Question about 2004 Lincoln Town Car
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Disconnect the battery ground first
1. remove the trim strip from the left and right of the steering assembly
2. take the 12 screws that hold the dash panel
3. take a right angle tool and remove the headlight switch knob by inserting in slot at the back of the knob and pulling toward you and pulling the knob off , this will let you pull back the dash panel and expose the switch. Un- fasten the headlight switch bracket and un fasten the connector and inspect . Replace the switch if necessary , especially if it is burned. GOOD Luck
Posted on Jan 22, 2009
I will make an assumption here, we know what the root word means. This code was extracted from the computer by? What this is telling you one of 2 things: The Bank 2 oxygen sensor down stream of the catalytic converter (there are 2 converters, one for each bank of cylinders on the 4.6ltr engine) is bad and/or that the Bank 2 catalytic converter is no longer doing the job it was designed to do. Simply, Catalysts wear out. They are good for approx 100,000 miles (as required by Federal Law). Again, I assume that the reason the intake manifold was replaced was because it had a crack in one, or more, of the runners? (part that feeds the head of a manifold). It may have taken a while to find this as being the cause of why the car running incorrectly, maybe rough. This means, that during the time the car was being driven with the problem, the amount of unburned, or not within spec exhaust gases, coming off the side of the engine affected by the intake issue was higher than normal. This out of balance level of exhaust gases were being dumped into the converter on that side of the engine, thus causing the converter to have to run hotter, work harder, or even at the time the gas was being processed through, causing deposits to be formed in the converter, thus shortening it's life span. The Bank 1 side of the engine, apparently, did not have the issue and it's catalytic converter's life was not affected. I hope this makes sense to you.
Posted on Aug 19, 2009
Open the hood. Remove the black plastic grill assssembly ( Laying horizontal between the radiator and front bumper). There will be a couple of plastic screws (or some other fastening system) for this part remove and set aside. There is another black plastic grill assembly standing vertical. Remove similar fastening devices and set aside. IF DURING THIS ENTIRE PROCESS there is ANY part that does not come off freely after removing a fastening device (plastic screw, metal screws, hex bolts, bolts) LOOK FOR A PLASTIC CLIP - unclip that as a final step in each of these processes. To continue, Each headlight is attached by three hex or phillips screws.- Remove them and set asside. There is a major clip attaching the headlight at the top. Unattach this and gently remove the entire light housing. The housing will be the unit containing all parts high beam, low beams, side lights, and blinkers. It is a nice tidy unit. To continue, look for a black plastic removable panel on the back allowing access to the back of the bulbs. Remove the 5 screws and set asside. You now have access to the bulbs. The bulbs are attached by a solid plastic clip. Grab the back of the plastic bulb housing and turn about a half of an inch to remove the bulb. Unattach the clip from the wirering harness and you will have the bulb removed. CAREFULLY remove the new bulb making sure not to touch the glass portion of the bulb with hands directly. Skin oils or other debris is not recommended to get on the bulb. Deliberately refasten the bulb wiring harness and replace to the back of the reflection housing. Reassemble all devices. Rinse wash repeat for the other side :)
This seems complex for the task at hand and it is. But from the perspective of repairing a front end after a minor collision is is wonderful. Enjoy...
Posted on Dec 09, 2010
Tips for a great answer:
May 12, 2017 | Lincoln Cars & Trucks
Jun 13, 2015 | 2004 Lincoln Town Car
Feb 15, 2015 | 1993 Lincoln Town Car
Jan 31, 2015 | 2006 Lincoln Town Car
Aug 24, 2014 | 1996 Lincoln Town Car
Dec 04, 2012 | 1993 Lincoln Town Car
Sep 29, 2012 | 1994 Lincoln Town Car
---------Headlight wiring diagram for 1997 Lincoln Town Car?http://technoanswers.blogspot.in/2012/02/headlight-wiring-diagram-for-1997.html
----------This will help.Thanks.
Feb 13, 2012 | 1997 Lincoln Town Car
Jun 04, 2010 | 1986 Lincoln Town Car
93 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: