Question about Cars & Trucks

Open Question

Acceleration switch circuit failure on 2000 ford ranger

Failure code c1102

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 883 Answers

SOURCE: 2000 Ford Ranger

TEST B: BATTERY VOLTAGE OUT OF RANGE - DTC B1676
1. Check if vehicle has been jump started within past 2 weeks. If vehicle has been jump started, ABS is
okay. If vehicle has not been jump started, go to next step.
2. Using DVOM, measure voltage between positive and negative battery terminals. If voltage is 9-19 volts,
go to next step. If voltage is not 9-19 volts, diagnose charging system. See appropriate GENERATORS
article in STARTING & CHARGING SYSTEMS.
3. Turn ignition off. Disconnect 25-pin ABS control module. Install EEC-IV 60-pin Breakout Box (014-
00322). Turn ignition on. Measure voltage between breakout box terminal No. 20 and ground. If voltage
is more than 10 volts, go to next step. If voltage is less than 10 volts, repair Light Blue/Pink wire between
ABS control module and instrument panel fuse panel.
4. Turn ignition off. Measure voltage between breakout box terminal No. 25 and ground. If voltage is
greater than 10 volts, go to next step. If voltage is less than 10 volts, repair Red wire between ABS
control module and power distribution box/engine compartment fuse box.
5. Measure voltage between breakout box terminal No. 9 and ground. If voltage is greater than 10 volts, go
to next step. If voltage is less than 10 volts, repair Yellow/Light Green wire between ABS control module
and power distribution box/engine compartment fuse box.
6. Measure resistance between breakout box terminal No. 8 and ground. Also, measure resistance between
breakout box terminal No. 24 and ground. If both resistance measurements are less than 5 ohms, replace
ABS control module and repeat self-test. If either resistance measurement is greater than 5 ohms, repair
suspect Black wire between ABS control module and ground distribution.
NOTE: DTC B1676 will set if vehicle has been jump started.
2000 Ford Ranger
2000-01 BRAKES Anti-Lock - 4WAL - Explorer, Ranger & Mountaineer

Posted on Jun 11, 2008

the recycler
  • 22 Answers

SOURCE: need location of the erg sensor 2000 ford ranger

The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Posted on Feb 25, 2009

  • 291 Answers

SOURCE: Code 224 on 1994 ford ranger. Checked primary

how did you check coils you can ohm them and they all should read the same... another way if you do not have an expensive scanner you can scope the current draw of each coil....or simply go to junk yard ...rob a set of coils and change all... do yourself a favor change plugs to standard autolite plugs.. let me know

Posted on Aug 31, 2009

  • 30 Answers

SOURCE: location of the egr sensor on 2000 ford ranger

Look on the top of the engine. The EGR valve is usually shaped like a UFO with a vacuum line going from the top of it to the EGR valve sensor. That's how it is with my 4.0L SOHC. Hope this helps. God bless

Posted on Oct 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, I have a 2000 Ford Ranger, 4L engine. How do I resolve an error code P1808? Thank you!


4WD ? - P1808 4WD Low Indicator Circuit Failure GEM GO to Pinpoint Test C . PINPOINT TEST C: THE 4X4 HIGH AND/OR 4X4 LOW INDICATOR(S) DO/DOES NOT OPERATE PROPERLY Sorry but nothing your going to be able to do except take to a qualified repair shop !

Oct 27, 2016 | Ford Ranger Cars & Trucks

1 Answer

92 ford ranger engine code 222


224 - Failure in ignition coil primary circuit (ignition systems.)

223 - Dual plug (DPI), SPOUT or IDM circuit fault. (Ignition systems.)

222 - IDM open or high or right coil pack failure. (Ignition systems.)

218 - IDM signal open or high or left coil pack failure. (Ignition systems.)

Mar 29, 2014 | Cars & Trucks

1 Answer

Abs light on codes 1095 1230 1102


C1095 refers to a noticed failure with the ABS pump motor. C1230 and C1102 refers to a failure with the rear ABS wheel speed sensor. You may have two separate issues but I think if you inspect the wiring, and it is fine. Replace the rear speed sensor and that should fix your problem. Please write back if you need more help, good luck.

Mar 08, 2014 | 1998 Ford Explorer

2 Answers

C1102 & c1230, I have these codes on my 1999 Explorer Sport. I would like to know where I can get pictures of where they are located.


this is an abs code. it means your rear abs sensor is bad. it is right in the middle of the rear axel on the top. it has wires going to it and looks like a little box

Mar 14, 2013 | Cars & Trucks

1 Answer

Hi I have a 2000 Ford Ranger and the air bag light is flashing


The light (on the key switch) that indicates whether the passenger airbag is on or off is, more than likely, burned out. You can either replace the whole switch ($$$) or you can take it apart and solder a new led into the circuit board. You can get the bulb at radio shack (make sure it is 12v). Good Luck!

Nov 17, 2009 | 2000 Ford Ranger SuperCab

1 Answer

2007 FORD RANGER TROUBLE CODES #B2292, B2293


These 3 codes have to do with restraint system.
B2292 Seatbelt pretensioner fault.
B2293 Passenger front airbag fault.
B2691 Seatbelt buckle switch circuit fault Ft.driver side.

Sep 18, 2009 | 2007 Ford Ranger FX4 Off-Road

2 Answers

Most common cause for code P0340 of 95 Ranger


Hi, the cam shaft sensor will be located Under the hood, center, upper engine area, mounted behind rear of intake manifold, in the engine block.


This is a magnetic or hall effect sensor. It sends a signal to the computer relaying information about shaft speed, position and acceleration or deceleration. This information determines when the fuel/air mixture needs to be ignited and how much mixture is needed for the engine.

The possible causes of failure will be faulty housing or faulty wires as well. A faulty ECM could trigger a false alarm as well. this is highly unlikely but, possible in most cases. The most reported reasons is flat out sensor failure.

May 21, 2009 | 2001 Ford Windstar

1 Answer

Replaced wiring harness on 2000 Ford Ranger now truck won't start


2000 ford ranger wont start off switch if u jump the silanoid it will start. new start and ignition switch

May 06, 2009 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

933 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...