Question about 2003 Nissan Pathfinder

Open Question

Dtc p0011 nissan pathfinder - 2003 Nissan Pathfinder

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76109 Answers

SOURCE: p1230 dtc on 1996 nissan pathfinder

P1230 refers to ign coil that has an internal open on the primary side of coil

Posted on Aug 09, 2012

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does the code no DTC detected mean on a 2001 Nissan pathfinder


DTC P1441 means there were no scan results. There may be some troubles that can't be detected but the fact that your Nissan is running fine seems at odds with that long list of issues cobbled together by the repair shop.

Feb 18, 2015 | 2001 Nissan Pathfinder

1 Answer

What does no dtc code on a 2001 Nissan pathfinder mean


DTC = Diagnostic Trouble Code.
No DTC means no trouble.

Feb 18, 2015 | 2001 Nissan Pathfinder

1 Answer

Code p0011


http://www.datsc.com/tabid/122/OBD-Error-Code/P0011/Diagnostics/Mercedes-Benz/Default.aspx
"..........OBD Code P0011refers to
A code P0011 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0011 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft.

SymptomsPossible sumptoms of OBD code P0011
Most likely a P0011 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.

CausesPossible causes of OBD code P0011
A P0011 DTC trouble code may be caused by one or more of the following: Incorrect camshaft timing Wiring problems (harness/wiring) in intake timing control valve control solenoid system Continuous oil flow to VCT piston chamber Failed timing valve control solenoid (stuck open)

Possible SolutionsThis DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.

Related CodesP0010 P0012 P0020 P0021 P0022..........."

Oct 04, 2013 | Mercedes-Benz Cars & Trucks

1 Answer

2002 altima codes 1212 and 0011 please help


DTC P1212 - Mass Air Flow Circuit Intermittent Low
DTC P0011 - "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

A P0011 DTC trouble code may be caused by one or more of the following:

  • Incorrect camshaft timing
  • Wiring problems (harness/wiring) in intake timing control valve control solenoid system
  • Continuous oil flow to VCT piston chamber
  • Failed timing valve control solenoid (stuck open)

Possible Solutions

This DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 21, 2012 | 2002 Nissan Altima

1 Answer

P1230 dtc on 1996 nissan pathfinder


P1230 refers to ign coil that has an internal open on the primary side of coil

Aug 09, 2012 | 1996 Nissan Pathfinder

1 Answer

03 Maxima SE... Check engine light is on and getting codes P0011 AND P0021 which is the intake camshaft position timing over. I also have P0462 because my fuel level sensor always reads as full and while...


Hi there Camilo:
DTC P0011 - "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)
A code P0011 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0011 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft.
Potential Symptoms

Most likely a DTC P0011 will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.
Causes

A DTC P0011 trouble code may be caused by one or more of the following:
- Incorrect camshaft timing
- Wiring problems (harness/wiring) in intake timing control valve control solenoid system
- Continuous oil flow to VCT piston chamber
- Failed timing valve control solenoid (stuck open)

Possible Solutions:
This DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.

Other related DTCs: P0010 - P0011 - P0012 - P0020 - P0021 - P0022
----------------------------------------------------------------------------------------------------------------

DTC P0462 - Fuel Level Sensor Circuit Low
This could happen happen you ran your fuel tank too low I would first fill up the tank and go to your local parts store and have them reset the code to see if it stays off .If the light comes back on the most likely reason is because the fuel level sensor needs to be replaced but other possible causes are wiring problems, fuel pump module, or cluster. You will need to barrow a special tool which is the lock wring wrench from your local parts store to remoe the fuel pump. Here are instructions from Nissan TSB (Technical Service Bulletin) to solve it; let me know if you have questions.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jan 31, 2012 | 2003 Nissan Maxima

1 Answer

Has dtc #c0561 and engine code #p0011-breifly explain description


code P0011 intake camshaft position performance ( could be a camshaft sensor, or could be that the intake camshaft variable timing unit is stuck try changing the oil and filter and add some seafome to the oil clear the code and drive it and see if the code comes back)

code C0561 system disabled information stored ( the electronic brake control module disables the traction control system when their is a DTC stored that might effect the traction control system, could be caused by the P0011 )

Apr 19, 2011 | 2006 Chevrolet HHR

1 Answer

Identified as P0011


P0011 - "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

What does that mean?
A code P0011 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0011 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft.

Potential Symptoms:
Most likely a P0011 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.

Causes:
A P0011 DTC trouble code may be caused by one or more of the following:
* Incorrect camshaft timing
* Wiring problems (harness/wiring) in intake timing control valve control solenoid system
* Continuous oil flow to VCT piston chamber
* Failed timing valve control solenoid (stuck open)

Possible Solutions:
This DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.

Other related DTCs: P0010 - P0011 - P0012 - P0020 - P0021 - P0022

Hope helps (remember rated this).

Jun 25, 2010 | 2003 Nissan Altima

2 Answers

My check engine light is on had Auto Zone run a check and it says P0011 code? Is this a serious issue? And what could be causing this?


The generic code for P0011 is Camshaft Position_ Timing over-advanced or System performance Bank 1

Apr 08, 2010 | 2005 Nissan Sentra

2 Answers

P0011 altima 3.5l 2005


P0011 (Bank 1)
Intake valve timing control performance, There is a gap between angle of target and
phase-control angle degree.
Causes:
- Harness or connectors (Intake valve timing control solenoid valve circuit is open or shorted.)
- Intake valve timing control solenoid valve
- Crankshaft position sensor (POS)
- Camshaft position sensor (PHASE)
- Accumulation of debris to the signal pick-up portion of the camshaft

Jun 17, 2009 | 2002 Nissan Altima

Not finding what you are looking for?
2003 Nissan Pathfinder Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...