Question about 1994 Pontiac Grand Prix

Open Question

Turn signals stay on instead of blinking

Already replaced bulbs, fuse, and turn signal relay

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1056 Answers

SOURCE: Signal lights don't work

Check the fuse, and the flaser relay (usually located on the fuse block)

Posted on Jul 27, 2008

  • 5 Answers

SOURCE: Turn signal flash circuit

Take the panel under the steering wheel off and its behind a little lip on the right side (left side of the stereo)

Its real easy to get too after you take that panel off.

Posted on Mar 22, 2009

  • 1 Answer

SOURCE: 99 Grand Am Turn Signal Relay Actuates By Itself

I had this problem quite some time ago and found a solution in a grand am forum. I rember I took off the top plastic panel on top of the steering column and there is a single screw (torx?) underneath. Remove the screw and the entire turn signal and wiper arms come up and off. There is a copper plate that will have grease in the slots, clean the grease off and it should be ok. It has been a while but I remember the clicking sounded like it was coming from the hazzard swith behind the radio but that was not the problem-it was the copper plate. It is an easy fix. Hope this helps.

Posted on Apr 19, 2009

  • 94 Answers

SOURCE: Turn signal is blinking fast. Brake light not

Turn signals sometimes blink fast when bulbs are burnt out-change bulb and you shuld be fine.

Posted on Feb 05, 2011

redds55
  • 2620 Answers

SOURCE: 1995 Pontiac Grand Am, turn signals do not work.

Bad connection or ground

Posted on May 08, 2011

Testimonial: "If the bulbs work when the hazard switch is activated, where would the bad connection be?"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alpha Romeo 156 My Left hand indicator light stays on continually, does not flash. and when I turn the hazard light switch on both indicators continually glow.


Generally speaking, symptoms of a bad or failing turn signal bulb are usually the culprit...in your case, either it's the front left or rear bulb. Varies for different vehicle makes...common signs include:
  1. turn signal light staying on solid
  2. or blinking very fast
  3. or either sides of the bulbs stop blinking altogether.
To test this, make sure you reconnect everything you disconnected.
Turn the left signal light on; go to the front of the vehicle, is the turn signal bulb illuminated? If it lights up, even though it is not blinking obviously the bulb is okay. If it doesn't, replace it- problem solved. You'll do the same procedure for the rear turn signal Is that lit up? If not replace the bulb and the problem is solved.
Another common failure is when the turn signal blinks really fast, same procedure as mentioned above.
If both bulbs for the left side and right side illuminate but don't blink, the problem is in the steering column turn signal switch.
If the left or right side blinkers don't work properly at all...then check the integrated hazard warning/turn signal flasher relay- that may be defective; again, that's usually the case if both sides of the signal light don't work.
If you are blowing any fuses related to the flasher system, you have an electrical overload in the turn signal circuitry.

Feb 12, 2017 | Cars & Trucks

1 Answer

Turn signal relay location


look in the fuse box location, follow the diagram for the signal relay or
you can turn on the signal to hear the clicking sounds to locate it

Sep 29, 2015 | 2004 Lincoln LS

1 Answer

What would cause flasher fuse slot to not have power on 1996 buick regal?


If It is not blinking then it's probably a blown bulb, That's how cars tell you a turn signal is bad. You will only have power to fuse slot when turn signal is on and the blinking part runs through a flasher relay so you could have a bad flasher relay if the bulbs are all good.

May 23, 2014 | 1996 Buick Regal Olympic Gold

1 Answer

Turn signal flasher relay location in


Turn signals use what is called a flasher to regulate the speed at which the lamps turn on and off. Usually mounted in the fuse box. I have attached the replacement model for a 1996 Roadie. Should take all of 15 seconds to replace.

Mar 16, 2014 | Buick Roadmaster Cars & Trucks

1 Answer

1998 Dodge Durango flasher relays location


Turn on the Durango and check each of the four turn signals to make sure that the bulbs are not burned out. If you find one that has gone out, replace the bulb and retest the turn signals. When a bulb goes bad on this circuit, the resulting operation can mimic a bad flasher or one that is failing.

Locate the combination turn signal flasher and relay. It is on the left end of the driver's dash. Open the access door and view the collection of relays and fuses. At the left side of the mounting block is a larger flasher and relay. This is the combination turn signal flasher and relay.

Test the relay by placing you finger on the relay housing and activating the turn signal. If you have found the right one, you should feel a clicking as the turn signal blinks. Remove the relay, replace with the new relay and close the access door

.

Start the Durango and activate the turn signals to check that they each work. The light should turn on and should blink. Also, check the hazard lights to make sure they work.

Feb 11, 2012 | Dodge Ram 1500 Cars & Trucks

1 Answer

I replaced the turn signal bulbs for the driver side of my 1986 Chevy S-10 truck and both lights work but stay on instead of blinking. What else is the problem? Both bulbs are brand new and the passenger...


the blinker is bad, yes no kidding it is a relay type part. usually it is silver cylinder shape. When these burn out it will not blink. Easy to replace, just like a fuse, unplug the old one plug the new one in. Sometimes the part is called a flasher. Hope this helps

Jun 08, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

Turn signals won't blink


relay is bad turn signal relay

Jul 31, 2009 | 1998 Dodge Durango

1 Answer

Dont have signal


Click the turn signal switch to either the right or left and get out and check if the BULB comes on but doesn't blink. Try both directions. Does the arrow for that direction also come on, on the dashboard instruments and stays on but not blink? That is a built in indicator that a filament has burned out in one of the bulbs. Try replacing the bulbs. Could also be the fuse for that circuit. Check fuse panel for that circuit. Could also be the turn signal relay. Replace with newer style relay.

Jul 15, 2009 | 1996 Geo Prizm

1 Answer

Turning signals


hi if idicators when selected right or left turn ? do not blink but stay on? then this is the indicator relay(flasher unit) gone faulty located in fuse relay box? if you check h/book? it will give indication or look on underside of relay cover ?

Oct 07, 2008 | Hyundai Motor 1995 Accent

Not finding what you are looking for?
1994 Pontiac Grand Prix Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...