Question about Dodge Dakota
This truck has run fine now it wont start new (coil 2 times) fule pump, dist looks fine thank you for any info
What about the fuel filter? its usually located under the brake booster where you put the brake fluid in its either under or around that erea somtimes the fuel filter will be clogged also check to see if its getting spark usually you can take the plug out they have a tester for this that you can buy at autozone or checkers or oriellys auto parts store and make sure your getting spark if not it could be bad distributor or cap and rotor check the cap to make sure all the points are there should be 4 or 6 make sure not broken also check the rotar for breakage or rust if its good and is getting spark possible fuel problem with the filter plugged up or possible fuel rail plugged or if you just recently tuned up maybe you have the wrong fireing order need to get a diagram of the spark plug wires if this is all good possible timing belt broke check to make sure the timing belt is good probably do this first so you dont ruin the engine if it is broke
Posted on Feb 25, 2012
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 1990 jeep wrangler
Check the MAP sensor. To see if this is the problem, assuming that the Jeep won't start but is turning over, unplug the MAP sensor and then plug it back in. If you can start it now, the MAP sensor needs to be replaced. The MAP sensor is located in the engine compartment, where the firewall meets the body at the top of the engine compartment, on the driver's side.
Posted on Jul 30, 2008
firstname.lastname@example.org fuel pump is located in the gas tank pop the hood to right of carb or left side look for a black cap that looks like a tire cap it will be on a metal pipe fuel pipe take it of have somebody try to start truck then push the little valve if gas comes out the pump is working if not fuel pump coil i think is mounted left side of motor as you look at it pull coil plug then take some rubber coated needle nose pliers hold near the coil look for blue ark remember this do not hold coil wire with bare hands or bare pliers it will shock you real good my buddy had just a bad coil wire so he got a whole wire set frm autozone they also have a web site autozone,com that will have trouble shooting for your truck let me no what happens
Posted on Feb 21, 2009
I HAVE A QUESTION THAT MIGHT HELP, THE 22-RE 4 CYLINDER HAS A STEEL TIMING CHAIN, IVE BEEN TOLD THAT THE V-6 HAS A RUBBER TIMING BELT ON THE SIDE OF THE MOTOR UNDER A COVER?
Posted on Feb 21, 2009
Now these older dodges sometimes get a bad fuel relay after a while, when they start to go bad, sometimes it starts and sometimes it don't- because Almond joys got nuts- and. You have got toilet bowl injection-TBI-- Cuase typically a guy will swap out his fuel pump first!!!! (time and labour) dropping the tank blah blah--- Well anyhow that fuel relay (get yourself a hanes dodge truck repair book at Napa) is located in the engine compartment under the hood usually just off the battery above the starter side of the engine on top tho (accessable) Now the relay is around 10 to 13 bucks and swap that ****** out- and see, - the relay looks like a black plug in end of an extension cord, and has prongs when you detach it, some have 4 or 5,. Some trucks have 2 relays side by side. Well good luck and grab a neighbor and some beer and see if you all can't figure it out.
Posted on Jul 22, 2010
Tips for a great answer:
Mar 23, 2014 | 2001 Honda CR-V
Dec 11, 2010 | 1999 Chevrolet Blazer
May 10, 2010 | 1991 Chevrolet Lumina
Jul 04, 2017 | 1988 Chevrolet G20
Dec 15, 2008 | 1991 Ford Escort
Aug 10, 2008 | 1995 GMC Suburban
114 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: