Question about 1997 Acura TL Series

Open Question

1997 acura TL crankshaft position sensor location

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: blower motor for a 1997 acura tl

Unless you are an expert do not even attempt this. This is one of the first things that they put into the car, it requires you take off the entire dash, drop down the steering column, remove multiple vents / ducts, remove the chiller, remove screws from inside the engine compartment. This is at least a 10 hr job if you are good.

Posted on Nov 11, 2008

Ad
  • 416 Answers

SOURCE: how to remove door panel on 1997 acura tl

Follow this link. There is detailed step-by-step info here
Please kindly let me know if it works for you
Good Luck
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008c18d

Posted on Jan 31, 2009

emissionwiz
  • 77544 Answers

SOURCE: Where is the starter located on a 1996 Acura 2.5 TL?

it is at the rear bottom of engine, points inside the bell housing of the transmission, u will need to jack the car off the ground to see it and get at it for repAIR

Posted on Feb 28, 2009

emissionwiz
  • 77544 Answers

SOURCE: 2005 Acura TL Fuel Filter

the fuel filter for this is in the gas tank, it is part of the fuel pump module.

Posted on May 22, 2009

  • 60 Answers

SOURCE: where is plug in acura 2000 tl for check engine

The OBDII connector is located in the center console just behind the ashtray. There is a plastic cover that must be removed and you will find the connector behind the cover.

Posted on Jan 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Im doing a removal and installion crankshaft position sensor on my 1996 Acura T.L 2.5 my concern is if I remove the crank pully is automatically gonna jump timing. I got to as far that the only thing


The crank pulley comes off the crank itself...make a mark on pulley to crank/block (whatever is right there) shouldn't matter tho..may even b notched...

Sep 17, 2014 | 1996 Acura TL Series

1 Answer

Where is app throttle position sensor on 2004 acura tl


Obtain a Haynes Repair Manual from your local Auto Zone. They will go into great detail its location.

Apr 27, 2012 | 2004 Acura TL

1 Answer

1997 acura tl crankshaft spinning freely, is this normal? Just replaced a/c compressor and the pulley is turning real slow. Belt is not slipping. The crankshaft pulley and a/c pulley/belt rotate normally...


CHECK SEE IF CRANK SHAFT PULLEY BOLTS LOOSE.IF CRANKSHAFT PULLEY LONG BOLT TORQUE IS FOR 130 FT LBS FOR 1.8L ENGINE. IF YOU HAVE THESE ENGINES CRANKSHAFT BOLT TORQUE IS 174 - 181 FT LBS ENGINES ARE 3.0L 3.2L 3.5L 2.3L 2.5L IF CRANKSHAFT PULLEY BOLT IS TIGHT.THE CRANKSHAFT PULLEY ITSELF BROKEN NEED REPLACING.

Sep 05, 2011 | 1997 Acura TL Series

1 Answer

2000 Acura TL - The ODB says it is having random misfires. We have replaced the plugs and gotten the injectors cleaned. I'm at a loss as to what to check next. I've heard adjust the valves, but...


HAVE YOU CHECKED THE STATE OF THE IGNITION COIL(S)? IF THE CRANK SENSOR WAS FAULTY IT WOUD HAVE SHOWN UP AS AN OBD CODE, THE ECM CAN ALSO BE AT FAULT

Aug 25, 2011 | 2000 Acura TL

1 Answer

On 1996 Acura tl 2.5 where is located the speed sensor?


For 1996 Acura TL 2.5L PFI 5cyl the Vehicle Speed Sensor - Location is located mounted on transmission.


zjlimited_595.jpg


Fig.: Exploded view of the vehicle speed sensor (click for zoom).



Hope this helps (remember to rate this answer).

Feb 01, 2011 | 1996 Acura TL Series

1 Answer

Where is the crank shaft sensor located on a 2006 acura tl and how do i replace it? thanx


Crankshaft position sensor located on Right side of the engine. 1.remove the crankshaft pulley 2. remove the drive belt auto- tension 3. remove the upper cover and front covers from the engine 4. remove the crankshaft position sensor from the oil pump 5. Install tbe sensor in the reverse order of removal. Hope this can help .

Apr 17, 2010 | 2006 Acura TL

1 Answer

Check engine light still on, just resplaced crankshaft position sensor. where is rest switch


NO RESET SWITCH, U CAN CLEAR IT WITH A SCANNER OR U CAN DISCONNECT THE BATTERY FOR 5 MINUTES, PLEASE REMEMBER IF THE LIGHT COMES BACK ON U STILL HAVE A PROBLEM WITH THE SENSOR CIRCUIT, A CHECK ENGINE LIGHT ONLY MEANS THE CIRCUIT OR SYSTEM HAS A PROBLEM, THAT CAN BE THE SENSOR OR THE WIRING OR THE COMPUTER (KNOWN AS A PCM).

Nov 06, 2009 | 1997 Acura TL Series

Not finding what you are looking for?
1997 Acura TL Series Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...