTALLATION
See Figures 5 through 12
  1. Disconnect the negative battery cable from the battery.
  2. Raise and safely support the vehicle.
  3. If equipped with 4WD, remove the front driveshaft.
  4. Remove the nut and disconnect the starter wire.
0900c15280089fbb.jpgFig. 5: Disengage the starter wiring
  1. Disconnect the starter connector.
0900c15280089fbc.jpgFig. 6: Remove the cap hiding the nut 0900c15280089fbd.jpgFig. 7: It will be necessary to use an extension to remove the nut
  1. Remove the bolt holding the starter stay to the upper stiffener plate.
  2. If equipped with 2WD, remove the starter by removing the nut and three bolts.
  3. If equipped with 4WD, remove the starter by removing the nut, four bolts, and the center bracket.
0900c15280089fbe.jpgFig. 8: Four bolts hold the starter in place 0900c15280089fbf.jpgFig. 9: The nut is located on the top of the starter 0900c15280089fc0.jpgFig. 10: Extract the starter from the engineTo install:
  1. If equipped with 4WD, install the starter, the center support bracket, nut, and the four bolts. Tighten the bolts as follows:
    • Bolt A to 41 ft. lbs. (56 Nm)
    • Bolt B to 30 ft. lbs. (41 Nm)
0900c15280089fc1.jpgFig. 11: Bolt locations on the 2WD models
  1. If equipped with 2WD, install the starter, nut and three bolts. Tighten the bolts as follows:
    • Bolt A to 41 ft. lbs. (56 Nm)
    • Bolt B to 30 ft. lbs. (41 Nm)
0900c15280089fc2.jpgFig. 12: Bolt locations on the 4WD models
  1. Install the bolt to hold the starter stay to the upper stiffener plate. Tighten the bolt to 43 inch lbs. (5 Nm).
  2. Install the starter connector.
  3. Connect the starter wire with the nut. Tighten the nut to 78 inch lbs. (9 Nm).
  4. If equipped with 4WD, install the front driveshaft.
  5. Connect the negative battery cable.
SOLENOID REPLACEMENT
The starter solenoid (magnetic switch) is an integral part of the starter assembly.
  1. Remove the starter from the van. Remove the heat insulator from the starter assembly, if equipped.
  2. Disconnect the wire lead from the magnetic switch terminal.
  3. Remove the two long, through bolts holding the field frame to the magnetic switch. Pull out the field frame with the armature from the magnetic switch.
  4. Toseparate the starter housing from the magnetic switch assembly, remove the two screws and the starter housing with the pinion gear (1.6 kW), idler and clutch assembly.
To install:
  1. If necessary, install the gears and clutch assembly to the starter housing. Apply grease to the gear and clutch assemblies and place the clutch assembly, idler gear, bearing and pinion gear (1.6 kW) in the starter housing.
  2. Insert the spring into the clutch shaft hole and place the starter housing onto the magnetic switch. Install the two screws.
  3. Install the field frame with the armature onto the magnetic switch assembly and install the two through bolts. Tighten the bolts on the 1.4 kW to 52 inch lbs. (6 Nm) and on the 1.6 kW to 82 inch lbs. (9 Nm).
There is a protrusion or tab on each part; make sure you line them up correctly during assembly.
  1. Connect the wire to the terminal on the magnetic switch and tighten the nut to 52 inch lbs. (6 Nm). Install the heat insulator, if equipped.
  2. Reinstall the starter on the vehicle. Check starter system for proper operation.

Nov 23, 2008 | 1991 Toyota Previa

2 Answers

Changing the starter on my 99 tahoe


Starter Escalade, Suburban, Tahoe, Yukon, Denali, Denali XL, Yukon XL, 1999 – 2005 REMOVAL&INSTALLATION
Removal & Installation
4.8L, 5.3L And 6.0L Engines
CAUTION Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. Remove or disconnect the following:
    • Protective shields, as necessary
    • Starter solenoid shield
    • Starter-to-transmission close out cover bolt
    • Engine oil level sensor connection
    • On 4WD, front axle mounting bracket through bolt nut
  4. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Mounting bolts from the engine block. Slide the starter forward until the starter clears the transmission.
    • Starter transmission close out cover
    • Positive battery cable and wiring harness from the starter
    • Starter from the vehicle 0900c152800a6916.jpgStarter removal—4.8L, 5.3L and 6.0L engines
To install:
  1. Install or connect the following:
    • Starter
    • Positive battery cable to the starter. Tighten the nut to 12 ft. lbs. (16 Nm).
    • Starter transmission close out cover
    • Mounting bolts to the engine block and tighten to 37 ft. lbs. (50 Nm)
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Engine oil level sensor connection
    • Starter-to-transmission close out cover bolt
    • Starter solenoid shield
    • Protective shields as necessary
  3. Remove the safety stands.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
5.7L And 7.4L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Mounting bolts and shims
    • Wires
    • Heat shield
    • Starter
To install:
  1. Install or connect the following:
    • Starter
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Heat shield. Torque the bolts to 53 inch lbs. (6 Nm) and the nuts to 35 inch lbs. (3 Nm).
    • Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm).
    • Negative battery cable
6.5L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cables
    • Mounting bolts/nuts and shim, if used
    • Starter
    • Wires
    • Heat shield and bracket 0900c152800a6917.jpgExploded view of the starter motor—6.5L engine
To install:
  1. Install or connect the following:
    • Heat shield and bracket. Torque the bolts to 13 ft lbs. (17 Nm).
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Starter
    • Mounting bolts/nuts and shim, if used. Torque the bolts to 33 ft lbs. (45 Nm) and the nut to 75 inch lbs. (8.5 Nm).
    • Negative battery cables
8.1L Engine
  1. Remove or disconnect the following:
    • Negative battery cable
    • On 4WD, front axle mounting bracket through bolt nut
  2. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Positive battery cable nut
    • Positive cable from the solenoid
    • Engine harness ground nut and ground from the solenoid
    • Mounting bolts and starter
    • Heat shield bolts, nut and shield, if necessary
To install:
  1. Install or connect the following:
    • Heat shield, bolts and nut if removed. Tighten the bolts to 35 inch lbs. (3 Nm) and the nut to 44 inch lbs. (5 Nm).
    • Starter and bolts. Tighten to 37 ft. lbs. (50 Nm).
    • Ground wire and nut. Tighten to 30 inch lbs. (3.4 Nm).
    • Positive cable and nut. Tighten to 80 inch lbs. (9 Nm).
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Negative battery cable

Sep 28, 2008 | 1999 Chevrolet Tahoe

Not finding what you are looking for?
1999 Dodge Durango Logo

Related Topics:

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...