Question about 2004 Cadillac SRX

Open Question

Steps on how to replace evap canister purge solenoid valve 2004 cadillac srx

Dont wnt to pay dealer 500 dollars in labor for a 25 dollar part need to know steps to r&r

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
MrScary66613
  • 1990 Answers

SOURCE: 1997 CADILLAC DEVILLE D' ELEGANCE need to replaced air suspension

Try going to a Local Mechanic or Repairing them Yourself. Either way is a LOT Cheaper.

Posted on Jan 21, 2009

Ad
  • 4 Answers

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

WikiAnswers
http://wiki.answers.com/Q/How_to_change_the_Cadillac_SRX_Front_Tun_Signal_Bulb

Posted on Feb 17, 2009

  • 32 Answers

SOURCE: when does cadillac catera need a tuneup and what is tuneup

tuneups consist of changing fuel filters air filters spark plugs and shouldbe done every 5000 kms or every six months depends on what comes first

Posted on Apr 12, 2009

techbuster
  • 5081 Answers

SOURCE: rear liscese plate bulbs on 05 cadillac srx

First you have to take out the one and only screw in the rear hatch door - it's where the hand pull down is you use to close the hatch.
Then you have to pop all the plastic clips all the way around the plastic door panel, trying not to pull them out from the frame . If you do pull out the white plastic plugs from the frame you better make certain you take them off the plastic housing and insert them back into their frame holes - or you will never get the housing back on.

Once you have the housing loose disconnect the inside tail gate light wire to remove the whole thing. Then you have to remove 7 to 8 nuts from the back of entire License plate, back up bulb housing using a deep socket to get in there. Work it loose from the rear of the car and it will come out just enough to work on the lights.
This is tricky since the screw mounts don't give you much room to work with.

Once you have the license plate and back up bulb frame loose you will see the two housings for the license plate bulbs on top.

Slide out the license plate bulb lens and twist the bulb connection to remove the bulbs.
Replace both of them - you don't want to do this again in a month when the other one blows.

OPTIONAL:
Once you take out the bulbs you might see that the housing is melted where the bulb wanted to burn through. Drill two small holes one is each end of the housing before I put everything back together to release some of the heat.


Reverse the whole process to put everything back together. It's not easy.
Make sure you insert the cables through the opening for the hatch handle or it will kink and not work properly.

The bulbs come in a two pack of cost $4.95 .

Posted on Nov 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Back door dont wnt to open...how much to fix it ....john


This is usually due to a broken release handle, if the handle feels loose and like there is nothing attached to it then that's the case, the handle is about $25 and the labor at the dealer around $200.

Aug 19, 2011 | 2001 Toyota Sequoia

1 Answer

Driver Side window is stuck and cannot get it to close. Thinking it's the motor, but could it be a fuse?


it is time to go buy a new window regulator. parts store and eBay are good sources. pay an auto glass shop to put it in. you are not going to do this yourself. dealer about 500 dollars, as much as the car is worth, do it my way about 150 dollars total.

May 16, 2011 | 1997 Pontiac Bonneville

2 Answers

How much should it cost to replace the water pump?


if i remember right it is about 2 hours labor time, $150-$300 depending on the shop labor rate and the pump should be about $100-$200 dollars depending on the supplier and shop mark-up. so $250-$500 dollars roughly.

Jan 04, 2011 | 2003 Chevrolet Suburban 1500

1 Answer

MY CAR NEEDS A NEW AXLE AND 4 BRAND NEW TIRES. I WOULD LIKE TO KNOW THE ESTIMATION OF HOW MUCH IT WILL COST TO GET IT FIXED?


At a shop your looking at roughly $60 - $100 dollars a tire mounted and balanced. The drive axle will run you a couple hundred dollars for labor and a couple hundred for the part.

So total you would be in the $500 - $800 dollar range depending on the quality of the tires, the shop you choose, and the shops labor rate.

Oct 05, 2010 | 2001 Kia Optima

2 Answers

Speedometer does ot work


Pretty common problem with these. Here's a guide to learn how to fix GM instrument clusters yourself, I used it to fix mine and it worked great. How to guide for Silverado instrument cluster repair
How to guide for Silverado instrument cluster repair

Jan 31, 2010 | 2003 Chevrolet Silverado 1500

4 Answers

Brakes are non-existent. Metal rubbing on metal


for the front it would be an hour of labor and you can get rotors for about 150 but dont cheap on on rotors or pads and get the good ones because theyll last longer. the front and back would be about 2 hours

Nov 19, 2009 | 1997 Chrysler Sebring

2 Answers

Similar issue


dear friend-the warrenty on a clutch is only 20 000 km,therefore you have to pay for the replacement,but 2500 dollars is a bit steep i suggest you get more quotes befor reparing.

Jun 30, 2009 | 2006 Hyundai Tiburon

2 Answers

VW PASSAT 2002 BRAKE QUOTE, PLEASE HELP!


your getting ripped
parts and labor should be no more than 200.00 call auto zone and price the parts yourself

Mar 30, 2009 | 2002 Volkswagen Passat

2 Answers

How do I replace the Alternator in my 99 A6 Quattro


its virtually impossible to do i had mine done at a local import dealer for 500.. try that instead of audi stealership.

Nov 13, 2008 | 1999 Audi A6

Not finding what you are looking for?
2004 Cadillac SRX Logo

Related Topics:

557 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...