Question about Toyota Camry

Open Question

Camry 2009 headlight adjustment

Where are the headlight adjusting screws on a 2009 camry?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1997 Tahoe Headlight Adjustment

the two large screws on top are to remove light totally.You need to look down the holes with a flash light to see the adjustments.

Posted on Dec 11, 2008

Ad
  • 1986 Answers

SOURCE: Can't find headlight adjustment screws

They nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.


Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 17, 2009

Testimonial: "The adjustment screw (for passenger side) is located between the battery & frame's second hole. Turning counter-clockwise, it adjusts downwards,Thanks"

  • 1986 Answers

SOURCE: Headlight adjustment instructions

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams: Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

  • 1986 Answers

SOURCE: Headlights

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

  • 1986 Answers

SOURCE: 1998 Ford Mustang Headlight Adjustment

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to adjust the horizontal dim lights 2009 camry


Replace Headlight on Toyota Camry SE 2010 - YouTube

? 9:59
www.youtube.com/watch?v=aPf_PtUykSo
Sep 14, 2013 - Uploaded by Mon Boonprohm I need to replace both my headlamp assemblies on a 2009 ToyotaCamry and the 2006 ... I just replace the headlights on my 2004 Jeep Grand.

Oct 14, 2015 | Cars & Trucks

1 Answer

How do I aim the headlights


There ate two adjustment one up and down the other left and right
there on hoiseing the a Phillips head screwdriver.

Mar 15, 2015 | 2009 Toyota Camry

1 Answer

Aiming of the headlights


Hello sent some pic through
thank you please reply

Mar 15, 2015 | 2009 Toyota Camry

1 Answer

Headlights


Yes, all cars have two adjustments per headlight, one screw for up and down and the other for left and right. Any garage will have headlight aimers, Or when you locate the screws you can adjust them by pulling up to a garage door and turning them on.

Jan 29, 2014 | Cars & Trucks

1 Answer

How do you adjust the headlights


After you disassemble the head light housing there should be a threaded adjustment screws that will allow you to tilt the headlights up or down. Technically your suppose to go to a shop that has the machine to "dial" it in properly but it can be done on your own. Just pull the car 10 feet away from a wall and turn the headlights on and make sure you can see them on the wall clearly (may have to do it at night). Make a mark on the wall to the height you would like to adjust them and zero them in using the adjustment screws. Hope this helps!

Dec 23, 2010 | 1998 Toyota Camry

2 Answers

How do I adjust the headlights on my 2010 dodge ram 2500?


On the fender there is a hole with an arrow embossed in the metal.Use a t-20 torx driver and adjust as needed.

Nov 15, 2010 | 2010 Dodge Ram Pickup 1500

2 Answers

CRV headlights


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Aug 07, 2009 | 2009 Honda CR-V

1 Answer

Headlight adjustment instructions


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams: Aim the headlight directly at the line you marked on the wall.

May 05, 2009 | 1998 Toyota Camry

1 Answer

Headlight adjustment


I had this problem. The plastic grommet that the headlight fit into was cracked. I got a headlight assembly from CertiFit (cheaper than dealer.) Or try a junkyard.

Nov 11, 2008 | 1994 Toyota Camry

1 Answer

Headlight adjustment


park it in front of a garge turn the lights on there should be two screws on each headlight the one on the top adjusts up and down the other right to left

Oct 06, 2008 | 1989 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

475 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...