Question about 1999 Dodge Durango

Open Question

Is the drivers side front axle nut right or left hand threads on my 1999 durango

The wheel bearing is bad. I have the new hub assembly just cant get the axle nut to break loose.

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: nut or the end of the axle

Get a strong socket and a log breaker bar. I have a 4 foot breaker bar that hold 3/4 drive sockets. Mine was tight also but it came loose with that bar. The only other suggestion would be to heat it up quickly with a torch and go for it.

Posted on Feb 18, 2009

  • 1 Answer

SOURCE: 2002 dodge ram 4WD front hub bearing

Here is the easiest way . take a 14mm socket and extentsion and place it on the bolts and place againt your axle tube and start your truck and turn your wheel against it instead of pounding you will use your powersteering like a press to get your hub out its quicker and less strenous than pounding on the bolts ive done this many times i even made a extentsion for it i use a 14mm 1/2 drive shallow socket and a extension thats about 4 inches long i know im posting late on this one but if it helps anyone out then great

Posted on Nov 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install rear struts on a 1999 llexus


selectachapter.gif

Lexus Car ES, IS, LS 1998-06
Coil Spring Rear Suspension

Print


Hub & Bearings

Adjustment
Check the backlash in bearing shaft direction and the axle hub deviation. Maximum for backlash should be 0.0020 in. (0.05mm) and for axle hub deviation 0.020 in. (0.05mm).

7923lgb6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Checking wheel bearings for excessive play


NOTE The rear wheel bearings are non-adjustable. If the wheel bearing is out of specifications, replace the wheel bearing.
Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:

    Rear tire and wheel assembly Rear stabilizer link Rear axle shaft nut Rear disc brake caliper and disc Speed sensor Parking brake assembly at the wheel hub No. 1 and 2 upper control arm assembly No. 1 and 2 rear suspension arm assembly Toe control link Rear axle from hub assembly using a plastic hammer No. 2 rear wheel bearing dust deflector using a screwdriver 4 bolts and rear axle hub and bearing assembly from the axle carrier assembly

To install:
  1. Install or connect the following:

    Hub on the carrier and tighten the bolts to 52 ft. lbs. (70 Nm) No. 2 rear wheel bearing dust deflector using a screwdriver Rear axle into hub assembly No. 1 and 2 upper control arm assembly. Torque the new nut to the No. 2 rear upper control arm to 52 ft. lbs. (70 Nm). Temporarily tighten the No. 1 arm bolt. No. 1 and 2 rear suspension arm assembly. Temporarily tighten. Toe control link. Torque new nut to 52 ft. lbs. (70 Nm). Rear stabilizer link. Torque to 20 ft. lbs. (27 Nm). Parking brake assembly at the wheel hub Rear speed sensor Rear axle shaft nut. Torque to 214 ft. Lbs. (290 Nm) and stake the nut with a chisel and hammer. Rear brake disc and disc brake caliper
  2. Adjust the parking brake.
  3. Stabilize the suspension as follows :
    1. Install the wheel(s).
    2. Lower the vehicle and bounce it up and down several times to stabilize the rear suspension.
    3. Raise the vehicle.
    4. Remove the wheel.
    5. Jack up the rear lower suspension armplacing a wood block in between. Apply a load to the suspension so that the lower suspension arm is plkaced in a horizontal position.

  4. Fully tighten the No. 1 rear upper control arm assembly to 119 ft. lbs. (161 Nm).
  5. Fully tighten the No. 1 rear suspension arm assembly to 70 ft. lbs. (95 Nm).
  6. Fully tighten the No. 2 rear suspension arm assembly to 119 ft. lbs. (161 Nm).

    Rear tire and wheel assembly

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:
    NOTE If it is necessary to replace the hub or bearing, replace the components as an assembly.


    Rear tire and wheel assembly If equipped with rear disc brakes, the caliper mounting bolts. Leave the brake line connected and suspend the assembly out of the way. Brake rotor or drum 4 bolts and pull off the rear axle hub O-ring

To install:
  1. Install or connect the following:

    Hub on the carrier and tighten the bolts to 59 ft. lbs. (80 Nm) Rotor or drum Caliper, f equipped with rear disc brakes and tighten the bolts to 34 ft. lbs. (64 Nm) Wheel

  1. Before servicing the vehicle, refer to the Precautions section.
  2. If equipped with air suspension, move the height control switch in the trunk area to the OFF position.
  3. Remove or disconnect the following:

    Negative battery cable Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Cotter pin, lock cap and the nut holding the halfshaft to the rear axle Suspension member brace by removing the 2 bolts Halfshaft bolts and washers Halfshaft from the vehicle Strut rod
  4. Place matchmarks on the adjusting cam and body for the No. 1 control arm.
  5. Remove or disconnect the following:

    Nut and adjusting cam Nut on the axle carrier side of the No. 1 lower control arm Separate the control arm from the axle carrier No. 1 lower control arm Stabilizer bar link from the No. 2 lower control arm.
  6. Place matchmarks on the adjusting cam and body.
  7. Remove or disconnect the following:

    Nut and adjusting cam from the No. 2 lower control arm Nut and bolt holding the No. 2 lower control arm to the axle carrier No. 2 control arm from the vehicle Nut and bolt on the lower side of the strut assembly 2 upper control arm set nuts and bolts Axle carrier with the upper control arm
  8. Secure the axle carrier in a vise.
  9. Remove or disconnect the following:

    Nut holding the upper control arm to the axle carrier and remove the control arm Dust deflector. Use a suitable prytool. Oil seal

    0996b43f802092da.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the oil seal (inner)-LS 430

  10. Remove the 2 bolts and nuts and shift the backing the plate towards the hub side (outside).
  11. Remove or disconnect the following:

    Axle hub

    0996b43f802092db.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the axle hub from the axle carrier-LS 430
    Backing plate. Inner race (outside) from the axle hub

    0996b43f802092dc.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the inner race (outside) from the axle hub-LS 430
    Oil seal (outer) from the axle

    0996b43f802092dd.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the oil seal (outer)-LS 430
    Snapring from inside the axle housing Bearing from the axle housing


To install:
  1. Install or connect the following:

    New bearing to the axle housing Snapring to the axle carrier, using snapring pliers New outer oil seal. Coat the oil seal lip with multipurpose grease.

    0996b43f802092de.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Installing the oil seal (outer)-LS 430
    Backing plate to the axle housing. Do NOT install the bolts or nuts at this time. Inner race (inside) to the axle housing Axle hub to the axle housing Backing plate in position. Tighten the bolts and nuts to 43 ft. lbs. (59 Nm). New oil seal (inner) to the axle housing. Coat the oil seal lip with multipurpose grease.

    0996b43f802092e0.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Installing the oil seal (inner)-LS 430
    New dust deflector. Be sure to align the hose for the ABS speed sensor in the dust deflector and axle carrier. Upper control arm to the axle carrier by installing the nut. Tighten the nut to 80 ft. lbs. (108 Nm). Axle carrier and upper control arm to the vehicle as an assembly 2 upper control arm set bolts and tighten the bolts to 121 ft. lbs. (164 Nm) Bolt and nut holding the strut to the axle carrier. Tighten to 101 ft. lbs. (137 Nm). Bolt and nut connecting the No. 2 lower control arm to the axle carrier. Tighten the bolt to 60 ft. lbs. (81 Nm). Nut and adjusting cam to hold the No. 2 lower control arm to the body. Align the adjusting cam marks and tighten the nut to 57 ft. lbs. (78 Nm). Stabilizer bar link to the No. 2 lower control arm and tighten the nut to 48 ft. lbs. (65 Nm) No. 1 lower control arm to the axle carrier and body. Install the nut to hold the No. 1 lower control arm to the axle carrier. Tighten the nut to 43 ft. lbs. (59 Nm). Nut and adjusting cam to hold the No. 1 lower control arm to the body. Align the matchmarks and tighten the nut to 57 ft. lbs. (78 Nm). Strut rod to the axle carrier and body. Install the bolt and nut to hold the strut rod to the body. Tighten to 57 ft. lbs. (78 Nm). Bolt and nut to hold the strut rod to the axle carrier. Tighten to 136 ft. lbs. (184 Nm) Parking brake shoes and cable Outboard joint side of the halfshaft and align the matchmarks on the side gear shaft and the halfshaft. Coat the threads with clean oil and install the hexagon bolts. Tighten bolts to 61 ft. lbs. (83 Nm). Suspension member brace with the 2 bolts. Tighten the 2 bolts to 37 ft. lbs. (50 Nm). Nut to hold the halfshaft to the rear axle. Tighten the nut to 213 ft. lbs. (289 Nm). Lock cap and cotter pin Brake disc to the axle hub with the matchmarks aligned. Install the 2 screws and tighten the screws to 48 inch lbs. (5 Nm). Brake caliper to the vehicle and install the 2 bolts. Tighten the bolts to 77 ft. lbs. (104 Nm). ABS speed sensor and wiring harness Height control sensor link with the matchmarks aligned. Tighten the nut to 48 inch lbs. (5 Nm). Rear wheel(s) Negative battery cable

  2. Lower the vehicle and turn ON the air suspension switch.



0996b43f80207fdc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Exploded view rear carrier assembly, hub and bearing-

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    WARNING Be careful not to damage the boot and ABS sensor


    Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Toe control link Separate upper control arm assembly Shock absorber from axle carrier Suspension arms No 1 and 2 from axle carrier Rear axle from carrier


    Wheel bearing dust deflector 4 bolts and axle & bearing hub assembly

To install:
  1. Install or connect the following:

    4 bolts and axle & bearing assembly. Tighten to 48 ft. lbs (65 Nm) Rear wheel bearing dust deflector Rear drive axle Upper control arm. Temporarily tighten No 2 and No 1 suspension arms. Tighten to 52 ft. lbs. (70 Nm) Shock absorber. Temporarily tighten Toe control link. Tighten to 37 ft. lbs. (50 Nm) Fully tighten upper control arm. Tighten to 52 ft. lbs. (70 Nm) Height control sensor Parking brake shoes and cable Speed sensor Rear disc brake caliper Fully tighten shock with new nut to 52 ft. lbs. (70 Nm) Rear tire
  2. Inspect and adjust rear wheel alignment
  3. Check ABS speed sensor signal

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Rear wheel Wheel speed sensor Axle halfshaft Brake caliper and rotor Parking brake shoes Parking brake cable No. 1 lower suspension arm bolt No. 2 lower suspension arm bolt Toe control link Upper ball joint Axle carrier from the vehicle
  3. Press the hub out of the wheel bearing, then remove the backing plate.
  4. Remove the snapring, then press the wheel bearing out of the axle carrier.

To install:

NOTE Use a new toe control link nut for assembly.
  1. Installation is the reverse of the removal procedure, while using the following torque values:

    Backing plate bolts: 43 ft. lbs. (59 Nm) No. 1 lower suspension arm bolt: 55 ft. lbs. (75 Nm) No. 2 lower suspension arm bolt: 81 ft. lbs. (110 Nm) Toe control link nut: 36 ft. lbs. (49 Nm) Upper ball joint nut: 80 ft. lbs. (108 Nm) Brake caliper support bolts: 77 ft. lbs. (104 Nm) Rear wheel lug nuts: 76 ft. lbs. (103 Nm)



0996b43f80208026.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Exploded view rear Axle carrier and hub assembly-ES 330

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Rear tire and wheel assembly Brake caliper support bracket Brake rotor Skid control sensor wire 4 bolts and rear hub and bearing assembly Skid control sensor

To install:
  1. Install or connect the following:
    NOTE Inspect bearing back lash and hub deviation


    Skid control sensor Rear axle hub and bearing assembly with 4 bolts. Tighten to 59 ft. lbs. (80 Nm) Skid control sensor wire


    Rear disc Rear disc brake caliper assembly. Tighten to 46 ft. lbs (62 Nm) Flexible brake hose Rear tire and wheel
  2. inspect and adjust rear wheel alignment
  3. Check ABS speed sensor signal


Stabilizer Bar

Removal & Installation

  1. Remove the rear wheels.
  2. Remove the 2 nuts and left stabilizer bar link. If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud. Repeat for the right side.
  3. Remove the 8 bolts, 2 No. 1 brackets and 2 bushings. Two types of bolts are used, so make sure the correct bolts are installed.
  4. Remove the stabilizer bar.

To install:
  1. Install the stabilizer bar.
  2. Install the bushing and bracket with the 2 bolts and tighten to 14 ft. lbs. (19 Nm). Install the bushing to the inner side of the bushing stopper on the stabilizer bar.
  3. Connect the stabilizer bar links and tighten the nuts to 29 ft. lbs. (39 Nm). Repeat for the right side.
  4. Install the rear wheels.
  5. Inspect and adjust rear wheel alignment.


Strut & Coil Spring

Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    CAUTION Do NOT remove the center nut to the strut at this time. The spring on the strut is under high pressure and can cause serious injury.


    No. 2 luggage compartment trim cover Left and right deck side trim box Rear luggage compartment trim cover Front luggage compartment trim cover Left and right side luggage compartment trim covers Rear wheel Rear wheel fender liner No. 2 differential support protector Rear suspension member brace Rear No. 2 lower control arm Mounting bolts and strut assembly
  3. Secure the strut in a vise.
  4. Compress the coil spring
  5. Remove or disconnect the following:

    Upper strut retaining nut Suspension support Upper insulator Bumper Coil spring Insulator

Dec 26, 2011 | 1999 Lexus ES 300

3 Answers

I cant get the front hub assembly off my 03 buick rendevous


Items/Tools needed:

35mm or 1 3/8" axle socket
3/4 or 19mm socket for lug nuts or lug wrench
15mm socket for brake caliper and bracket
13mm socket for wheel bearing bolts (extentions as well)
Breaker bar or impact wrench to remove lug nuts and axle nut (Note: Do not use impact driver to install axle nut).
Torque wrench for axle nut
Hub puller - Optional
Hammer

Directions

1. Jack the appropriate side of the car up. Make sure the rear wheels are blocked and/or set the parking brake. Use a jackstand to support vehicle at subframe for safety.
2. Remove wheel.
3. Remove brake caliper and bracket.
4. Remove rotor.
5. Using 35mm axle socket, remove axle nut, turn counterclockwise. You will either need an impact or a long breaker bar. They are installed with a lot of torque or may be rusted out or corrroded.
6. Push the axle back as far as possible. It won't come all the way out or through the hub, but will become loose. You can either get a tool that will push it out like a hub puller, or just use a hammer making sure not to hit the axle shaft threads and damage them. Put the axle nut back on the axle shaft so it is flush with the top. Then place 35mm axle nut socket on the axle nut and tap on the 35mm socket with the hammer not the threads on the axle shaft spline.
7. Disconnect the wheel sensor connector and then remove hub side connector from the bracket (unclip).
8. Take a 13mm socket with extensions as needed and remove the 3 bolts on the backside of the bearing around the axle. Be sure to use PBBlaster to help loosen the bolts.
9. The hub/bearing should come loose without need needing a hub puller. Be sure to note the sheet metal spacer between the hub and spindle with also has the bracket for the wheel sensor connector.
10. Double check both parts (hubs) to make sure they match.
11. Lube the axle shaft splines with good quality bearing grease before installing the hub. Clean off any old grease and crud first.
12. Install the hub assembly with the wires from the bearing at the bottom. Line up hub splines with axle shaft splines and push in on hub. Note: Don't forget that sheet metal plate between the spindle and wheel bearing. Note: Make sure the wheel sensor wires don't get pinched by the axle shaft.
13. Install the 3 13mm bolts to 96ft lbs. Service manual recommends replacing with new ones. Some hubs like AC Delco will come with new bolts which have threadlocker.
14. Install the axle nut. As tightened down it will pull the driveshaft the rest of the way in. Torque axle nut to GM specs of 159 ft-lbs or the figure specified by the hub manufacturer. It is recommended to use a new axle nut but not necessary.
15. Install the rotor, brackets and caliper. Torque caliper bracket bolts to 137 ft-lb and caliper pin bolts to 63 ft-lb.
16. Install the connector to the sheet metal bracket and reconnect both connectors.
17. Install the wheel. Torque lug nuts in a star pattern at 100 ft-lbs each.
18. Road test car and ensure any ABS and TRAC OFF light are off.

Sep 18, 2011 | 2003 Buick Rendezvous

1 Answer

How do I rgerplabe how do I replace a front wheel bearing?


TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Mar 21, 2011 | 1999 Oldsmobile Alero

1 Answer

I'm trying to remove the axle nut on my 1999 Dodge Ram 2500. I can't remember if they are left or right hand threads. Any suggestions? I'm working alone on this issue, trying to get to the wheel hub...


sould be standard left to loosen,, make sure you soak it with PB blaster or Kroil,, I've spun the nuts, before(plow trucks) and had to buy the stub shaft(dealer only $$$) and new U joints,, Keep soaking it!!! Hub bearings are pricey also,, good luck,, You will have to use the jaws to pull it off, and the bolts on the back side, soak those,, I ve separated the hubs before, and then i ve had some come off easy,, Good luck,, total fix $350-$1200 per side. keep soaking, is all i'm saying...

Dec 18, 2010 | 1999 Dodge Ram 2500 4WD

3 Answers

Right front wheel bearing is bad how do I change it


  1. Raise and support the vehicle safely. Place jackstands under the frame, then lower the vehicle slightly to allow the control arms to hang free.
  2. Remove the tire and wheel assembly.
  3. Insert a drift punch into the caliper and rotor vanes to prevent the rotor from turning, then remove the hub/drive axle nut. Clean the threads of the nut.
    1. Unfasten the caliper mounting bolts, then remove and support the caliper aside with a suitable piece of wire.
    2. Remove the rotor by sliding it from the hub.
    3. If equipped with ABS, detach the front wheel speed sensor connector and unclip it from the dust shield.

    The hub and bearing are replaced only as an assembly.
    For 1987-92 vehicles, perform the following:
  4. Using a suitable front hub spindle removal tool, separate the hub from the halfshaft.
  5. Remove the hub and bearing retaining bolts, shield, hub and bearing assembly and the O-ring.
  6. Separate the ball joint from the steering knuckle, using the proper tool.
  7. Remove the halfshaft assembly and tap the seal from the steering knuckle. Remove the steering knuckle from the hub.
  8. For 1993-99 vehicles, perform the following:
    1. Unfasten the hub and bearing retaining bolts and dust shield.
    2. Place the transaxle in PARK.
    3. Using a suitable front hub spindle removal tool, separate the hub and bearing from the drive axle.
    4. If necessary, remove the steering knuckle.

  9. Clean the rust and foreign material from the knuckle mounting face, bore and chamfer to allow the bearing to properly seat in the knuckle.
To install:
  1. For 1993-99 vehicles, perform the following:
    1. If removed, install the steering knuckle.
    2. Position the hub and bearing assembly to the drive axle. Apply a light coating of grease to the knuckle bore. If the new hub and bearing has a protective plastic cover, remove it before installation. Also, do not handle the knuckle or hub assembly by the ABS sensor wire.
    3. Install a new drive axle nut and draw the hub and bearing onto the axle.
    4. Place the transaxle in NEUTRAL.
    5. Install the dust shield, being careful not to damage the bearing outboard lip seal.
    6. Install the hub and bearing bolts, then tighten to 70 ft. lbs. (95 Nm).

  2. For 1987-92 vehicles, perform the following:
    1. Install a new hub and bearing seal in the steering knuckle with a suitable seal installation tool. Install the steering knuckle to the strut.
    2. Lubricate the hub and bearing with grease. Fill the cavity between the seal and bearing completely.
    3. Install the halfshaft.
    4. Connect the ball joint to the steering knuckle and insert a new O-ring around the hub and bearing assembly.
    5. Install the hub and bearing, and shield into the steering knuckle. Tighten the bolts to 70 ft. lbs. (90 Nm).

  3. If equipped, attach the ABS front wheel speed sensor connector, then clip the wire to the dust shield.
  1. Install the rotor and caliper assembly. Tighten the caliper bolts to 38 ft. lbs. (52 Nm).
  2. Insert a drift punch into the caliper and rotor vanes to prevent the rotor from turning. If not already done, install the shaft washer and nut (if equipped). Tighten the nut to the following specifications:
  3. 1987-88 vehicles: 3 ft. lbs. (270 Nm).
  4. 1989-90 vehicles: 15 ft. lbs. (260 Nm).
  5. 1991-99 vehicles: 107 ft. lbs. (145 Nm).
  6. Install the tire and wheel assembly.
  7. Carefully lower the vehicle, then tighten the lug nuts to 100 ft. lbs. (136 Nm).
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 21, 2010 | 1995 Buick LeSabre

1 Answer

What is needed to remedy right hand front wheel bearing play on a 1990 d21 4X4 ute


replace the bearing or wheel hub assembly.

REMOVAL & INSTALLATION 2wd Models NOTE: Refer to wheel bearing service and bearing preload adjustment procedures found in Section 1.
  1. Raise the front of the truck and support it with safety stands. Remove the wheels.
  2. Remove the brake caliper and suspend it with wire, out of the way. Remove the caliper torque plate if equipped.
  3. Remove the dust cap and then remove the cotter pin, lock washer (if equipped) nut lock and nut.
  4. Pull the hub/disc assembly off the spindle with the outer bearing. Don't let the bearing fall out.
  5. Pry the inner oil seal out and remove the inner bearing. To install:
  6. Clean and inspect the bearings and outer races.
  7. Using a brass drift and a hammer, drive out the bearing outer race. Press a new one into position.
  8. Pack the bearings with grease until it oozes out the other side. Coat the inside of the hub and cap with grease.
  9. Position the inner bearing into the hub, coat the oil seal with grease and press it into the hub.
  10. Press the hub assembly onto the spindle and install the outer bearing and thrust washer.
  11. Install the hub nut. Turn the hub a few times to seat the bearings and then loosen the nut until there is 0mm axial play. Using a spring tension gauge, check that the preload (with new grease seal installed) is 2.2–6.4 lbs. (9.8–28.4N)
  12. Install the lock-nut, new cotter pin and hub grease cap.
  13. Install the brake torque plate. Install the brake caliper.
  14. Install the wheels and lower the truck.
4wd Models The hub and bearing service procedures for a 4wd models are basically the same as those for a 2wd version, with the exception of removing the free running hub assembly and the bearing preload adjustment. Refer to Sections 1 and 7 for additional information. Adjust the preload after the wheel bearing is replaced or the front axle assembly is reassembled. BEARING PRELOAD ADJUSTMENT
  1. Thoroughly clean all parts and pack the wheel bearings.
  2. Apply grease to threaded portions of the spindle, grease seal lip and wheel hub.
  3. Tighten the wheel bearing lock-nut with a socket and torque wrench to 58–72 ft. lbs. (78–98 Nm).
  4. Rotate the hub in both directions a few times to seat the bearings. Loosen wheel bearing lock-nut.
  5. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm).
  6. Turn wheel hub several times in both directions.
  7. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm). Fig. 1: Exploded view of the front axle assembly — 2wd models 86718030.gif
    Fig. 2: Removing the bearing outer races 86718032.gif
    Fig. 3: Packing the wheel bearing with grease 86718033.gif
    Fig. 4: Pack the lip cavity of grease seal with grease 86718034.gif
    Fig. 5: Exploded view of the front axle assembly — 4wd models 86718031.gif

  8. Measure wheel bearing axial end-play. The wheel bearing end-play specification is 0.
  9. Install lock washer by tightening the lock-nut within 15–30 degrees.
  10. Turn wheel hub several times in both directions. Wheel bearing should be seated correctly.
  11. If necessary, measure wheel bearing preload. NOTE: Measure wheel bearing preload with a spring-type gauge; measure at wheel hub bolt, with tire removed. The hub assembly should rotate with 1.6–4.7 lbs. (0.73–2.13 kg) of pressure.
prev.gif next.gif

Jul 28, 2010 | 1991 Nissan Pickup

2 Answers

Front wheel bearing repair


There's no repair to the hub bearing assembly, seal unit, to replace first remove axle nut ( 32 or 36 mm) might need some one to step on brake while removing nut, so it done turn on you, remove front brake caliper and caliper bracket, then remove brake rotor, on back side of hub bearing there three bolt's, remove, hub bearing should slide out, some time with a little help from a hammer, install new hub bearing.

Jul 15, 2010 | 1999 Ford Taurus

1 Answer

How long does it take to fix front bearings on a 97 dodge caravan? and cost


About an hour a side...This is the whole job and pictures....

The hub and wheel bearing unit is serviced as a complete assembly. Replacement of the front drive hub and bearing assembly can be done without having to remove the steering knuckle from the vehicle. However, if the hub/bearing assembly is frozen to the steering knuckle, removal of the steering knuckle is required.
  1. Disconnect the negative battery cable.
  2. Remove the cotter pin from the end of the stub axle. Remove the nut lock and spring washer. With the brakes applied, loosen, but do NOT remove the axle nut and washer with the vehicle still on the ground or damage to the wheel bearing will result.
  3. Raise and safely support the vehicle. Remove the wheel.
  4. Remove the front brake caliper assembly from the steering knuckle assembly and support from the strut assembly using a strong piece of wire.
    1. Remove the front brake rotor from the hub/bearing assembly.
    2. Remove the retaining nut and washer from the halfshaft stub axle.
    3. Remove the ABS wheel speed sensor from the steering knuckle.
    4. Remove the 4 hub and bearing assembly mounting bolts from behind the steering knuckle.
    5. Remove the hub and bearing assembly from the steering knuckle.
  5. To install:
    1. Thoroughly clean the mating surfaces of the steering knuckle and the hub and bearing assembly of any foreign material or nicks so the surfaces are clean and smooth.
    2. Install the new hub and bearing assembly and tighten the mounting bolts in a crisscross pattern to 45 ft. lbs. (65 Nm). Be sure the hub and bearing assembly is seated squarely against the front steering knuckle.
    3. Install the disc brake rotor.
    4. Install the brake caliper assembly onto the steering knuckle.
    5. Install the axle washer and nut. Tighten but do not torque.
    6. Install the ABS wheel speed sensor.
    7. Install the wheel and lug nuts. Torque the lug nuts, in sequence, to 95 ft. lbs. (129 Nm).
    8. Lower the vehicle. Do NOT roll the vehicle until the axle nut has been properly torqued or damage to the front wheel bearings will result.
    9. With the vehicle's brakes applied, torque the axle nut to 180 ft. lbs. (244 Nm). Install the spring washer, nut lock and a new cotter pin. Wrap the cotter pin prongs tightly around the axle nut lock.
    10. Reconnect the negative battery cable. Check the wheel alignment.

fe8edd6.gif
The hub/bearing assembly is attached to the steering knuckle with four bolts


9733319.gif
Removing a hub/bearing assembly



1867b08.gif
If the hub/bearing is "frozen" to the steering knuckle, separate the ball joint and lightly tap on the hub/bearing from behind



09233ac.gif
The hub/bearing assembly should free itself from the steering knuckle

About $60 a hub.

May 23, 2010 | 1997 Dodge Caravan

1 Answer

I need an exploded view diagram to see how the RIGHT FRONT wheel HUB ASSEMBLY is installed on my 1997 Mitsubishi Galant. Will I have to mess with the CV, or is it a "bolt off-bolt on" procedure. I'm very...


db7ecae.gif#2 = Hub assembly.
It is a pretty simple process and yes you need to mess with the CV but not much. An impact wrench will make removing the large nut holding the axle in the hub/bearing a whole lot easier. If you have one great, if not, it would be best to try loosening the nut while the car is on the ground. If your car has steel rims with hubcaps(MAGS, I'd put on the spare for this part), start by removing the hubcap then remove the cotter pin that goes through the threaded part of the axle and keeps the nut from coming loose. You may want to spray on some WD-40 and let it soak a little before u start. A breaker bar and socket work well, if u have just a rachet, try to find a 4 foot metal / aluminum tube (old tent pole) and slip it over the handle to give you some more torque to loosen the nut. Once loose, back the nut off and push on the axle shaft to see if it moves, probably won't, so more WD-40. You can raise and support the car, remove the wheel and brake caliper and rotor, that should be plenty of time for the WD-40 to work. Try moving it again, if it moves great, if not, hammer time. If you have a large puch or something comparable use it, you really don't want to damage threads. Leave the nut on the axle just in case you do hit the thread, when the axle is moving, take the nut off and this will straighten out the thread if it was damaged. Only thing left now is to remove the 4 bolts holding on the HUB/BEARING assembly. Once they're out it should slide off the axle with out any problems. Slide on the new one and bolt it back together. ONE CAUTION to note DO NOT MOVE THE CAR IF THE AXLE NUT ISN'T TIGHT, YOU'LL SCRAP THE BEARING!!! Here is a link just to show you what the hub assembly looks like from both sides. Hope this is of some help.
http://cgi.ebay.com/ebaymotors/PAIR-GALANT-FRONT-WHEEL-HUB-BEARING-96-97-98-99-00-01_W0QQcmdZViewItemQQhashZitem45eebc4965QQitemZ300358060389QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

Nov 25, 2009 | Mitsubishi Galant Cars & Trucks

2 Answers

How can I remove the spindle nut? It seems to be


itll come just use a bigger diameter hose and higher pressure. You can use alil heat if your replaceing the hub and bearing but i still wouldnt recommend it.

Jul 17, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
1999 Dodge Durango Logo

Related Topics:

497 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...